Craftsman Gasket & Seal

The Lower Door Seal is an OEM part for Bosch dishwashers. It plays a crucial role in preventing water from leaking out of the dishwasher door during cycles. This seal is positioned along the bottom of the door, ensuring a tight and secure closure that keeps water contained within the unit.

Causes of a bad Lower Door Seal may stem from various factors. These include natural wear and tear due to extended use, chemical degradation caused by harsh detergents, physical damage like tears or cuts, as well as improper installation or alignment.

Symptoms of a bad Lower Door Seal include:

• Water leaking from the bottom of the dishwasher door
• Visible signs of wear or damage on the seal
• Mold or mildew buildup on the seal due to constant moisture exposure

This OEM Bosch part can also be used on Thermador and Gaggenau appliances.

The Pump to Sump Gasket is an OEM part for Bosch dishwashers. It serves as a seal between the dishwasher's pump and the sump, preventing water leaks during the washing cycle. This gasket is essential for maintaining the integrity of the dishwasher's internal components, ensuring that water flows where it's supposed to go without causing damage to the machine or your home.

Causes of a malfunctioning Pump to Sump Gasket can stem from normal wear and tear, as repeated exposure to water and detergent can degrade the gasket over time. Improper installation may cause the gasket not to seal properly.

Symptoms of a bad Pump to Sump Gasket include:

• Water leaking from underneath the dishwasher.
• Signs of water damage or corrosion around the pump or sump area.
• Unusual noises during operation, which may indicate water is seeping into areas it shouldn't.

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

The Burner Gasket is an OEM part for Bosch cooktops and ranges. It provides a seal between the burner and the cooktop surface, preventing gas leaks and ensuring efficient operation.

Causes of a bad burner gasket can include wear and tear from frequent use, exposure to high temperatures, or damage from cleaning activities. Over time, the gasket may become brittle or develop cracks, compromising its sealing ability.

Symptoms of a bad burner gasket include:

• Gas odors near the cooktop
• The burner not igniting properly
• Visible cracks or deterioration in the gasket
• The burner not sitting securely in place

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This factory washer is used in appliance assemblies to distribute load under a fastener and maintain a secure, accurate fit. Replace a missing or damaged washer to restore proper stack-up and reduce vibration, noise, or loosening.

• Distributes load and provides proper spacing in the fastener assembly
• Helps keep bolts, screws, or nuts tight to minimize vibration and rattling
• Direct replacement when the original washer is worn, bent, cracked, or missing
• Typical signs include loose panels/brackets, recurring looseness after tightening, or new vibration after service

• Unplug the appliance; shut off water supply if working near hoses or valves
• Note the original hardware stack-up and reassemble in the same order
• Inspect mating surfaces and companion hardware; replace any damaged parts
• Tighten fasteners snugly per service guidance; avoid overtightening

A carburetor gasket is a thin rubber material that provides a seal between two parts. Its primary purpose is to prevent fuel and air leaks. This gasket is installed between the air cleaner and the carburetor. Over time, it can crack and tear due to heat and fuel exposure. When this happens, the carburetor may produce the wrong combustible mixture for the engine. In return, the engine may experience rough idling and flooding. A carburetor gasket replacement is necessary. MTD makes this carburetor gasket replacement. It is manufactured to fit string trimmer, leaf blower and tiller made by MTD, Bolens, Troy-Bilt, and Craftsman. This brand-new carburetor gasket is sold individually. A fully assembled carburetor and O-ring are sold separately.

These O rings are replacement parts intended for use in a number of gasoline-powered lawn trimmers. The O rings serve as gaskets and are placed at the entry and exit points in the carburetors where gasoline and air are mixed and the expansion powers the trimmer. Though constructed of durable material, periodically the flow of the air/fuel mix or the rush of expanding air will cause damage to occur to the O rings so they become less resilient and the carburetor functions less efficiently. In these cases, users often decide to replace not just the element of the carburetor but the O rings as well. Users may notice problems with the carburetor when they cannot get an adequate adjustment, allowing the trimmer to function smoothly. They may also have trouble getting the trimmers to start at all or run without smoking. To replace the O rings, remove the air filter cover and carburetor. Once the carburetor has been cleaned, and the gasket and filter replaced, add a fresh mix of 40:1 fuel. The trimmer should start immediately. These OEM certified O rings are compatible with Bolens, Troy-Bilt, Yard Machines, and Craftsmen trimmers.

This oil seal is found in many different lawn and garden machines on the gearbox, including garden tillers. It is a genuine OEM replacement part sourced directly from the manufacturer. It is designed to prevent water, dirt, and other pollutants from getting inside the gearbox and causing damage or poor performance. The seal also ensures that oil doesn't leak from equipment. Normal wear and tear reduces the functionality of the seals and reduces engine performance as well as causing oil leaks. The oil seal should be inspected and replaced as part of routine maintenance. This repair takes approximately one hour. A socket set and seal pull are needed. Remove the spark plug wire before working on the equipment. Place tiller on a flat surface and jack up the rear tines. Take the rear tines, wheels, and tires off the machine. Clean the shafts to remove dirt and debris buildup. Remove the damaged seals and clean the part before installing new seals. Install the new oil seal and fill the gearbox with gear lube. Reinstall the spark plug. This is a heavy-duty metal and rubber oil seal sold as an individual unit. It is compatible with tillers manufactured by Troy-Bilt, MTD, Yard Machine, and Craftsman.

This o-ring is a genuine OEM part sourced from the manufacturer for use in many parts of engines in lawn and garden equipment. The o-ring is a type of gasket but is not flat like a gasket. It is circular and made of rubber. It is seated in a groove on the engine part and is compressed against another part to create a seal. This seal keeps air and fluids from entering or exiting the sealed part. Like gaskets, o-rings must be periodically inspected and replaced to ensure proper engine performance.Visual inspection of o-rings will reveal nicks, indentions, cuts, or tears on the surface of the o-ring. If the rubber has warped due to excessive heat, it will not fit properly and will need to be replaced. The replacement may not require tools, depending on the location of the rubber gasket. Remove the bad o-ring and wipe both sides of the area to remove the old grease. Apply fresh grease to the o-ring before installing it to ensure a tight seal. Press the new o-ring firmly in the groove before attaching the connecting part. If the ring does not seat well or has to be stretched to fit, discard and start with a new o-ring.The o-ring is sold individually. It is designed for trimmers and tillers. It is compatible with Craftsman, MTD, Bolens, Troy-Bilt, and Cub Cadet.

This is a cylinder head gasket that is an OEM replacement part sourced directly from the manufacturer for use on lawn mowers and other small engines in outdoor lawn and garden equipment. The head gasket is the engine block that separates the cylinder head from the engine block. This gasket is used to prevent oil from mixing with coolant. The cylinder gasket seal also seals the internal combustion process, putting it under the pressure it needs to operate. If the gasket is worn or cracked and the pressure is not right, the engine will not operate correctly, and there will be a loss of power. Oil leaks are another way to tell that the cylinder head gasket is bad and needs to be replaced. Before deciding if the cylinder head gasket is the problem, a compression test should be run using a compression gauge. After pulling the starter cord, the internal pressure should read 60 psi. If the reading is less than this, the cylinder head has lost compression, and the gasket should be removed and replaced. This cylinder head gasket is sold individually. This gasket is designed for use on lawn mowers and small engines manufactured by MTD, Yard Machines, Troy-Bilt, Yard-Man, Cub Cadet, and Husky.

This seal kit is a genuine MTD part, sold individually. This seal kit provides a variety of replacement seals for use in a log splitter.The seal kit in a log splitter might have to be ordered as a complete replacement part if one or more seals show signs of damage. If the seals in a log splitter allow external materials such as dirt, debris, pebbles, and dust to pass into the appliance or if there are frequent oil leaks stemming from the area of one or more seals, this seal kit should be ordered as a genuine OEM replacement part.This is a genuine OEM replacement part sourced directly from the manufacturer. It is sold individually. This seal kit is compatible with the following outdoor appliance brands: MTD, Craftsman, Cub Cadet, Troy-Bilt, and Yard Machines.

This is a cylinder head gasket that is located between the cylinder head and the engine block on many types of lawn and garden equipment. It is responsible for sealing the internal combustion process. It prevents oil and coolant from mixing together while each moves to the cylinder head from the engine block. If the cylinder head gasket is broken or damaged, it can cause fouled spark plugs, white smoke, milky white oil, leaking coolant, or an overheating engine.Gaskets can crack or wear out over time, which requires the parts to be replaced. Some of the tools needed to make the replacement include a gauge, socket driver, Torx screwdriver, nut driver, screwdriver, torque wrench, hex bit, and spark plug wrench. Make sure to wear work gloves and do the replacement with the tools on a flat surface.This cylinder head gasket is an authentic OEM replacement component that is sourced directly from the manufacturer. It is sold as an individual part. The head gasket is designed for use with lawnmowers, string trimmers, tillers, edgers, log splitters, and wood chippers created by Cub Cadet, Craftsman, and MTD.

The carburetor gasket is installed between the engine and the carburetor body, providing an airtight seal so that all fuel and air going into and out of the carburetor are delivered at optimal pressure for peak engine performance. This gasket can wear down over time and create leaks in the seal, which allows air to escape and can affect the operation of the engine. In the event that the engine won’t stay engaged or isn’t running properly, there may be a problem with the gasket seal. Be sure to let the engine cool completely before working on this part. Drain the gas tank and work in a well-ventilated area. This genuine OEM carburetor gasket replacement will offer an exact fit for compatible lawn and garden equipment engines, including those from MTD, Craftsman, Troy-Bilt, Yard-Man, Husky, and Cub Cadet. This gasket is sold individually as a single part.

A flexible replacement gasket that seals and side lamp glass, cushioning and securing the glass to help block moisture and debris from the lamp housing. Restores a tighter fit and reduces vibration or rattling around the lamp area. What it does:

• Seals the edge of the lamp glass to keep moisture, dust and food debris out of the lamp housing.
• Cushions and centers the lamp glass to reduce vibration and prevent rattling or glass movement.
• Helps maintain a stable lamp assembly so the light cover sits flush and stays in place.
• Use when the gasket is cracked, torn, deformed or missing, or when the lamp glass feels loose.

• Disconnect power to the appliance before servicing to avoid electrical shock.
• Handle lamp glass carefully to avoid breakage; wear gloves and eye protection as needed.
• Seat the gasket evenly around the lamp glass edge and press into the channel until fully seated; avoid stretching or deforming the seal.
• Replace only with the exact OEM part number to ensure correct fit and sealing.

Carburetor gaskets ensure that the space between the carburetor itself and the insulator is properly sealed. This prevents air from seeping into the engine. As time passes, gaskets begin to become worn and crack, which can lead to small air leaks. If the gasket deterioration becomes severe the leaks will worsen. An air leak on an engine can cause vibrations and misfires. Gaskets should be regularly replaced to prevent engine trouble. This carburetor gasket is a genuine OEM part that has been sourced directly from the manufacturer. This carburetor gasket is manufactured from a top-quality composite material. This replacement gasket fits a number of different models of Troy-Bilt and Craftsman lawn and garden equipment. Please note these gaskets are sold individually.

The carburetor gasket plate creates a seal between the air cleaner base and the carburetor body. This plate is made of durable material but it is exposed to constant pressure and heat, which can cause it to degrade over time. It can also become damaged or broken, which would require a replacement. If the gasket is degraded or damaged, it could allow air to leak out of the engine, reducing compression and affecting performance. Severe cases could result in total engine failure, which is why replacement should be done as soon as possible. This genuine OEM gasket plate is designed to be used in a variety of log splitters, tillers, and lawn mowers from brands like Yard Machines, MTD, Yard Man, Cub Cadet, Troy-Bilt, and Husky. This carburetor gasket plate is made of durable materials and sold as an individual piece. No hardware is included for this part and will require an additional purchase if needed. Always allow the engine to cool before performing repairs and wear gloves for hand protection.