Amana Washer Parts

Rubber grommet for motor mount stud.

This washplate restores the washer's wash action. It mounts to the drive hub and rotates to move water and fabrics, helping resolve slipping, no-agitation, and poor cleaning when the original plate is worn, stripped, or cracked.

• Engages the drive hub to create the low-profile agitation that moves clothes and water
• Replaces a stripped, cracked, or rounded washplate that slips on the hub
• Common symptoms include clothes not moving, poor cleaning results, clicking/grinding during wash, or an impeller that spins freely by hand
• Also referred to as a low-profile agitator or impeller

• Disconnect power and turn off water before servicing
• Lift the lid, remove the center cap, then remove the center bolt to lift off the old washplate
• Clean and inspect hub/splines; align and fully seat the new washplate before reinstalling the bolt and cap
• Run a test cycle to ensure proper agitation and operation

This standpipe adapter connects the washer's drain hose to a household standpipe for a secure, stable fit. It helps ensure proper drainage and reduce leaks or hose movement during operation when installing or refreshing the drain connection.

• Adapts the washer's drain hose for standpipe installations
• Helps keep the hose seated to minimize leaks, kinks, or pull-outs
• Supports a proper air gap to reduce siphoning when installed correctly
• Common symptoms: water at the standpipe, hose popping out, drain-back after a cycle, or improper draining

• Disconnect power and turn off water before working behind the unit.
• Place a towel to catch residual water from the drain hose.
• Slide the adapter onto the hose end, insert into the standpipe, and secure per the manufacturer's instructions.
• Ensure the hose isn't kinked and test a drain/spin cycle to check for leaks.

This thrust ring is a small spacer that controls end-play on a shaft or gear, keeping parts aligned and reducing friction. Replacing a worn ring restores smoother, quieter operation and helps prevent premature wear in the assembly.

• Maintains axial spacing and limits end-play in rotating assemblies
• Reduces friction and metal-to-metal contact between components
• Helps stabilize shafts/gears to minimize noise and vibration
• Replace if you notice scraping/grinding sounds, wobble, or visible wear on the old ring

• Disconnect power before servicing
• Refer to your model's parts diagram to confirm orientation and stack order with any spacers/washers
• Clean the shaft and mating surfaces; replace any companion parts that show severe wear
• After reassembly, check for smooth rotation and proper end-play before returning to service

This part is a genuine OEM replacement drive motor. It is intended to replace a broken or faulty motor in various washers.This motor drives the washing machine, allowing the drum to rotate and agitate when the user selects the desired settings. Over time, the motor might become worn or start to malfunction, requiring immediate replacement. Before starting the repair process, unplug the appliance from the power source and check the resistance running through the motor windings using a multimeter. If the meter measures infinite resistance, the drive motor will definitely need to be replaced. Work gloves should be worn to prevent injury.This part has been made by Whirlpool and has been sourced directly from the manufacturer. This part is made out of high-quality, durable, non-corrosive materials to ensure high quality and is sold individually. It is compatible with washing machines manufactured by Whirlpool, Maytag, Jenn-air, and various other brands.

This replacement main bearing assembly supports the washer's drive/spin system. It keeps the inner basket and drive shaft rotating smoothly and quietly, helping maintain alignment and reducing vibration during wash and high-speed spin.

• Supports and centers the spin basket/drive shaft for low-friction rotation
• Helps reduce noise and vibration when spinning at high RPMs
• Restores smooth operation when the original bearing is worn or rough
• Common symptoms: roaring/grinding during spin, basket wobble/play, roughness turning by hand, possible leak at rear center if related seal wear is present

• Disconnect power and water before service; allow the appliance to cool
• Access and replacement procedures vary by model; significant disassembly is typical
• A bearing press/driver may be required; inspect shaft and related seals and replace if worn
• After reassembly, run a test spin to check for leaks

STACK KIT FOR LONG VENT DRYER

The Shipping Bolt Kit is an OEM part for Whirlpool washing machines, specifically designed to secure the appliance during transport. This kit includes several bolts that are crucial for immobilizing the washing machine's drum, preventing any movement that could lead to internal damage while the unit is being moved. This kit includes two front and two rear shipping bolts

Causes for replacing the Shipping Bolt Kit can stem from misplacing the original bolts after installation or the bolts becoming worn or damaged after multiple uses.

Symptoms of needing a Shipping Bolt Kit include:

• Preparing a washing machine for a move without the original bolts, risking damage to the unit
• Noticing previous shipping bolts are lost or damaged, requiring replacement for future transport

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Door hinge, right hand. For left hand hinge order WP3387559

The Water Level Switch is an OEM part for Whirlpool washers. It is responsible for monitoring and controlling the water level during the wash cycle, ensuring the appropriate amount of water is used for each load.

A bad water level switch can occur due to electrical issues, component failure, or physical damage. If you notice problems such as incorrect water levels, overflowing, or insufficient water in your washer, it may indicate a problem with the water level switch.

Symptoms of a bad water level switch include:

• Incorrect water levels, either too high or too low
• Washer overflows or fails to fill with water
• Insufficient water for proper cleaning or rinsing

Replace your faulty water level switch with this genuine OEM part to restore your washer. 

This Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

This adapter tube assembly connects sections of the appliance's water line to create a secure, leak-resistant path for water flow. Replace it if the tube is cracked or the connection no longer seals properly to prevent leaks and restore flow.

• Connects water tubing between components within the appliance's water system
• Helps maintain a tight, leak-resistant seal at the joint
• Restores proper water flow when a tube or connector is damaged
• Typical symptoms: water leaking at the connection, reduced or no water flow, visible cracks/kinks, loose fit

• Disconnect power and shut off the water supply before servicing
• Relieve line pressure and place a towel or pan to catch any residual water
• Note routing and orientation before removal to ensure correct reassembly
• After installation, restore water and check all connections for leaks

The rubber foot is an OEM replacement part for Whirlpool washing machines. This small but essential component fits beneath the leveling legs, providing stability and preventing the appliance from moving or vibrating excessively during operation. It also protects flooring surfaces from potential scratches or damage.

Symptoms of a bad Leveling Leg Pad include:

• Increased vibration or noise during the wash or spin cycle
• The washing machine wobbling or becoming unsteady
• Visible wear, cracks, or damage to the pad

Causes of a failing Leveling Leg Pad can include wear and tear from prolonged use, exposure to moisture, or excessive weight causing deformation. Replacing worn pads helps maintain the appliance's balance and efficiency.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

For the leveling leg order W10176519.

Leg, adjustable (w/nut)

This drum baffle mounts inside the rotating drum and lifts items so they tumble evenly through the cycle. Replace a cracked, loose, or missing baffle to reduce noise and restore consistent tumbling performance. What it does:

• Lifts and separates laundry as the drum turns for even tumbling
• Helps prevent clumping that can lead to poor results or longer cycles
• Maintains balanced drum movement; damage or looseness can cause rattling or scraping
• May help if items aren't tumbling well, you hear thumping, or garments snag inside the drum

• 1 drum baffle

• Disconnect power before servicing; for gas dryers, also shut off gas. For washers, turn off water supply.
• Open the door and rotate the drum to access the baffle's mounting screw(s).
• Remove the screw(s), disengage the baffle from its slots, and lift it out.
• Seat the new baffle in the slots and secure with the screw(s). Hand-spin the drum to confirm clearance before use.

This door-mounted dispenser stores detergent and rinse aid and releases them at the right time in the cycle to help deliver clean, spot-free dishes. Replace a broken, leaking, or jammed dispenser to restore proper detergent release.

• Holds detergent and rinse aid and dispenses them during the wash cycle
• Supports consistent cleaning performance by timing chemical release
• Detergent cup won't latch or open
• Rinse aid doesn't dispense or leaks from the dispenser
• Detergent remains in the cup after the cycle

• Disconnect power and turn off the water supply before servicing
• Remove the inner door panel to access the dispenser
• Disconnect the wire harness, release locking tabs/fasteners, and install the new unit flush to the door
• Clean the sealing surface; tighten fasteners evenly and run a test cycle to check for leaks and proper dispensing

This hinge cover is a small trim piece that conceals the door hinge and mounting screws. Replace a cracked or missing cover to restore a clean, finished look and help keep lint and debris out of the hinge cavity.

• Covers and protects the door hinge and screw heads
• Restores a smooth, finished appearance around the hinge opening
• Helps shield the hinge pocket from lint and debris
• Common replacement when the original cover is cracked, missing, or loose

• Disconnect power; for gas units, also shut off the gas supply
• Support the door; loosen/remove hinge screws as needed to access the cover
• Remove the damaged cover; position the new cover and secure per model design
• Verify door closes and aligns properly before returning to service