Crosley Dryer Parts

The very easy diagnosis was motor seizure. Because the machine is about a decade old, I decided to renovate most of the guts. My DIY project included replacing the motor, blower, drum bearing, belt, and door hinge. The end result is a functional dryer with no left-over parts. Lack of parts and hardware challenged the effort. For example, the blower assembly did not have the slide capture for the motor. I had to use the old one which is showing its age. With the exception of the drum... Read more

• No heat or not enough heat

Being a complete DIY I hate to call some unknown person into my home knowing that just to get them there will cost me more than I will spend for parts that I don't need.After all, they are trying to make a living and by selling me parts that I don't need will increase their profits. I've dealt with APP before and was impressed by their site because I could find both mechanical and electrical drawings for almost everything I have. I looked up my dryer, decided what was probably the problem,... Read more

For several months we could smell a slight odor of propane in the laundry room and wondered why, just didn't seem like it was enough to be overly concerned, but thought something must be wrong with the dryer, but it was still working. We just didn't know how inefficiently. Then the extra time it took to dry a load of clothes progressively seemed to get longer, but things still seemed to work fine and the clothes got dried, given enough time. Then approximately 3 weeks ago we noticed the dryer... Read more

• Marks left on clothes

After replacing thermal fuse once and having it fail a second time, I had to dig a little deeper to uncover the problem. I checked for blockage in the vent but everything was clear. I did, however, find that the drum had some up and down play in it. After closer inspection, I could see that the front drum seal was actually worn to the point that I could see a gap between the seal and the drum. I figured that the gap in the seal was letting air in and not letting sufficient air flow through the... Read more

• Door won't close

I chatted with a rep on Appliance Parts Pros and found out which parts I needed for my model of dryer. Ordered the 2 clips that held the door closed. They arrived the next day!! My dryer was very different than the video but we were able to figure out which screws to remove. The old clips popped out and the new ones popped in. Took about 30 minutes because of there being a top and bottom clip to remove and replace and line up the door parts to screw the screws back in. It works great!! I... Read more

Removed and replaced parts about 30 minutes of work. No leaks Read more

Watched You tube videos to narrow the problem down to old deteriorated gaskets. Read more

Touch up paint Read more

The dryer is a Kenmore Laundry Center, model 417-99570150. Bought in 1998, so it is an older model. Not wanting to buy the newer ones that are out now. We opted to fix the Kenmore. Just believe the older models are worth fixing, if at all possible. Frist we had to figure out what parts we would need and if the cost would be worth our time. I went on YouTube: and type in Kenmore dryer not turning on. Watched several videos to narrow down the possible problem. Next step was to... Read more

Ordered the parts from ApplianceParts Pros.com and saved the $100 service call. The fix was easy, complete instructions enclosed. Read more

• Shakes and moves

REPLACING THE SUSPENSION PADS AND REPLACE THE BALNCE RING EVEN IF MY DIDN'T LEAK ANY FLUID OUT OF IT... IT SOLVE THE PROBLEM, IT WORKS BETTER NOW THAN IT EVER DID, THE ONLY THING I COULD COME WITH IS THE MANUFACTURE PUT THE WRONG BALANCE RING IN IT TO START WITH... MY IS A 400 KENMORE TOP LOADER, IT IS THE EASIES WASHER I HAVE EVER TAKEN A PART.. I WISH CARS WERE THAT EASY... IT TOOK ME OVER A MONTH FIGHTEN THIS PROBLEM UNTIL I FOUND IT ON YOUTUBE... WHAT BLESSING IT WAS... Read more

Replaced It With New One Read more

Disassembled dryer. Installed new belt, drum rollers, idler arm and blower. Read more

Went on YouTube and found out how to replace switch. Had it replaced in no time. Read more

• No heat or not enough heat
• Takes too long to dry

Since finding out pulley on motor is factory installed, I had to order a new motor with new pulley on it. I could not remove old blower wheel from old motor, no matter how hard I tried so I had to purchase new blower wheel and new blower housing. I am super happy finding Appliancepartspros.com the prices, and my experience was great! I basically removed everything step by step, and then replaced with the new parts step by step. I had help by watching videos that were provided online before and... Read more

Replaced the thermal fuse and the heating element. It took about 15 minutes to diagnose using a multimeter. The shipping was super fast! It took 15 minutes to install. Read more