Dishwasher Wire, Harness, Power Cord

The Power Cord is an OEM replacement part for Bosch dishwashers. It supplies electrical current that allows the dishwasher to properly perform cycles. Located at the rear of the appliance, it plugs into a standard three-prong outlet.

Causes for power cord replacement include cracking, splitting, or breaks in the protective insulation over time from repeated bending and stress.

Symptoms of a faulty power cord include:

• Unresponsive or failed cycles indicating no power to operate
• Melted, blackened, or charred areas along the cord housing
• Visible frayed wires or exposed copper filaments

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

The Power Cord is an OEM part for Whirlpool stand mixers. It provides the electrical connection between the mixer and the power source, allowing the appliance to function properly.

A bad power cord can be caused by wear and tear, accidental damage, or electrical issues. If you experience problems such as intermittent power supply, sparks or frayed wires, or the mixer not turning on at all, it may indicate a problem with the power cord.

Symptoms of a bad power cord include:

• Intermittent power supply or loss of power during operation
• Sparks, exposed wires, or fraying along the cord
• Inability to turn on the mixer  

Replace your faulty power cord with this genuine OEM part to restore your stand mixer. 

This Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

This replacement power cord supplies electrical power from the household outlet to the appliance. Swap a frayed, heat-damaged, or loose cord to restore safe, reliable operation and prevent intermittent power loss.

• Delivers AC power from the outlet to the unit
• Common symptoms include no power, intermittent shutoff, tripped breaker/GFCI, burning odor, or visible cuts/fraying
• Replaces cords with cracked insulation, loose/bent blades, or heat discoloration
• Helps maintain proper grounding when installed as originally routed

• Disconnect power and verify the outlet is de-energized before servicing
• Photograph wire routing; transfer connections one at a time to match the original
• Install/secure the strain relief; route the cord away from sharp, hot, or moving parts
• Test for normal operation after reassembly

The Power Cord Kit is an OEM replacement part for Whirlpool dishwashers. It is a 3-prong grounded, 16-gauge cord that includes all the hardware needed for installation. Includes all hardware needed for installation.

Causes of a bad power cord can include normal wear and tear over years of use, accidental impacts or cuts to the wiring, or improper installation that damages components.

Symptoms of a bad power cord include:

• The dishwasher not turning on or completing cycles
• Warm or hot power cords during operation
• Frayed, cracked, or exposed copper wiring

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air, and some Kenmore models.

This line cord supplies electrical power from the wall outlet to the appliance. Replacing a worn, cut, or heat-damaged cord restores safe, reliable power and can help resolve no-power or intermittent operation issues.

• Delivers AC power from the outlet to the unit's electrical system
• Helps correct no-power or intermittent power when the cord is moved
• Ideal replacement for cords with cuts, fraying, or burn/discoloration on the plug
• Supports proper grounding and safe operation when installed correctly

• Disconnect power before servicing; ensure the appliance is fully de-energized
• Match wire routing and connections to the product's wiring diagram; ensure a secure ground
• Use an appropriate strain relief if required by the product to prevent abrasion
• Route the cord away from sharp edges, moving parts, and hot surfaces

This power cord connects your appliance to household electricity, supplying safe, reliable power to its controls and components. Replace a damaged or overheated cord to restore dependable operation and reduce the risk of shorts.

• Supplies AC power from the wall outlet to the appliance's electrical system
• Helps resolve no power, intermittent power loss, or tripped breaker issues
• Replace if the cord is cut, frayed, melted, discolored, or feels hot at the plug
• Restores safe operation when the original plug or insulation is damaged

• Disconnect power at the outlet or circuit breaker before servicing
• Note wire routing and connection points; match the original orientation for hot, neutral, and ground
• Seat the cord properly and secure with the model's required strain relief or clamp to prevent tension on terminals
• Ensure the cord is not pinched and is clear of sharp edges, hot surfaces, and moving parts; test for proper operation

This dishwasher power cord connects your appliance to a standard household outlet. Replace a frayed, damaged, or missing cord to restore a safe, reliable power connection and help prevent intermittent power issues.

• Supplies power from a wall outlet to the dishwasher's electrical connection
• Appropriate when the existing cord shows cuts, fraying, burn marks, or melted insulation
• Supports safe restoration of the factory-style corded installation when specified for your model

• Disconnect power at the breaker before servicing.
• Route through an approved strain relief; connect hot, neutral, and ground to the marked terminals/junction as instructed by the manufacturer.
• Ensure wiring is secured and not pinched; test operation before sliding the unit fully back into place.

This replacement power cord restores electrical connection to compatible Whirlpool appliances, providing a safe physical replacement for a damaged or worn cord. It lets the appliance receive power so it can operate normally. What it does:

• Replaces a damaged, frayed or broken power cord to restore appliance power
• Provides a secure, standard electrical connection at the appliance inlet
• Helps eliminate intermittent power loss, arcing at the plug, or exposed wiring concerns
• Used when the original cord shows visible wear or electrical faults

• One replacement power cord as shown

• Disconnect power at the breaker or unplug the appliance before starting
• Follow the appliance service manual for cord routing and strain relief attachment
• Use basic hand tools; ensure all connections are secure and insulated

The Cord is an OEM replacement part for Frigidaire washing machines. Extending from the rear of the unit, it safely powers the washer through a connection to a wall outlet.

Causes of cord failure are normal wear from frequent coiling and plugging/unplugging motions over the appliance's lifespan. Rodents or sharp edges may also damage the outer jacketing.

Signs of a bad cord include:

• Exposed or severed copper wiring visible inside
• External cracks, splits or abrasions eroding the casing  
• Erratic behavior during the wash cycle
• GFCI/EGCI outlet tripping frequently

Compatible models also include Electrolux, KitchenAid, Jenn-Air, and Kenmore options. Maintaining safety is a top priority.

This wire harness connects the appliance's control and power components to restore proper electrical routing and signal transfer. Replace a damaged harness to fix intermittent power, unresponsive controls, or burned/melted wiring concerns. What it does:

• Routes power and control signals between the control board, motors, switches, and sensors
• Replaces frayed, burned, or broken wiring that can cause intermittent operation or no power
• Prevents poor connections that lead to error codes, failed cycles, or component failures
• Restores factory wiring layout for reliable operation and safer electrical paths

• Disconnect power (unplug or switch off breaker) before starting any repair
• Match connector shapes and pin counts; do not force connectors into place
• Route harness along original clips and channels to avoid chafing or heat exposure

This ground wire provides a safe chassis connection to restore proper grounding and reduce shock and electrical-fault risk. It replaces a frayed, corroded or missing ground lead to help keep the appliance electrically safe. What it does

• Connects the appliance chassis to the grounding system to prevent stray voltage on metal surfaces
• Restores a secure ground path if the original wire is broken, loose, or corroded
• Helps stop intermittent power faults or nuisance tripping caused by a compromised ground
• Addresses symptoms like visible wire damage, loose ground connection points, or grounding-related electrical issues

• One ground wire

• Always disconnect power (unplug or shut off the circuit breaker) before starting work
• Attach the ring/terminal ends to the designated chassis ground screw and the equipment ground point
• Route the wire away from moving parts, heating elements, and sharp edges; secure with existing clips or fasteners
• If terminal hardware is missing or damaged, replace with equivalent OEM-style fasteners and torque to specification

This harness jump is a short jumper wire assembly used to reconnect two electrical terminals, restoring an intended circuit path for proper operation. It offers a direct, serviceable way to replace a broken or missing factory jumper. What it does:

• Bridges two terminals to complete a circuit when the original jumper is damaged or removed
• Helps restore power or signal to control components that rely on the jumper connection
• Commonly used in control, terminal block, or switch assemblies where a short wire link is required
• Can resolve symptoms such as intermittent or no power to a circuit, or a component not receiving a control signal

• One harness jump (single jumper wire assembly)

• High-level replacement only; ensure power is disconnected at the breaker or unplug the appliance before servicing
• Match connector style and terminal orientation to the original jumper before installing
• Inspect surrounding wiring and terminals for damage or corrosion; replace if needed

The Power Cord is an OEM part for Whirlpool dishwashers. This kit provides you with all the necessary parts to safely and effectively connect your dishwasher to the power source. The kit includes one power cord with a right angle head, one grommet, and one metal strain relief. The power cord with a right angle head allows for easy installation and helps to prevent excessive bending or damage to the cord.  

A bad power cord can occur due to wear and tear, exposure to heat or moisture, or accidental damage. If you notice symptoms such as intermittent power supply, sparks or electrical arcing, or a loose connection, it may be time to replace the power cord kit.

Symptoms of a bad power cord include:

• Intermittent power supply
• Sparks or electrical arcing
• Loose connection

Restore your Whirlpool dishwasher by replacing the faulty or damaged power cord kit with this genuine OEM part.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.