Whirlpool Wire, Harness, Power Cord

This wire harness routes power and signals between an appliance's controls and components to restore reliable electrical connections. Replacing a damaged harness helps eliminate intermittent or failed electrical paths and unsafe wiring. What it does:

• Carries power and control signals between the control board and components.
• Restores proper electrical connections when wires or terminals are burned, frayed, or broken.
• Commonly used to address intermittent operation, failure to start, or components not responding.
• Helps prevent shorts or arcing caused by damaged insulation or loose terminals.

• Disconnect power before starting any repair.
• Compare connectors and wire routing to the original; replace only if identical.
• Disconnect and reconnect connectors by hand; avoid pulling on wires. Use proper tools when needed.
• Follow OEM wiring diagrams and secure routing/clamps to prevent chafing or heat exposure.

This wire harness routes power and signals between the appliance control and key components so the unit can operate correctly. Replacing a damaged harness restores reliable electrical connections and helps eliminate intermittent faults. What it does:

• Carries power and control signals between the main control, motors, switches, sensors and other components
• Restores proper electrical connectivity when wires are frayed, burned, or connectors are loose
• Can stop intermittent operation, components that don't receive power, or erratic control behavior
• Helps prevent electrical arcing or shorts caused by damaged wiring

• One wire harness as shown

• Always disconnect power (unplug or switch off circuit breaker) before beginning service
• Inspect connectors and wire terminals for corrosion or damage; match connector orientation during reassembly
• Replace only with the exact harness for your appliance model to ensure correct fit and wiring

The Power Cord is an OEM part for Whirlpool dishwashers. This kit provides you with all the necessary parts to safely and effectively connect your dishwasher to the power source. The kit includes one power cord with a right angle head, one grommet, and one metal strain relief. The power cord with a right angle head allows for easy installation and helps to prevent excessive bending or damage to the cord.  

A bad power cord can occur due to wear and tear, exposure to heat or moisture, or accidental damage. If you notice symptoms such as intermittent power supply, sparks or electrical arcing, or a loose connection, it may be time to replace the power cord kit.

Symptoms of a bad power cord include:

• Intermittent power supply
• Sparks or electrical arcing
• Loose connection

Restore your Whirlpool dishwasher by replacing the faulty or damaged power cord kit with this genuine OEM part.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

The Power Cord is an OEM part for Whirlpool dishwashers. This kit provides you with all the necessary parts to safely and effectively connect your dishwasher to the power source. The kit includes one power cord with a right angle head, one grommet, and one metal strain relief. The power cord with a right angle head allows for easy installation and helps to prevent excessive bending or damage to the cord.  

A bad power cord can occur due to wear and tear, exposure to heat or moisture, or accidental damage. If you notice symptoms such as intermittent power supply, sparks or electrical arcing, or a loose connection, it may be time to replace the power cord kit.

Symptoms of a bad power cord include:

• Intermittent power supply
• Sparks or electrical arcing
• Loose connection

Restore your Whirlpool dishwasher by replacing the faulty or damaged power cord kit with this genuine OEM part.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This wire harness routes power and signals between key components for consistent performance. Replacing a damaged harness restores reliable connections and correct operation of affected controls, motors, or sensors.

• Distributes electrical power and control signals between boards, switches, sensors, and motors
• Replaces cut, brittle, burned, or corroded wires and terminals that cause connection faults
• Common symptoms include intermittent operation, a component that won't run, or error codes related to poor connections
• Restores proper wire routing when installed in the factory path and secured with clips/ties

• Disconnect power before servicing; turn off water or gas supply if applicable
• Photograph and label existing connections; move plugs one at a time to the new harness
• Route along the original path; secure in clips/ties and keep clear of sharp, hot, or moving parts
• Seat each connector fully by the plug body (do not pull on wires); inspect mating terminals for heat damage

This replacement power cord restores the appliance's main electrical connection so your unit can receive power safely and reliably. Use it to replace a damaged or worn cord that causes power loss or intermittent operation. What it does

• Provides the primary electrical connection between the appliance and wall outlet.
• Replaces frayed, cut, or otherwise damaged cords that can cause intermittent power or no power.
• Helps eliminate arcing or visible cord damage that may create safety risks.
• Returns dependable power delivery so the appliance can function as intended.

• Always unplug the appliance or disconnect power at the breaker before starting work.
• Route the cord and attach any strain relief or mounting hardware exactly as the original; secure all wiring connections.
• Inspect connectors and wiring for damage before reconnecting power.

This wire harness connects the appliance's control and power circuits to key components, restoring reliable electrical communication and control. It replaces a damaged or frayed harness to help resolve intermittent power, no-start, or unresponsive control issues. What it does:

• Carries power and signals between the control board and components like motors, switches, and heaters
• Restores continuity when original wires are burned, cut, or have broken connectors
• Helps stop intermittent operation, control failures, or components that no longer receive power
• Matches OEM routing and connectors for a direct replacement when specified

• One complete wire harness as shown

• Disconnect all power before attempting replacement to avoid shock or injury
• Tighten any mounting clips and secure wiring away from heat or moving parts

This wire harness assembly connects the appliance's control components to power and sensors, restoring reliable electrical signaling and operation. Use it when damaged wiring or connector failures cause power or control faults. What it does:

• Routes electrical power and signals between the control board, user interface, and major components
• Replaces frayed, burned, or broken wiring that can cause intermittent or lost control functions
• Restores proper connector fit for secure electrical connections
• Helps resolve symptoms such as unresponsive controls, intermittent operation, or visible wire damage

• Disconnect power before servicing to avoid shock or injury
• Verify connectors match and seat fully; replace any damaged clips or fasteners
• Handle connectors by the plug bodies—avoid pulling on wires

This wire harness assembly routes power and control signals between the appliance's main control and its components to restore reliable electrical connections. It replaces a damaged or intermittent wiring assembly to help components receive proper power and signals. What it does

• Connects the main control to heating elements, sensors, switches, or other components depending on appliance model
• Restores lost or intermittent power/signal paths caused by frayed, burned, or broken wires
• Helps resolve symptoms like components not powering, intermittent operation, or electrical arcing at connection points
• Maintains correct wire routing and connector fit for safe operation when installed properly

• Disconnect all power (unplug or switch off breaker) before beginning work
• Photograph existing routing and connector locations to ensure correct reinstallation
• Route harness without pinching; secure with original clips or ties and avoid heat sources

This wire harness assembly routes power and control signals between components to restore proper electrical connections. It replaces a damaged or worn harness to help resolve power loss and intermittent operation. What it does:

• Delivers power and signal connections between control, motors, switches, and sensors.
• Restores reliable electrical continuity when old wires are frayed, broken, or corroded.
• Helps eliminate symptoms like no power to components, intermittent operation, or electrical shorts.
• Keeps wiring organized and properly routed to prevent chafing and accidental disconnection.

• One wire harness assembly as shown.

• Disconnect power to the appliance before starting any repairs to avoid shock.
• Ensure all connectors are fully seated and that wires are secured away from sharp edges and moving parts.