Parts for Kenmore 417.99576810 (41799576810, 417 99576810): Drum Parts

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

Top panel for laundry center units. Covers and protects the upper surface. Replace if cracked, chipped, discolored, or damaged from wear and tear.

This is a small metal grounding ball that sits in the rear drum bearing area of the dryer. It helps dissipate static electricity buildup in the drum during operation. Replace this part if you are experiencing excessive static cling on clothes, static shocks when unloading laundry, or if the original ball is missing or worn.

For a complete drum bearing and shaft kit order 5303281153.

Supports the dryer drum for smooth rotation. Replace if your dryer squeals, makes grinding noises, or the drum sags. Verify fit with your model number.

This metal bracket supports the drum bearing at the rear of the dryer, helping to hold the drum in proper alignment as it rotates. It provides a stable mounting point for the bearing assembly that the drum rides on. Replace this bracket if the dryer makes squealing, grinding, or thumping noises during operation, or if the drum wobbles and does not spin smoothly.

Replacement bracket screw for securing internal panels and brackets to your appliance frame. Needed when original screws are stripped, corroded, or missing.

The rear drum and heat duct housing is the back wall assembly of your dryer that supports the drum and channels heated air into the drum during drying cycles. It seals the rear of the drum and directs airflow efficiently across your clothes. Replace this part if the dryer is not heating evenly, the drum wobbles or scrapes against the back, or the housing is cracked and causing heat to escape.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

The Front Felt Glide Assembly is an OEM part for Frigidaire dryers. This part allows smooth operation of the dryer drum, providing a felt pad that the drum glides on as it rotates. This not only helps to support the drum but also minimizes friction and noise, contributing to the efficient and quiet operation of the dryer. 

Over time, the felt portion of the glide assembly can wear down, leading to increased friction between the drum and the dryer's front panel.  

Symptoms of a bad Front Felt Glide Assembly include:

• Unusual noises during operation, such as squeaking or grinding
• The dryer drum may catch or hesitate during rotation
• Increased wear and tear on clothing due to the drum's rough movement
• The dryer may take longer to dry clothes efficiently due to the drum's impaired rotation

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Front drum bulkhead for dryers. Mounts inside cabinet to support rotating drum. Replace if cracked, worn, or damaged to restore proper drum rotation.

The Lower Front Felt Seal is an OEM part for Frigidaire dryers. This seal prevents hot air from escaping the dryer drum, ensuring optimal drying efficiency and preventing heat loss. It also helps reduce noise and vibration during operation.

Causes of a faulty lower front felt seal can include wear and tear over time, damage from foreign objects or excessive heat, or adhesive failure. These factors can result in air leakage, increased drying time, or excessive lint buildup.

Symptoms of a front felt seal may include:

• Air leakage around the dryer door or front panel
• Excessive lint accumulation near the dryer opening
• Unusual noises or vibrations during the operation

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Note: For the Hi-Temp Adhesive, order part number 5308027429. Additional parts to check are the rear drum bearing kit 5303281153 and the front felt glide assembly 5303937139.

Mounting screw secures panels, trim, or brackets in dryers, washers, and ranges. Replace lost, stripped, or corroded screws to restore stability.

Dryer won't start or stops mid-cycle? A broken door catch prevents secure closure, triggering safety shutoffs. Simple snap-in replacement, 1 minute.

Traps lint and debris during drying to prevent vent clogs and maintain efficiency. Replace when torn, rusted, or bent. Verify fit with your model.

Replacement screw that secures panels and components in dryers, washers, and ranges. Needed when original fasteners are missing, stripped, or worn.

Interior drum baffle that lifts and tumbles clothes during the drying cycle. Replace if cracked, broken, melted, or missing to restore proper tumbling.

Phillips pan head screw for securing panels and components in appliances. Replace missing, stripped, or corroded screws during repairs or maintenance.

Supports the rear of your dryer drum for smooth, even rotation. Replace if drum wobbles, makes noise, or doesn't turn properly. Verify fit by model number.

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

This gasket is a sealing component used in select appliances. It fits between two mating parts to keep water or air where it belongs, helping prevent leaks and ensuring proper performance. What it does:

• Forms a tight seal between components or housings
• Helps prevent water drips, seepage, or air leaks at the joint
• Maintains correct appliance performance by keeping moisture/airflow contained
• Replace if the gasket is cracked, torn, flattened, or misshapen
• Common signs include residue, moisture, or visible gaps around the seal

• 1 gasket

• Disconnect power; turn off the water supply before servicing
• Note the orientation of the old gasket prior to removal
• Clean and dry the mating surfaces; remove any old gasket residue
• Seat the new gasket evenly without stretching; reassemble and check for leaks or proper seal

Dryer door won't stay closed? The door strike secures the door latch during operation. Quick DIY fix—installs from the front in minutes.

This is a heat shield insulator that mounts on the inner side of the dryer door in a stacked laundry center or washer/dryer combo unit. It prevents excessive heat from transferring through the door during drying cycles, protecting the outer door surface and improving energy efficiency. Replace this insulation if it is torn, deteriorated, or missing, which can cause the door to become excessively hot to the touch or reduce drying performance.

This is the manufacturer's installation instruction sheet for proper setup and initial use. It provides installer-facing steps and safety notes to help ensure the appliance is installed correctly and operates as intended. What it does:

• Gives step-by-step installation guidance and mounting/clearance requirements
• Lists basic safety warnings and required installation precautions
• Helps prevent installation errors that can cause performance issues or damage
• Advises on initial hookups (electrical, water, venting) in plain language

• Installation instruction sheet

• Read all instructions completely before starting installation
• Follow local codes and use qualified personnel for electrical/plumbing connections
• Keep this sheet with the appliance for future reference and for the owner
• If installation instructions conflict with local codes or the service manual, follow the code or service manual

Secures the backsheet to the cabinet, preventing panel gaps and rattling. Replace if clip is broken or panels are loose. Confirm fit with your model number.

This component adjusts the tension of washer suspension springs in laundry center units and is located within the suspension system. Replace when experiencing excessive vibration, unbalanced loads, or unusual movement during spin cycles.

Secures and organizes wires inside your appliance. Replace if broken, loose, or missing to prevent wire damage. Verify fit with your model number.

Harness cable tie secures and organizes wiring inside your appliance. Replace if damaged, cracked, or no longer holding wires firmly in place.

Snap-in bushing for washer assemblies. Replaces worn, cracked, or missing bushings that provide cushioning and support in internal components.

Converts compatible gas dryers from natural gas to propane. Includes orifices and components for safe LP operation. Order if switching fuel types.