Crosley Refrigerator Parts

This dispenser drip tray sits beneath the refrigerator's ice/water dispenser to catch drips and small spills, helping keep the area cleaner and reducing moisture on the door and surrounding surfaces.

• Collects water and ice drips under the dispenser
• Helps contain minor spills during dispensing
• Protects the door surface from moisture and staining
• Common signs of wear: cracked or missing tray, water pooling in the dispenser area, tray not sitting flush

• Disconnect power before working around the dispenser area
• Lift the old tray straight up and out of the recess
• Clean and dry the dispenser pocket to remove residue
• Align and press the new tray down until it sits flat and secure

This door-activated light switch controls the interior lamp in your refrigerator. Replace a worn or sticking switch to restore dependable lighting and prevent the bulb from staying on and warming the compartment when the door is closed.

• Opens and closes the light circuit as the door is opened and closed
• Helps prevent the light from staying on with the door shut
• Common symptoms: interior light won't turn on, stays on with the door closed, or works intermittently
• Physical signs may include a stuck/broken plunger or damaged housing

• Disconnect power before servicing
• Gently pry the old switch from the liner/panel and release its locking tabs
• Transfer wires one at a time to the same terminals on the new switch
• Press the new switch fully into place; restore power, and test

This evaporator defrost heater melts frost from the evaporator coil during the automatic defrost cycle to restore airflow and stable temperatures. Replacing a failed heater helps prevent ice buildup that restricts cooling and leads to warm spots. What it does:

• Heats the evaporator coil to clear frost/ice during defrost
• Helps maintain proper airflow between freezer and fresh food sections
• Typical symptoms: heavy frost on the back panel/evaporator, weak cooling or rising temperatures
• Also cause evaporator fan noise from ice contact and longer run times

• 1 evaporator defrost heater

• Disconnect power before servicing; allow any ice to thaw
• Access the heater behind the freezer's rear panel; avoid damaging fins or refrigerant lines
• Secure the heater and route wires exactly as original, keeping them clear of the fan and sharp edges
• Restore power and verify the defrost cycle per the service procedure

GRILLE/KICKPLATE

This is the complete ice container assembly for the dispenser. It stores ice and drives cubes to the chute so your dispenser can deliver ice reliably and without jams.

• Holds finished ice in the freezer and feeds it to the dispenser
• Integrated auger moves and helps break up ice for consistent dispensing
• Common failure signs: ice not dispensing, auger not turning, loud grinding, or cracked/leaking bucket
• Restores proper in-door ice dispensing performance

• Unplug the refrigerator and remove the ice bin from the freezer door or shelf
• Transfer any remaining ice to a cooler; let any frost melt to avoid damage
• Align the drive coupling and slide the new bin fully into place
• Restore power and test ice dispense for cube and crush functions

This gray door gasket restores a tight seal around the freezer door opening so cold air stays in and warm, humid air stays out—helping maintain proper temperature and reduce frost buildup when the original seal is worn or damaged. What it does:

• Seals the perimeter of the freezer door to prevent air leaks
• Helps minimize frost/ice accumulation and moisture around the door
• Supports consistent interior temperatures and performance
• Common signs of failure: tears, warping, gaps, frost buildup, sweating/condensation, and poor door sealing

• 1 gray door gasket

• Unplug the appliance before servicing
• Warm the new gasket (soak in warm water or gently heat) to relax folds for easier installation
• Install starting at the corners; ensure the gasket fully seats in the retainer all the way around
• After installation, check seal tension around the door; use low heat to help the gasket conform if needed

This drain hose carries water away from your appliance during draining to help prevent backups and leaks. Replace a cracked, clogged, or kinked hose to restore reliable water removal and protect surrounding floors and cabinets. What it does:

• Directs drain water from the outlet or pump to the designated discharge point
• Maintains proper flow; kinks or blockages can cause slow or no draining
• Helps prevent leaks from splits, pinholes, or loose connections
• Common signs: standing water, water under/around the unit, drain-related error codes, or odors

• Includes 1 drain hose

• Disconnect power and shut off water supply before servicing
• Place towels or a shallow pan to catch residual water when removing the old hose
• Note the original routing; seat connections fully, secure with clamps, and avoid sharp bends or kinks
• Run a brief drain/rinse and check all joints for leaks

This refrigerator door closer restores smooth, positive door action. When worn, the door can click, bind, or swing open. Replacing it helps the door seal properly to maintain temperatures and limit frost or moisture.

• Provides cam action at the bottom hinge for smooth opening and a positive close
• Helps pull the door shut during the last inches of travel to maintain gasket contact
• Typical wear symptoms: popping/clicking at the lower hinge, door that won't stay closed, or poor sealing
• Visual clues include flat spots, grooves, or cracks on the cam surface

• Disconnect power and remove items from the door for safety and to reduce weight
• Lift the door off the bottom hinge; transfer/install the closer in the same orientation as the original
• Reassemble, then verify the door self-closes and the gasket seals evenly
• Use care not to pinch or distort the door gasket during reinstallation

This is the drive gear for the ice maker module. It transfers motor power to the ejector/harvest mechanism so cubes release consistently; worn or stripped teeth can cause clicking, stalls, or little to no ice production.

• Transfers motor torque to rotate the ejector and complete the harvest cycle
• Replaces a cracked, stripped, or worn gear that prevents proper ice ejection
• Typical symptoms: no ice production, icemaker stuck mid-cycle, clicking or grinding from the module
• Helps restore reliable ice maker cycling

• Unplug the refrigerator before service; turn off the water supply if moving the icemaker
• Remove the icemaker assembly for access; note the original gear's orientation before removal
• Align the new gear with the shaft; do not force it—inspect mating parts for wear
• After reassembly, verify the ejector turns freely; restore power and run a test cycle

This ice crusher blade (#2) mounts in the freezer's ice bucket assembly. It helps break up cubes for the Crushed Ice setting and can restore smooth dispensing when the original blade becomes bent, dull, or broken.

• Mounts inside the ice bucket crusher to slice/crush cubes when Crushed Ice is selected
• Helps maintain consistent ice flow and size through the dispenser
• Wear or damage may lead to no crushed ice, only whole cubes dispensing, jamming, or grinding noises
• Visible bending, dull edges, or a missing blade are common failure signs

• Disconnect power and remove the ice bin from the freezer
• Disassemble the crusher housing to access the blades; note the order/orientation of blade #1 and blade #2 before removal
• Wear cut-resistant gloves—edges are sharp
• Reassemble in the same order, tighten fasteners, reinstall the bin, and test the dispenser

This is a replacement power cord that supplies electrical power from a wall outlet to your appliance. A fresh cord helps ensure safe, reliable power delivery when the original is damaged, overheated, or worn.

• Delivers household power to the unit's main electrical connection
• Replace if the cord is cut, cracked, burnt, loose, or intermittently powers the appliance
• Helps resolve issues like no power, tripping breakers, or visible cord damage

• Unplug the appliance and turn off the circuit breaker before starting
• Verify outlet type and cord routing match your original installation
• Transfer any cord clamp/retainer as needed and secure against sharp edges
• Inspect for proper grounding and test operation before returning to service

This ice compartment door closes off the ice storage area inside the freezer, helping contain cold air and keep ice clean. Replace a cracked or warped door to restore a proper seal and easy access to the bin.

• Covers the ice compartment opening to help maintain temperature around the ice bin
• Hinged panel provides convenient access to the ice container
• Helps minimize frost and moisture at the compartment opening
• Common signs it's needed: cracked/missing door, broken hinge tabs, won't stay closed, frost buildup, or ice clumping near the opening

• Disconnect power to the refrigerator before servicing
• Remove screws, pins, or clips securing the old door; note hinge orientation
• Transfer any reusable hinge pins, latches, or trim from the original if required
• Install and align the new door; confirm smooth operation and a tight closure

This dispenser drip tray sits at the base of the refrigerator's ice/water dispenser. It catches small drips and splashes to help keep the dispenser recess and door front cleaner and drier. What it does:

• Collects minor drips and splashes from the ice and water dispenser
• Helps protect the door finish and surrounding area from moisture
• Replace if the tray is cracked, warped, stained, or missing
• Common signs include water pooling in the dispenser recess or a loose, ill-fitting tray

• 1 dispenser drip tray

• Pull the old tray straight out of the dispenser recess; no tools are typically required
• Clean any mineral deposits or debris in the recess before installing the new tray
• Align and seat the new tray flat and flush in the opening
• Disconnect power and shut off water

This refrigerator water tube carries fresh water between the valve, reservoir, dispenser, and/or ice maker. Replacing a cracked or kinked tube restores proper water flow and helps stop leaks inside or behind the refrigerator.

• Directs pressurized water between components in the refrigerator's water system
• Common failure signs: leaks, visible cracking, kinks, or pinhole sprays
• May cause no or slow dispenser flow, or an ice maker that doesn't fill
• Restores correct routing after tubing becomes brittle or damaged with age

• Unplug the refrigerator and shut off the household water supply before servicing
• Place a towel under connections and dispense water to relieve line pressure
• Depress quick-connect collars or loosen clamps to remove the old tube; route the new tube exactly like the original
• Fully seat tubing in fittings, perform a gentle tug test, restore water, check for leaks, and flush several cups to clear air

This limit switch monitors a set condition and opens or closes its contacts when that limit is reached. Replacing a failed switch restores proper safety cutoff and consistent operation of the appliance's heating or movement system. What it does:

• Senses a limit condition at its mounting point (such as temperature or travel/position, depending on model)
• Changes state at a defined threshold to protect components and wiring
• Interrupts power to heat or motor circuits, or signals a control to respond
• Common failure signs: no heat or shuts down early, runs continuously, won't start, or intermittent operation

• 1 limit switch

• Disconnect power to the appliance before servicing
• Note wire positions; transfer connectors one at a time or take a photo for reference
• Reinstall in the original orientation so the actuator or sensing surface contacts the correct area
• Address root causes (blocked airflow, binding mechanisms, shorted components) to prevent repeat failures

This dispenser module controls the refrigerator's ice and water dispensing functions and user interface. Replace a failed module to restore responsive dispensing, indicator lights, and consistent operation at the dispenser.

• Interprets button/paddle inputs and manages dispenser functions
• Coordinates ice and water dispensing operations
• Controls dispenser indicator lights/display for user feedback
• Failure can cause no dispense, unresponsive controls, or erratic/loss of lights

• Disconnect power and shut off water supply before service
• Remove the dispenser trim/panel carefully to access the module; protect against static discharge
• Note wire positions; transfer connectors and any reusable covers/overlays from the original part if applicable
• Restore power and test ice and water dispensing after installation