Dryer Motor

This part is a genuine OEM replacement drive motor intended for use with dryer models. The drive motor works by rotating the drive belt, which in turn spins the dryer drum. A faulty motor could cause the drum to stop spinning altogether, or the user may notice a loud sound coming from the dryer when the drum tries to rotate. Work gloves should be worn, and the dryer should be unplugged from the power outlet before proceeding.This part was made by Frigidaire and has been sourced directly from the manufacturer. It is made out of high-quality, durable, non-corrosive materials to ensure the best possible durability. This drive motor is sold individually. It is intended for use with dryer models manufactured by Frigidaire, Electrolux, Gibson, Westinghouse, and other brands.

This drive motor powers the rotating component in your appliance, restoring smooth, reliable motion when the original motor is worn, seized, or noisy. Use it to fix no-rotation issues and inconsistent operation.

• Converts electrical energy into torque to rotate the attached component as designed for your model
• Helps resolve symptoms like no movement, stalling, or slow/intermittent rotation
• Restores consistent, dependable rotation under normal load

• Disconnect power at the breaker before servicing; appliances may contain sharp edges and high-voltage components—use caution
• Note wire/connector orientation and transfer any mounting grommets or brackets from the old motor
• Ensure the driven component turns freely by hand before restoring power
• After installation, run a short functional test to confirm proper rotation

This motor and pulley kit drives the drum belt and turns the blower wheel in your dryer. Replace a failing motor to bring back smooth tumbling and dependable airflow when the original hums, stalls, or overheats.

• Powers the drum via the belt and spins the blower to move air through the dryer
• Can be associated with overheating or burning smells when the motor is seized or shorted
• Addresses loud buzzing, grinding, or rattling noises from the motor area

• Disconnect power; if gas, shut off the gas supply before servicing
• Remove front/top panels for access; note belt routing and take photos of wiring
• Release belt tension, remove the drum, and detach the blower housing/wheel as required to free the motor
• Install the supplied pulley and move wires over one connector at a time; confirm free drum rotation before restoring power

The DC pump motor assembly powers the pump that moves water through your appliance. Replacing a worn motor helps restore proper water flow so cycles can complete and reduces issues like standing water and excessive noise.

• Drives the pump impeller to move water for draining or circulation, as designed by the appliance
• Supports proper cycle completion by clearing water from the tub or sump
• Common symptoms of a failing motor include standing water, incomplete draining/circulation, loud humming or grinding near the pump, or cycle errors
• May run intermittently, stall, or overheat as internal components wear

• Disconnect power and turn off the water supply before servicing
• Expect residual water; protect the area with towels or a shallow pan
• Note wiring connectors and hose routing; transfer any brackets, grommets, or seals from the original as needed
• Secure hose clamps and test for leaks while running a brief test cycle

This drive motor has been manufactured by Whirlpool and is intended to replace a worn or faulty part in dryers.The drive motor enables the dryer to work as intended because it rotates the drive belt, which in turn spins the drum. Without a working motor, the drum won't rotate efficiently or at all and the materials and clothes will not be dried properly. Thus, a broken drive motor should be immediately replaced. To ensure safety when working on this appliance, make sure it has been entirely disconnected from the power source and work gloves are worn to prevent injuries from occurring.This is a genuine OEM part sourced from the manufacturer and is compatible with various dryers that have been made by Whirlpool, Maytag, Amana, and other brands. This part has been manufactured from high-quality, durable, non-corrosive materials to ensure the best possible quality and is only sold individually.

This split-phase motor assembly powers a dryer's drum and blower on qualifying 29" export 50Hz models, restoring rotation and airflow for normal drying performance. Designed as a direct-replacement motor assembly. What it does:

• Drives the dryer drum and blower fan to circulate air through the drum.
• Helps re-establish regular tumbling and airflow when the motor has failed.
• Commonly replaces motors that hum, do not start, or stop suddenly during cycles.

• Disconnect power before attempting service to avoid shock or injury.
• Handle the motor and wiring harness carefully to avoid pinched wires or damaged terminals.

The Motor Assembly is an OEM component specifically designed for GE laundry machines. This assembly contains the motor and blower wheel that are responsible for forcing air through the dryer and circulating hot air around clothes during the drying cycle. 

Causes of a bad motor assembly can include wear and tear over time, exposure to high heat cycles that can depreciate motor insulation or bearings, or damage due to impact or mishandling. 

Symptoms of a bad motor assembly include:

• The dryer not heating or only heating intermittently  
• Loud grinding or knocking noises originating from the motor area
• The blower wheel no longer spins or turns slowly
• Extended drying times 

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Drive Motor is an OEM component for Whirlpool electric and gas dryers. It powers the rotating drum and tumbling of clothes during drying cycles.

The drive motor may fail due to wear and tear over time, electrical issues, or damage to the motor's internal components. Regular use, exposure to lint and dust, and overheating can contribute to motor failure.

Symptoms of a bad drive motor include:

• The dryer drum not spinning
• Unusual noises such as humming or buzzing
• The dryer not starting
• The motor overheating or shutting off

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Drum Motor Assembly is an OEM part for LG dryers. It serves as the powerhouse that drives the drum, enabling it to tumble clothes during the drying cycle. This essential component ensures your dryer operates smoothly, providing the necessary torque for consistent and efficient drying performance.

Causes of failure might include wear and tear from prolonged use, overload from trying to dry heavy loads, electrical issues like short circuits, or physical damage to the motor components. 

Symptoms of a bad Drum Motor Assembly include:

• The dryer drum fails to turn, even though the dryer powers on.
• Unusual noises, such as humming or buzzing, indicating the motor is struggling.
• The dryer stops unexpectedly during cycles or won't start at all.
• Decreased drying efficiency or clothes taking longer to dry due to inconsistent drum speed.

This OEM LG part is also compatible with Sears/Kenmore.

This drive motor powers the appliance's main drive system, converting electrical energy into steady rotation under load. Replacing a weak, noisy, or seized motor restores proper movement and dependable operation. What it does

• Provides the mechanical torque that turns the appliance's drive system
• Resolves symptoms like no movement, humming/buzzing without turning, or stalling under load
• Helps eliminate intermittent starting and overheating shutdowns
• Reduces grinding/squealing motor noises caused by worn bearings or a failing armature

• One drive motor assembly

• Disconnect power before servicing; also shut off gas supply
• Take photos/label wires, then transfer connectors and any mounting parts from the old motor
• Ensure the motor spins freely and the belt/pulley alignment is correct before reassembly
• After installation, perform a brief test run while observing for smooth, quiet operation

This axial motor assembly drives a cooling fan to move air through the appliance, helping protect internal components from heat. Replacing a worn or noisy unit restores ventilation and reduces heat-related shutdowns or performance issues.

• Circulates air across heat-generating parts to dissipate heat
• Helps maintain stable operating temperature and protect electronics
• Failure signs can include the fan not running, intermittent operation, loud or grinding noise, overheating, or a burning smell
• Inadequate airflow may trigger thermal cutoffs or nuisance shutdowns

• Disconnect power before servicing; allow hot components to cool
• Access the motor location and note wire positions; take photos for reference
• Transfer any brackets or grommets from the old unit if required; keep wiring clear of the fan path
• After mounting, hand-spin the fan to ensure free movement before restoring power and checking airflow