Dryer Touch Pad

This back panel assembly replaces a damaged or missing rear cabinet panel to protect internal components and keep the unit's cabinet aligned and secure. Restores a clean fit and helps reduce rattles from a loose or bent back. What it does:

• Encloses and protects internal wiring and components at the rear of the unit
• Provides mounting points for rear hardware and brackets
• Helps maintain cabinet alignment and structural rigidity
• Can reduce noise from vibration when the rear panel is properly secured

• One back panel assembly

• Disconnect power before servicing; if applicable, shut off gas supply
• Pull the unit forward to access the rear; wear cut-resistant gloves—edges can be sharp
• Retain and transfer any clips, ground straps, or grommets from the old panel
• Route wires carefully and tighten fasteners evenly so the panel sits flush

Dryer back panel assembly houses control switches and touch pads. Replace if cracked, broken, or switch mounts are damaged causing buttons to fall through.

Replaces cracked or broken dryer backsplash assembly. Provides mounting surface for timer and switches. White panel with cycle graphics restores appearance.

Replaces cracked or broken dryer control console back cover. Forms rear housing that supports timer, controls, and shields wiring. Easy DIY fix.

This control panel assembly replaces the white front console on your dryer. It restores a solid mounting surface for the timer, switches, or display so you can select cycles and settings with proper alignment and smooth operation. What it does

• Provides the front console housing for the dryer's user controls
• Keeps buttons/knobs and indicators aligned and protected
• Restores appearance after cracks, discoloration, or broken tabs
• Helpful when controls feel loose, are hard to press, or the console is rattling

• 1 white control panel assembly

• Disconnect power; if gas, shut off the gas supply before servicing
• Remove control knobs and any end caps; take out mounting screws/clips and lift off the old panel
• Transfer any brackets, light pipes, clips, and harness retainers from the old panel to the new as needed
• Reinstall and tighten fasteners; refit knobs and verify smooth control operation before restoring power

This replacement control panel, also called the backsplash assembly, is the structural console on the rear of the dryer top where the timer and switches mount. It restores secure control mounting and a clean, finished appearance when the original is cracked or damaged.

• Houses and supports the dryer's timer and control switches
• Covers and helps protect console-area wiring from contact
• Aligns control shafts through the panel openings for smooth knob operation
• Common signs of failure: cracked panel, broken mounting tabs, loose or rattling controls

• Disconnect power; for gas models, also shut off the gas supply
• Remove control knobs and mounting screws, then tilt or lift the console to access the panel
• Transfer timer/switches and any brackets from the old panel to the new one, keeping hardware organized
• Do not overtighten screws; verify all controls turn and click freely before restoring power

This is a control panel.

Control panel assembly with touchpad for your dryer. Mounts on top of the unit. Replace if buttons are unresponsive, cracked, or display is damaged.

This white backsplash assembly restores the finished rear appearance of a range and helps protect the wall from spills, splatters, and heat. It provides a clean, factory-fit rear cover for affected models. What it does:

• Covers and protects the rear wall area behind the range from grease, food splashes, and light heat exposure
• Restores the appliance's factory appearance when the original backsplash is damaged or missing
• Secures to the range frame to provide a finished mounting surface for rear components on applicable models
• Prevents debris from entering gaps between the appliance and wall

• Disconnect power (and gas, if applicable) before beginning service
• Remove screws or fasteners holding the old backsplash; save hardware for reassembly if reusable
• Handle edges carefully; use proper hand tools and follow the appliance wiring/part diagram

Replace your dryer's control panel touch pad if the overlay is cracked, worn, or buttons are unresponsive. Installs on the front panel assembly.

White control panel touch pad assembly for your dryer. Replaces worn, cracked, or unresponsive touch pads. Installs on the control console exterior.

Restores the finished control panel area on your dryer. Replaces a cracked, dented, faded, or missing backsplash assembly with printed graphic.

Replacement touch pad control panel for your dryer. Installs on the front console. Needed when buttons are unresponsive, cracked, or worn from use.

Replacement touch pad for dryer control panels. Installs on the console to restore button functionality. Needed when buttons are unresponsive or worn.