Electrolux Dryer Parts

The Door Hinge is an OEM part for Frigidaire dryers. This hinge allows it to open and close properly while maintaining a secure seal during the drying cycle.

Causes of a bad door hinge can include wear and tear from regular use, rust or corrosion due to exposure to moisture, or damage from accidental impacts. 

Symptoms of a bad door hinge include:

• Difficulty opening or closing the dryer door
• The door not sealing properly, leading to heat loss
• Squeaking or creaking noises when moving the door
• Visible damage or rust on the hinge

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This door handle provides the grip to open and close the appliance door. Replace a cracked, loose, or missing handle to restore easy access and a clean, finished look.

• Provides the user handhold to operate the door
• Mounts to the door panel and transfers pull force to the latch mechanism
• Common symptoms: handle cracked/broken, loose or falling off, difficulty opening the door
• Helps address cosmetic damage or sharp edges from a broken handle

• Disconnect power to the appliance before servicing
• Open the door and support the outer panel or glass, if applicable
• Transfer and reuse original fasteners; align the new handle and tighten evenly—do not overtighten
• Verify smooth door operation before returning to service

This door switch senses whether the appliance door is closed and signals the controls to run only when it's safe. Replacing a worn or intermittent switch restores dependable starts and proper shutoff when the door opens. What it does:

• Detects door position and allows operation only when the door is fully closed
• Interrupts operation when the door opens for safety
• Common symptoms include: won't start, stops when the door is moved, or "door open" message/error
• Intermittent starts due to worn actuator or internal switch contacts

• 1 door switch

• Disconnect power before servicing
• Access the switch from the front or top panel; release mounting screws or tabs
• Move wires to the new switch one at a time to maintain correct positions, then secure the switch
• Test operation before reassembly

The Lid Lock Switch is an OEM part for Frigidaire washing machines. This switch is responsible for ensuring the lid is securely locked during the wash and spin cycles, preventing the lid from being opened and ensuring safe operation of the machine.

Causes of a bad lid lock switch can include electrical failures, wear and tear from frequent use, or damage due to impact or mishandling.  

Symptoms of a bad lid lock switch include:

• The washing machine not starting or stopping mid-cycle
• The lid not locking or unlocking as expected
• Error codes related to the lid lock mechanism
• Unusual noises during the wash or spin cycles

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Adjustable Foot is an OEM part for Frigidaire dryers. This part is located at the bottom of the dryer and allows you to level it, ensuring stability and proper operation. 

Causes of a bad adjustable foot can include regular wear and tear, damage from moving the appliance, or breaking due to excessive weight or stress.  

Symptoms of a bad adjustable foot include:

• The dryer wobbling or tilting
• Difficulty in adjusting the height of the foot
• Visible damage or deformation of the foot
• Unusual noises or vibrations during operation

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This LP conversion kit contains the calibrated components needed to convert compatible natural gas appliances to operate on liquid propane, helping ensure proper fuel flow and flame performance when switching gas sources.

• Provides propane-rated orifices and components to adjust gas flow from natural gas to LP
• Helps correct issues like yellow, lazy, or oversized flames after a fuel change
• Supports safe, efficient burner ignition and heating on LP
• Used when local fuel supply is propane instead of natural gas

• For safety, shut off gas and electrical power before beginning; allow the appliance to cool
• Conversion must follow the appliance's service manual and LP instructions
• Adjust regulator setting and burner/orifice sizing per included and model-specific guidance
• Leak-test all gas connections with an approved method before restoring service

This idler spring attaches to the idler arm to keep the drive belt properly tensioned, preventing slip and chatter. Replacing a weak or broken spring restores steady rotation and helps reduce noise and belt wear.

• Maintains correct belt tension by pulling the idler arm into position
• Helps prevent belt slippage, squealing/chirping, and premature belt wear
• A failed spring can cause no or intermittent rotation and the belt coming off
• Typical signs include a loose belt, off-track belt, or rhythmic squeak from the base

• Disconnect power before servicing; if working on a gas appliance, shut off the gas supply
• Access the idler assembly; note belt routing before removal
• Relieve belt tension, then move the idler arm to remove and replace the spring on the same mounting holes
• After reassembly, rotate by hand to verify smooth belt tracking before test

This replacement gasket restores a tight, reliable seal between mating parts in your appliance. It helps contain water or air at the joint to prevent leaks, odors, and performance issues.

• Creates a compressible barrier that prevents leaks at the sealed interface
• Helps maintain proper containment/airflow, depending on application
• Replace if torn, cracked, shrunken, or permanently flattened
• Typical symptoms include moisture or drips at the seam, musty odors, or visible damage

• Disconnect power; shut off water supply if applicable before servicing
• Use your model's parts diagram to locate and orient
• Clean and dry mating surfaces; remove any old adhesive or residue so the new seal seats properly
• Reassemble evenly, avoid over-tightening fasteners, and test for leaks after reassembly

The Leveling Leg is an OEM part for Frigidaire washers. It is designed to provide stability and level the appliance properly on the floor during installation and operation.

Common causes for needing to replace the leveling leg include damage or wear over time, which can lead to unevenness and excessive vibration during wash cycles.

Symptoms that may indicate the need for a replacement leveling leg:

• Uneven or unstable washing machine
• Excessive shaking or vibration during spin cycles
• Difficulty in leveling the washer during installation

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Door Switch is an OEM part for Frigidaire clothes dryers. It is an electronic component located on the door frame that detects when the dryer door is latched closed. The switch communicates this information to the control board, allowing the dryer to operate properly by preventing operation if the door is open.

Causes of a bad door switch can include normal wear and tear from opening and closing the dryer door over time. Physical damage from accidental impacts or overtightening of door mounting hardware may also cause switch failure.

Symptoms of a bad dryer door switch include:

• The dryer starting a cycle even when the door is open
• Error codes or failure to start/run if the door switch does not detect proper closure
• Other control issues related to incorrectly sensing door position

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This line noise filter conditions incoming AC power by reducing electromagnetic interference before it reaches the appliance's electronics. Replacing a shorted or damaged filter can restore stable operation and help prevent erratic control behavior.

• Filters EMI/RFI on the power line before it reaches the control system
• Helps protect sensitive electronics from interference and voltage spikes
• Failure may present as no power, intermittent resets, or nuisance GFCI/breaker trips
• Typically mounted near the power-cord entry; also called a line filter

• Disconnect power and allow any capacitors to discharge before servicing
• Note wire positions and line vs. load orientation; take a photo before removal
• Secure the ground and mount the new filter firmly to the chassis
• Route and reconnect wires carefully to avoid pinching; reassemble and test

This gasket is a sealing component used in select appliances. It fits between two mating parts to keep water or air where it belongs, helping prevent leaks and ensuring proper performance. What it does:

• Forms a tight seal between components or housings
• Helps prevent water drips, seepage, or air leaks at the joint
• Maintains correct appliance performance by keeping moisture/airflow contained
• Replace if the gasket is cracked, torn, flattened, or misshapen
• Common signs include residue, moisture, or visible gaps around the seal

• 1 gasket

• Disconnect power; turn off the water supply before servicing
• Note the orientation of the old gasket prior to removal
• Clean and dry the mating surfaces; remove any old gasket residue
• Seat the new gasket evenly without stretching; reassemble and check for leaks or proper seal

The Terminal Block is an OEM replacement part for Frigidaire clothes dryers. It is the part the power cord connects to. This kit includes 3 screws and 3 terminals.

Causes of a bad terminal block can include damage from age, overheating from worn wires or loose connections, or improper installation during manufacturing.

Symptoms of a bad terminal block include:

• The dryer not powering on
• Intermittent heating issues
• Loose, frayed, or damaged wires

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

This thermistor is the temperature-sensing component that feeds accurate readings to the appliance's control. Replacing a faulty sensor restores proper temperature feedback, helping the control run cycles correctly and reduce temperature-related performance issues. What it does:

• Monitors temperature and changes resistance with temperature (NTC), sending a signal to the control board
• Helps the control regulate heating or water-temperature management during operation
• When open/shorted or out of range, can trigger temperature/sensor error codes
• Symptoms include inconsistent temperatures, long run times, or cycles that won't complete

• 1 thermistor

• Disconnect power before servicing; shut off gas/water supply if applicable
• Access the sensor per your model; it's typically secured by a clip or screw and connects via a wire harness
• Note wire orientation; avoid pulling on wires and ensure the connector is fully seated
• After installation, clear any stored error codes and run a diagnostic or test cycle

This dryer blower moves air through the drum, lint filter, and exhaust so laundry dries efficiently. Replacing a damaged blower restores proper airflow and helps prevent long dry times and overheating issues.

• Draws and circulates air across the heater, through the drum and lint filter, and out the vent
• Maintains correct airflow and temperature control for consistent drying performance
• Worn, cracked, or clogged blowers may cause weak exhaust airflow and extended dry cycles
• May also present as rattling/grinding noises from the blower area or high-heat shutoffs

• Disconnect power; if gas, turn off gas supply before servicing
• Access the blower by removing the front/lower panel and blower cover
• Clean lint/debris from the housing and duct; transfer any seals or hardware from the original as needed
• After installation, spin the blower by hand to verify free movement; reassemble and test airflow

The Frigidaire Touch-Up Paint is white in color in a .6 fl oz bottle. For almond order 5303321320. For black order 5303321321.

The Touch Up Paint is an OEM part for Frigidaire appliances. Whether you're dealing with scratches, chips, or other minor cosmetic damage, this touch-up paint provides an easy and effective solution for maintaining the appearance of your appliance. It's designed to adhere well to metal surfaces, offering durability and resistance to further wear and tear.

Over time, appliances can accumulate minor surface damage from regular use, cleaning, and accidental impacts. Using the Touch Up Paint not only improves the aesthetic appeal of your appliance but also helps protect exposed areas from rust and corrosion, which can extend the life of the appliance.

Symptoms of needing Touch Up Paint include:

• Visible scratches or chips on the appliance's surface.
• Areas of rust or corrosion that need to be covered after treating the rust.
• The desire to maintain or improve the appliance's appearance for aesthetic reasons or to maintain its value.