Amana Washer Parts

The Capacitor is an OEM part for Whirlpool washing machines. This part stores and releases electrical energy to help start the washer's motor and maintain its operation during wash cycles. 

Causes of a bad capacitor can include electrical surges, overheating, or degradation over time.  

Symptoms of a bad Capacitor include:

• The washing machine not starting
• The motor humming but not running
• The washer stopping mid-cycle
• Unusual noises during operation

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Dryer Timer Knob is an OEM replacement part for Whirlpool dryers. It allows users to set the drying time and cycle, providing control over the dryer's operation. This knob fits securely onto the timer shaft, and it allows for the selection of the desired drying cycle and time.

Color: White with Blue Trim

Cap Sold Separately

Over time, wear and tear, excessive force when turning, or accidental impact can cause the timer knob to crack, loosen, or lose its grip on the timer shaft. This makes it difficult to select and maintain accurate drying cycles.

Symptoms of a faulty Dryer Timer Knob include:

• Difficulty turning the knob to select the desired cycle
• Knob slipping or turning loosely
• Cracks, breaks, or missing parts

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This washer clothes mover is the upper portion of the agitator assembly.

This hinge retainer plate secures the appliance door hinge to the cabinet or door, keeping alignment and smooth operation. Replace a bent, stripped, or missing plate to stop hinge wobble and help the door close and seal properly.

• Anchors the door hinge and distributes load to prevent shifting
• Maintains proper door alignment and gap for smooth opening/closing
• Helps prevent door sagging, rubbing, or poor gasket sealing
• Typical symptoms include a loose hinge, wobbly door, or door not closing flush

• Disconnect power and support the door before removing any hinge fasteners
• Mark hinge locations to preserve alignment during reassembly
• Install the plate in the correct orientation; transfer any spacers/shims in original order
• Tighten fasteners evenly, then verify door alignment and gasket seal

The lid hinge bearing is used for the lid hinges on washers and dryers. When functioning properly, it allows the lid to open and close properly. If this is a problem with the bearing, it could make the lid difficult to move. In some cases, when the lid will not close, it means that the machine will not function correctly. Damaged lid hinge bearings should be replaced as soon as possible.The lid hinge bearings see a lot of work since they are in use whenever the lid of the washer or dryer opens and closes. They could become cracked and broken over time. Replacing the bearings is a relatively simple repair that owners can make on their own.This lid hinge bearing is for use with many models of washers and dryers from Whirlpool, KitchenAid, Roper, Estate, Inglis, Maytag, Admiral, Amana, Crosley, and Magic Chef. This is a genuine OEM replacement part that has been sourced from the manufacturer. The piece is sold individually, so if owners need to replace more than one hinge, they will need to buy multiples.

Size: 5 foot long. Rubber fill hose used on most automatic washing machines. Two hoses used per machine.

The Hose is an OEM part for Whirlpool washing machines. This hose is responsible for transporting water from the washer tub to the drain pump and then out to the external drain during the drain cycle. 

Causes of a bad drain hose can include regular wear and tear, blockages from debris, or cracking and splitting due to age and repeated use. 

Symptoms of a bad hose include:

• Water leaking from the washing machine during or after a cycle
• Slow or incomplete draining of water
• Visible cracks, splits, or other damage on the hose
• The washing machine stopping mid-cycle due to drainage problems

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This drum baffle is the internal clothes lifter for select 3.6-cu ft front-load washers. It helps tumble and separate laundry, improving wash action and preventing items from staying flat against the drum.

• Guides and lifts clothes as the drum rotates for better turnover and cleaning
• A damaged or missing baffle can cause poor wash performance or unusual tumbling noise
• Loose baffles may rattle or snag items during cycles
• Restores proper drum agitation and fabric movement

• Unplug washer and turn off water before servicing
• Access is typically from inside the drum; rotate drum to align and release/secure the baffle
• Reuse existing hardware if no new fasteners are provided
• The baffle is fully locked/secured before running a test cycle

The Water Valve is an OEM part for Whirlpool washing machines. It is responsible for regulating the flow of incoming water into the washer.

During cycles, the water valve opens and closes at timed intervals to admit the proper amounts of hot and cold water into the tub. It works in conjunction with other components like the water level sensor to fill the tub to the needed depth for each wash program.

Causes of a faulty valve can include mineral deposits clogging internal filters and sensors over time. Mechanical damage from rough handling may also impact performance.

Symptoms of a bad water valve include:

• Inability to select water temperature options
• Erratic or incomplete water filling of the tub
• Fluctuating water levels during cycles
• Persistent error codes related to water issues

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Refrigerator Drain Connector is an OEM part for Whirlpool refrigerators. It is responsible for directing water and condensation from the evaporator fan coil and defrost into the drain pan. 

Causes of a bad drain connector can include cracks, breaks or deformations caused by repeated thermal cycling or impact damage. Mineral or lime buildup inside the connector over many years can also restrict water flow.

Symptoms of a bad drain connector include:

• Water or condensation leaks around the connector area 
• Puddles or watermarks on the floor behind the fridge
• Slow drainage of water from the evaporator fan coil
• Mold or mildew growth near the connector or drain area

This replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This rear panel support is the structural bracket that secures the appliance's rear cover/backguard in place. Replacing a worn or broken support restores proper alignment, helps protect internal components, and reduces vibration noise.

• Secures the rear panel/backguard to the chassis for stable, proper fit
• Maintains alignment of panels and mounting points
• Helps minimize vibration, flexing, and rattles from a loose rear panel
• Common signs of failure: cracked or missing bracket, stripped mounting points, panel movement or buzzing

• Disconnect power at the breaker; shut off gas supply
• Pull the appliance forward carefully to access the back; protect flooring
• Remove fasteners, replace the damaged support, and reuse original hardware/clips
• Keep wiring clear of sharp edges; tighten screws evenly without over-torquing and check for vibration before repositioning

The Detergent Drawer is an OEM part for Whirlpool washing machines. This drawer holds and dispenses detergent, fabric softener, and bleach into the washer at the appropriate times during the wash cycle.  

Causes of a bad detergent drawer can include buildup of detergent residue, damage from overloading, or general wear and tear.

Symptoms of a bad detergent drawer include:

• Detergent not dispensing properly
• Drawer difficult to open or close
• Leaks from the detergent drawer area
• Visible cracks or damage

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Water-Level Pressure Switch is an OEM part for Whirlpool washers. It is responsible for monitoring the water level inside the washer's tub during different cycles. This switch detects changes in air pressure as the water level rises or falls, communicating these variations to the washer's control board. 

Symptoms of a faulty water-level pressure switch include:

• Incorrect water levels during the wash cycle
• Washer not filling or draining properly
• Error codes related to water level

A bad water-level pressure switch can occur due to various factors, such as clogs or blockages in the air hose, a malfunctioning switch mechanism, or electrical issues. If you notice problems such as the washer not filling or draining properly, water levels that are too high or too low, or error codes related to water level, it may be time to replace the water-level pressure switch.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

This replacement part is intended to replace a broken or defective gear case in washing machines.The gear case rotates the washing machine's basket by driving the agitator. The user may notice the basket does not spin efficiently, if at all, and this the gear case may need to be replaced. Before any repairs are made, the washing machine should be entirely disconnected from the power and water sources. It's recommended that work gloves are worn to ensure proper protection. This is a genuine OEM part made by Whirlpool and has been sourced directly from the manufacturer. As an authentic replacement part, this gear case is suitable for installation in multiple different models of washing machines that have been manufactured by Whirlpool, Kitchenaid, Maytag, and various other brands. This is a genuine part made of high-quality, durable materials and is sold individually.

This bleach dispenser for a washing machine holds liquid bleach and releases it into the tub at the appropriate point in the cycle, helping dilute bleach and protect fabrics from contact with undiluted solution. What it does:

• Holds and meters liquid bleach until the machine calls for dispensing
• Helps ensure bleach mixes with water for even, diluted distribution
• Replace if cracked, clogged, or leaking
• Common symptoms include bleach not dispensing, bleach left in the cup, leaks around the dispenser area, or bleach spots on fabrics

• 1 bleach dispenser

• Disconnect power and turn off water before servicing
• Access and mounting vary by model; follow your service manual to reach the dispenser
• Detach hoses/clamps or fasteners, transfer any reusable hardware, and seat the new dispenser fully
• Reconnect, then run a test fill/rinse to check for proper dispensing and leaks

Rubber grommet for motor mount stud.