Need Help?
Call or text
Oven won't turn off or stays on low heat? This temperature-sensing thermostat regulates oven heat and prevents overheating. Moderate DIY repair.
I replaced the thermostat and its control switch as it was not able to turn off. Read more
Microwave has no power or won't start? A faulty cavity thermostat often causes complete shutdowns. This part restores temperature control in 5-10 minutes.
I attempted to diagnose the four thermostats/thermal switches in the microwave....two right behind the control panel, one on top of the cooking cabin, and one under a metal shroud above the magnetron. While checking continuity with a voltmeter, i questioned one of them behind the control panel and the one above the magnetron. I then noticed a burn mark on the plastic connector sleeve for the one above the magnetron. I took a scrap piece of 14 gage copper wire and beat the ends flat with a... Read more
Fix a burner that won't light or clicks repeatedly with a new spark electrode. Creates the electrical arc that ignites gas at your cooktop burner.
I replaced all 4 ignitors and new clips. Read more
Color: black. Measures about 2 inches in diameter.
Replaced burner tubes and installed a new nob on the sparker control. Read more
Replacement oven bottom panel that forms the floor of your gas range oven cavity. Needed when original is warped, rusted, cracked, or peeling.
I replaced the Oven Igniter. After ensuring that it was the igniter, by turning on the stove and taking out the oven bottom. Watch if it turns red. If not, then either the wiring is faulty, or the igniter went bad. The bulb was due to a loose and broken light bulb, can't use any normal bulb, these ones are specially made to withstand the heat. And the oven bottom was warped due repeatedly heating up and cooling down over the years. It took a fair bit of time to get the new one in, since it was... Read more
Fix burners that won't light or spark intermittently with a new surface burner igniter. Most DIYers complete this repair in 20 minutes with basic tools.
I disassembled the top of the range and looked at the problem burner. It looked like there was a spark at all three other burners but not the problem burner. There was a visible spark at the connector between the wiring harness and the ceramic igniter but that spark wasn't making it up to the top of the igniter where it can light the burner. I ordered a new igniter for $19 and it was on my doorstep the next day. I replaced the part and now my wife thinks I am a genius. Don't tell her that... Read more
Oven not heating or baking unevenly? This lower bake element restores consistent bottom heat. Simple DIY repair—clips in and tightens in 5-10 minutes.
New part clipped right in. Tightened 2 screws and was done in 5 minutes. Read more
Replace your worn oven door gasket to restore a heat-resistant seal, stabilize temperature, and improve baking performance. Confirm fit with your model number.
Replaced tempered glass and oven seal/gasket. Read more
This Door Hinge supports and pivots the appliance door for smooth operation and a square, reliable close. Replacing a worn hinge restores alignment so the door seals properly and opens and closes without binding or noise. What it does
Door hinge replacement and of course a new fuse. All went very well. Good service and tech support from AppliancePartsPros.com Read more
Exhaust fan won't turn off or stuck on? This rocker switch restores reliable blower control. Simple 5-minute fix—just disconnect wires and snap in new.
First check to see how many leads your switch has before ordering - I ordered before I took things apart, and got an incorrect 2 lead version when I needed a 3. On starting the repair, at first thought I might have to take apart console - but happily, no. After turning off power, just carefully pried the old switch out (putty knife to depress plastic clips above & below), pulled out gently (not much slack on wires) and removed the old wires by gently easing them off the broken switch with a... Read more
Adjustable front leveling leg threads into the base corner of your range to raise or lower the unit. Replace if broken, cracked, or missing to level your range.
Could not level stove. Front leveling legs had pieces broken out where leg contacted floor. Back leveling legs were worn and did not stay at corrected height when stove returned to full weight on floor. Replaced both front and back leveling legs, and stove was able to be leveled. Also bought Touchup Paint for numerous nicks and scratches - color matched perfectly. Read more
Color: chrome. Measures about 1 inch in diameter.
Turned off 40 Amp breaker. Removed shelves from oven. Removed two screws in back panel holding element in place. Slowly pulled element free making sure wires stayed attached and not lost in oven insulation. Removed two wires from old element. Attached wires to new element. Pushed wires back into oven rear wall. Reinstalled the previously removed two screws. Turned on breaker. Total time less than 10 minutes. Read more
Replaces a damaged, missing, or incorrect LP bake burner orifice in gas ranges. Essential for propane conversion to meter gas properly to the oven.
Pulled the old orifices and submitted a question about the proper replacements for my model. received a prompt reply with links to the correct parts. Added them to my cart and purchased, they arrived soon after and installed easily. Hooked up the range and it works perfectly. Read more
Surface burner cap sits on top of the gas burner head to shape the flame. Replace if yours is missing, chipped, cracked, or warped for proper appearance.
Husband did that. Found a burner cap kit. Said it was simple. Read more
Fix clicking noise, poor cooling, or overheating compressor by replacing a cracked or warped condenser fan blade. Restores airflow across the coil.
At first, I thought that it was the defrost timer, but when I took apart the freezer, I found that the evaporator fan motor wasn't running, so I replaced it. Read more
Captures grease and debris from cooking vapors. Replace when clogged or discolored for optimal ventilation. Confirm fit using your model number.
Took off the vents to clean it good. Saw the charcoal filter. Needed to be replaced (had been 13 years) popped the new one in. While I was at it got a new grease filter which slides in easily. Read more