Whirlpool Washer Parts

Left-hand lid hinge for washer top panels. Replace if rusted, cracked, or broken to restore smooth lid opening and proper alignment with lock mechanism.

Fixes F02 drain error codes and slow draining. This small ball creates a seal in the tub-to-pump hose to control water flow. Simple DIY replacement.

Replacement retaining nut for washers and dryers. Secures components like pulleys, shafts, and assemblies. Order a new nut if yours is stripped or missing.

Contains two, six foot long braided hoses with 90 degree ends.

This gray control knob replaces a worn or broken knob on the console so you can accurately select settings. It fits onto the timer/selector shaft and restores a secure grip with smooth, positive engagement. What it does:

• Attaches to the control/timer shaft on the front panel
• Lets you turn and select cycles or options
• Restores a snug fit when the original knob is cracked or stripped
• Common symptoms: knob spins freely, falls off, won't turn settings, or is missing

• 1 gray control knob

• Disconnect power before servicing
• Pull the old knob straight off the shaft; retain any insert/clip used by your model
• Align the new knob with the shaft and press firmly until fully seated
• Test all settings for proper engagement

Touch-up paint for appliances. Covers chips, scratches, and worn areas on range tops, refrigerators, and other appliances. Includes brush applicator.

Two 5-foot nylon braided hoses connect household water supply to washer inlet valves. Replace cracked, leaking, or aging hoses to prevent water damage.

This dishwasher dispenser stores detergent and rinse aid and releases them at the correct points in the cycle to support consistent cleaning results. Replace a broken, stuck, or leaking dispenser to restore reliable detergent delivery.

• Holds detergent and rinse aid and dispenses them automatically during the wash and rinse portions of the cycle
• Door/actuator mechanism controls the timed release of detergent
• Seals help prevent leaks around the dispenser opening
• Typical failure symptoms: detergent cup won't latch or open, detergent left in the cup, rinse aid not dispensing, or leaks from the dispenser area

• Disconnect power and turn off water supply before servicing
• Remove the inner door panel to access the dispenser; disconnect the wire connector
• Release mounting screws/clips, clean the door cutout, and seat the new dispenser evenly
• Tighten screws in a cross pattern to compress the gasket uniformly; run a test cycle to check for leaks and proper operation

Adjustable leveling foot threads into washer or dryer base to stabilize appliance on uneven floors. Replace if cracked, worn, or missing to reduce rocking.

Adjustable leveling foot that supports and stabilizes your refrigerator. Replace if worn, broken, or missing to eliminate wobbling and vibration.

The Wire Harness is an OEM part for Whirlpool washing machines. The wire harness is responsible for transmitting electrical signals that power components and allow them to communicate during each cycle.

Causes of a bad wire harness can be normal wear and tear over time, pinched or cut wires, or wire insulation breakdown due to heat or moisture exposure.

Symptoms of a bad wire harness include:

• Lights or display not working properly
• Washer not starting cycles
• Sensors or switches malfunctioning
• Intermittent operation

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Creates a watertight seal between the washer door and tub. Replace if you notice leaks, tears, or mold buildup. Confirm fit with your model number.

This three-circuit connector housing organizes and protects terminals in an appliance wiring harness. It provides a secure, insulated plug connection to help prevent loose contacts, heat damage, and intermittent operation when the original housing is cracked or melted. What it does:

• Holds three wiring terminals in the correct orientation for a mating connector
• Insulates and locks terminals to reduce arcing and overheating at the plug
• Replaces cracked, brittle, or heat-damaged connector housings
• Symptoms can include intermittent power, burnt odor near the connector, discoloration/melting, or a plug that won't stay latched

• 1 three-circuit connector housing

• Disconnect power before servicing the appliance
• Note wire/terminal positions and transfer them one at a time into the new housing
• Inspect terminals; replace any that are discolored, loose, or damaged. Use the correct crimp tool/terminals specified for your model
• Fully seat each terminal until it locks and the connector latch engages securely

PC-144 agitator that moves and tumbles clothes during wash cycles to help loosen soil and distribute water and detergent. Replacing a worn or damaged agitator restores proper wash action and improves cleaning performance. What it does:

• Uses fins/paddles to lift and move garments so water and detergent reach fabric fibers for better cleaning.
• Promotes even water circulation and load movement to reduce tangling and bunching.
• Common service reasons: cracked or broken fins, missing or worn agitator, noisy operation, excessive vibration, or clothes not coming out clean.
• Designed for top-load agitator-style wash systems that use the PC-144 agitator design.

• Disconnect power (unplug) and turn off water before starting any repairs.
• Typical replacement requires removing the existing agitator cap and any retaining hardware, then sliding the agitator off the drive post and installing the new unit; procedures vary by model—refer to your model's service manual or diagram.
• If a retaining bolt or special fastener is used on your model, have the correct socket or tool ready; follow manufacturer guidance for proper securing.

Adjustable front leveling leg for washers. Replaces damaged, broken, or missing feet that cause rocking and vibration. Installs at front base to level unit.

Timer knob assembly mounts to the control shaft for manual cycle selection. Replaces a cracked, worn, stripped, or missing knob on your laundry center.