Amana Range Parts

• Shakes and moves

REPLACING THE SUSPENSION PADS AND REPLACE THE BALNCE RING EVEN IF MY DIDN'T LEAK ANY FLUID OUT OF IT... IT SOLVE THE PROBLEM, IT WORKS BETTER NOW THAN IT EVER DID, THE ONLY THING I COULD COME WITH IS THE MANUFACTURE PUT THE WRONG BALANCE RING IN IT TO START WITH... MY IS A 400 KENMORE TOP LOADER, IT IS THE EASIES WASHER I HAVE EVER TAKEN A PART.. I WISH CARS WERE THAT EASY... IT TOOK ME OVER A MONTH FIGHTEN THIS PROBLEM UNTIL I FOUND IT ON YOUTUBE... WHAT BLESSING IT WAS... Read more

• Element will not heat
• Won't start

Turned off power supply. Removed two screws (near the oven door) holding the ceramic top. Slid the top forward, disengaged the two power supply cables, and removed one ground wire. Removed range top, and put on a flat surface. Unclamped two power supply wires, one ground wire and one thermocouple wire from the element. Unscrewed the bracket from the element, and remove the element from the range top. Remove the two clamps from the old element, and put them on the new element at the same... Read more

• Door won't close

I have a Jennair jjw9630cas double wall oven, and after a few years I noticed that the light would not go out, first in the bottom oven, and then in the top oven. After doing some research I discovered this was not uncommon, and the fix usually involved replacing the hinges and/or the hinge receptacles. It didn't look like a difficult fix so I ordered four new hinges and four new receptacles, which arrived quickly. I found a video on YouTube that showed how to replace the hinges and it... Read more

DIY. The delivery to Milwaukee took two days. The project was very easy and took about 1hr. The only tools required were a screw driver (electric) and a pliers. Just make sure your irganized with the screws so you don't lose any or mix up which ones go back in which holes. There's about 20 total screws. This $50 part saved me from having to buy my wife a $1000+ oven. Read more

I went online to Appliance Parts Pros and with only my model # and serial # of my range, it was a simple fix! They not only had the part I needed, but they provided the expanded drawing so I could see what was needed and when I had a question and emailed them, I received a response within a couple of hours. They shipped right away and the glass was at my front door in 2 days! This company is fantastic!!!! Read more

• Element will not heat

Personally I have experience working with electricity and knowing if I bought the part required this would be an easy fix. I got my model number and contacted Appliance Parts Pros and placed my order for the new elements, terminal blocks, and for appearance purposes 4 new Drip Pans. Excellent service and quick shipping. I ordered my parts on Sunday and received them on Tuesday. This was a simple repair that only required a screwdriver to remove the old terminal block from the range hood, wire... Read more

Checked the three door switches; used ohm meter to see if there was resistance or if a switch was bad. 2 out of 3 switches showed resistance with the ohm meter. The last one tested (of course the last one) NO (normally open) did not show resistance; I.e. the ohm meter reading did not change when the switch was depressed. Appliance parts pros was the only company that had the same model number I was looking for (SZW-V16-FD-63). I ordered the relay switch, 2 days later it arrived (regular... Read more

• Little to no heat when broiling

I had the choice of spending $2K on another double oven stove or $60 on two elements. (I felt more secure about replacing both bake and broil elements just in case the fire had damaged the bake element) It was an easy decision and quick replacement! Power was already off to the stove so I cleaned up the fire retardent mess. I even found easy instructions dismantling the oven door in order to clean the powder residue from between the glass. I then removed the rack and remaining old elements. I... Read more

Dropped light panel by removing two screws with socket set. Unplugged two terminals and unclipped the light socket from the base. Then just clipped the new socket onto the base, plugged the connectors onto the terminals and remounted the base. Total job was less than 15 minutes. Read more

Took the back off the stove, took the switch out put the new switch in but it all back up Read more

• Element will not heat
• Won't start

Full disassembly of removable tray into top plate (stainless) and lower pan taking care not to loose fasteners. Removal of terminal blocks using lubrication on rusted screws and, if necessary, drill out technique. Unclip wires from edges of the tray on both sides without losing the clips for future re-use. Top plate is now completely free of connections and may be cleaned/scrubbed separately in advance of re-assembly. Unfasten spade insulation block (located in the front of the tray) after... Read more

Checked the three door switches; used ohm meter to see if there was resistance or if a switch was bad. 2 out of 3 switches showed resistance with the ohm meter. The last one tested (of course the last one) NO (normally open) did not show resistance; I.e. the ohm meter reading did not change when the switch was depressed. Appliance parts pros was the only company that had the same model number I was looking for (SZW-V16-FD-63). I ordered the relay switch, 2 days later it arrived (regular... Read more

• Element will not heat
• Won't start
• Gas igniter glows, but will not light

Replaced ignitor. Read more

I did a search online for inner door glass replacement pieces and came across a youtube video made by appliance parts pros. After watching the video, I was certain that this was a repair I could do myself. I ordered the glass and it arrived the next afternoon. That evening, I brought the video up on my computer, gathered a screwdriver, some gloves and a towel to lay the door on when I put it on the table. I watched the video as I did the repair, starting, stopping and backing up as needed. ... Read more

We bought replacements which fit very well and the burner elements are level again! Read more

1st. replaced thermostat probe inside wall oven - no change. Then removed range heating element and measured it with ohm meter for continuity and found it to be OPEN. Ordered replacement range heating element; measured it before install and found it to be a few ohms - installed in less than 5 minutes and tested. ALL WORKS GREAT. Both items purchased with shipping were just over $100. (I chose to keep the thermostat probe instead of returning it being the oven is just over 10 years old). Read more