Dishwasher Knob, Dial & Button

The Toaster Lever is an OEM replacement part for Whirlpool brand toasters. This lever allows for control of the toast lowering function. It measures about 1 inch wide by 1/2 an inch high by 1-1/2 inches deep.

Causes of a bad lever include wear and tear over thousands of use cycles, stress fractures from overly forceful movement, or damage at the pivot point inhibiting smooth motion.

Symptoms of a bad lever include:

• Difficulty lowering or lifting bread fully
• Requires two hands or excessive force for operation
• Loose, wobbly feel when engaging the lever
• Broken or missing edge guards exposing sharp surfaces

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore models.

The Button is an OEM component specifically designed for select Bosch dishwasher control panels. It initiates cleaning cycles upon end-user selection.

Reinforced polymer caps withstand millions of presses without cracks or splits. Gold-plated contacts provide dependable electrical pathways starting wash sequences. 

Causes requiring replacement commonly relate to prolonged use over decades of wearing through water-resistant barriers. Direct impacts could also unsettle attachment boards necessitating full assembly swapping.

Symptoms  of a bad button include:

• Failure to register selections or improperly engaged cycles  
• Loosened fasteners no longer securely mount interface points
• Cracked or distorted housings exposing internal switch mechanisms

Note: In some cases, the buttons are not all the same and it matters which location/order you put them.

This OEM Bosch replacement button is also compatible with Thermador, Gaggenau, and some Kenmore dishwashers relying on electronically controlled sequences. Proper installation restores intended cycle initiation capabilities.

The Button is an OEM part for Bosch dishwashers. It serves as a component of the control panel, allowing users to select various wash cycles, options, and settings for operating the dishwasher.

Causes of a malfunctioning Button can include physical damage from impact or excessive force when pressing, as well as general wear and tear over time. 

Symptoms of a bad Button include:

• Unresponsive or stuck buttons, making it difficult to change settings
• Certain dishwasher cycles or options not engaging correctly
• Worn-out or faded button labels or markings, making them hard to read

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

The On/Off Button is an OEM part for Bosch dishwashers. As a primary control interface, this button facilitates the activation and deactivation of the dishwasher's functions. Its ergonomic design and precise construction ensure ease of use and reliable operation.

A common issue with a malfunctioning On/Off Button involves wear and tear, leading to a loss of responsiveness or failure to engage/disengage the dishwasher's functions.  

Symptoms of a defective On/Off Button may include:

• Unresponsive or non-functional button
• Difficulty in starting or stopping the dishwasher
• Visible damage or wear on the button's surface

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This is a button. This is a genuine OEM part made by Bosch and has been sourced directly from the manufacturer. This part is intended to replace a broken or defective button on certain different makes and models of dishwashers.This button attaches to the front panel of the dishwasher and is needed for powering on and off the dishwasher. Over time and with regular use, buttons can become worn or broken and stop working. This part requires proper tools for replacement. Before starting, disconnect the dishwasher completely from both power and water hookups. Please follow appropriate safety precautions when attempting to repair any appliances. For more accurate information on how and where to install this button, the appropriate owner's manual and included diagrams should be referred to.As an authentic replacement part, this button is suitable for use on several different models of dishwashers manufactured by Bosch, Thermador, and Gaggenau. Please note that this is a genuine part made of high-quality, durable materials and is sold individually.

This start button is the user-pressed cap on the control panel that engages the underlying switch to begin a cycle. Replace it to restore proper feel and reliable operation when the original button is cracked, loose, or missing.

• Serves as the Start control on the user interface
• Transfers your press to the control's start switch to initiate a cycle
• Helps address a broken, sticking, or missing start key
• Restores alignment and tactile feedback at the control panel

• Disconnect power to the appliance before servicing.
• Open or remove the control panel/fascia to access the button.
• Release retaining tabs/clips and remove the old button; transfer any small clips/springs from the original if present.
• Align and snap the new button into place, reassemble, and test operation.

This push button set replaces the plastic buttons on the control panel, restoring clean looks and reliable, consistent presses so you can select settings and operate the unit without dealing with sticky, cracked, or missing buttons. What it does:

• Provides the physical button caps that interface with the control board's switches
• Restores proper button travel and tactile feel
• Helps when buttons are loose, stuck, cracked, missing, or difficult to press
• Refreshes worn, faded, or damaged button faces for a cleaner appearance

• One set of control panel button caps

• Disconnect power before servicing
• Access the control panel/fascia to reach the button area
• Remove the old button set; align and seat the new set so actuators engage the switches
• Reassemble and test each button for smooth operation

This timer knob replaces the cycle control knob on select dishwashers. It mounts to the timer shaft so you can choose wash cycles; a cracked or stripped knob can make the timer difficult to turn or impossible to set.

• Mounts on the timer shaft to set and advance dishwasher cycles
• Replaces a broken, cracked, stripped, loose, or missing knob
• Helps when the timer won't turn by hand or the knob slips on the shaft
• Restores normal feel and alignment of the front-panel control

• Disconnect electrical power at the breaker before servicing.
• Pull the old knob straight off the timer shaft; do not pry on the console.
• Align the new knob with the shaft and press firmly until fully seated.
• Restore power and verify smooth rotation through all settings.

Color: white. It measures about 2 inches in diameter by 2-1/2 inches deep.

The Push Button is an OEM component specifically designed for select Bosch dishwashers. Installed on the control panel, its durable silicone-coated switch reliably operates cycles. Smooth travel withstands repeated use while maintaining tactile feedback. 

Causes of push-button failure commonly involve contact degradation from steam exposure. Cracks in the silicone introduce debris requiring periodic replacement.

Causes of a bad push button can involve:

• Unresponsive or stuck on cycles 
• Flashing error codes without cause
• Difficulty changing selected options

Symptoms of a faulty push button include intermittent operations as the controller struggles to interpret signals. Replacement ensures trouble-free functionality.

This OEM Bosch part is also compatible with some Thermador, Blomberg, and Miele dishwashers. Replace to retain convenient cycle selection through heavy usage over the appliance's lifetime.
 

Color: Black

This Button is the push-button cap for the control panel. It replaces a broken or missing button so you can reliably actuate the underlying switch and select settings as intended, restoring smooth operation and appearance.

• Presses against the internal switch to trigger functions on the control panel
• Restores proper alignment, travel, and tactile feedback when a button is worn or damaged
• Helps resolve issues such as a cracked, missing, loose, or sticking button that won't actuate selections
• Refreshes the look of the control area when the original is marred or deformed

• Disconnect power to the appliance before servicing
• Open or remove the console/control panel as required; release the old button from its clips or retainer
• Transfer any light guides, springs, or seals from the original if present; seat the new button fully
• Reassemble and test all controls for smooth movement and proper actuation

The Push Button Set is an OEM part for Bosch dishwashers. It includes all buttons needed for cycle selection and temperature adjustments on the control panel.

Causes of a bad push button set can include wear from frequent use, moisture exposure compromising electronics, or physical damage from impact or other mishandling.

Symptoms of a bad push button set include:

• Buttons sticking, failing to depress properly, or malfunctioning entirely
• Inability to scroll through cycles or alter wash settings
• Control panel lights/display malfunctioning or unresponsive

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

The Push Button is an OEM component specifically designed for select Bosch dishwasher control panels. It activates cleaning cycles through tactile engagement. 

Reinforced polymer caps endure user-generated pressures without cracking or splitting. Protected circuit pathways respond dependably to indexed presses starting sequences.

Symptoms signaling the need for a new button involve:  

• Failure to register selections hindering engaged cycles
• Loosened fasteners enabling unintended button displacement
• Deformed housings with compromised switches no longer functioning 

Causes requiring replacement usually involve years of wear degrading protective seals. Direct impacts may unsettle attachment boards necessitating full assembly swapping to restore integrity.

This OEM Bosch replacement push button is also compatible with Thermador, Gaggenau, and some Kenmore dishwasher control modules relying on electronically controlled starts. Proper fastening re-enables intended initiation capabilities.

Color: Black

Color: black. It measures about 2-1/2 inches in diameter.