Amana Range Parts

1st. replaced thermostat probe inside wall oven - no change. Then removed range heating element and measured it with ohm meter for continuity and found it to be OPEN. Ordered replacement range heating element; measured it before install and found it to be a few ohms - installed in less than 5 minutes and tested. ALL WORKS GREAT. Both items purchased with shipping were just over $100. (I chose to keep the thermostat probe instead of returning it being the oven is just over 10 years old). Read more

Removed existing gasket and replaced with new gasket in less than 5 minutes. Very Easy. Make sure to remove the lower burner cover (inside the oven) which allows you to pull the end gasket material through the two circular openings in the frame. Read more

We bought replacements which fit very well and the burner elements are level again! Read more

• Noisy

After having replaced the drum support rollers twice in a roughly 3yr period, I realized something wasn't quite right, and indeed it wasn't. I had been ordering the wrong parts - I did use the online parts locator after checking, & double checking my model number. Apparently my older Whirlpool dryer has a somewhat ambiguous model number because the rollers that were shipped each time looked nothing like the originals. I realize that is not particularily uncommon - manufacturers often modify... Read more

Bought a replacement gasket. Read more

Replace dual infinity switch. The only difficulty is the terminal labels on the new switch did not match at all with the terminal labels on the original switch. The enclosed instructions were NOT helpful. But I contacted your representative, Johnny, and he was most helpful and patient. From my model number he located very specific and detailed instructions for how to wire the new switch. The rest of the job was easy. Your representative was outstanding. Thanks. Read more

Had to replace the switch for the left rear burner on a Whirlpool cooktop Model W5CE3625AB00. I turned off the circuit breaker for the cooktop and lifted it out of the countertop. It was simply held down by its own weight. There were approximately a dozen screws holding the smooth surface down onto the rest of the unit. I removed those screws, which allowed the cooking surface to lift back on a hinge in the back of the unit. Two of those screws were stripped, but I was able to remove them... Read more

These drip pans fit! I had bought some from a local big box store and they didn't fit. I only wish they still made them without the holes in the bottom of the drip pan. How's that supposed to hold a boil-over? But that's the manufacturer. AppliancePartsPros have always sent me orders right on time. Read more

I replaced the bake element in the bottom of the unit. Read more

Well, I gotta say I was happy to find you still had parts for almost 20 year old microwaves. The microwave itself worked fine, so I hated to have to buy a new one, but I just couldn't take being hit in the head anymore; and my fix of using string and wire to tie it to the surrounding cabinets was unsightly to say the least. I'm glad I did some research and found this part - all I had to do was pop it in place and now the vent grill is secure. Problem solved with minimal cost. Read more

• Element will not heat

Replace burner and receptacle. The product arrived promptly after order and the receptacle came in a factory Whirlpool bag, indicating it was a genuine Whirlpool part. The burner did not have such identification, but works very good. I've placed 3 orders with these folks for various broken appliances, and each one has worked as advertised and performs like new. Read more

I ordered a new one Read more

• Gas smell
• Won't start

I replaced the burner head. I turned off power to the stove, although I did not turn off the gas. I gave the old burner head a slight twist counter-clockwise until it lifted off the stove. I used the pliers to pull the wires from the old burner, then placed them onto the contacts on the new burner. Set it in place, and gave it a clockwise twist until it was snug. This stove originally came with gaskets beneath the burners, but the info for the replacement part stated that a gasket was not... Read more

• Won't start

I purchased a new igniter for the bake assembly and found that it, unfortunately, did not resolve my problem. I measured the resistance of the different points on the gas valve and it was reading within spec so I then purchased this spark module and it did the trick. My gas range is a Kitchenaid kgsk901sss02. I had a LOT of trouble finding where the spark module is located, and eventually found a schematic that shows it's location behind the front control panel of the oven. Upon taking the... Read more

Replaced bake element to no avail, seeking help with live chat. FYI, order process and delivery time was top notch. Read more