Freezer Gasket & Seal

This refrigerator door gasket seals the door to the cabinet to keep cold air in and humid air out. Replacing a worn gasket restores a tight seal, helps maintain temperature, and reduces frost and energy loss.

• Forms an air-tight perimeter seal between the door and cabinet
• Helps maintain stable interior temperature and humidity
• Reduces frost, condensation, and air leaks
• Resolves: torn or deformed gasket, door not sealing or popping open, moisture around the door, excessive frost or longer run times

• Disconnect power before servicing
• Warm the new gasket to relax folds; use warm water or low heat to ease installation
• Remove the old gasket from the retainer; if screws are present, loosen to replace; seat corners first and press the bead fully into the channel
• After installation, check for uniform contact around the seal; close the door to help the gasket set and adjust door alignment if needed

The Evaporator Cover Gasket seals the perimeter of the freezer's evaporator cover to prevent air leaks that can lead to frost, moisture, and temperature swings. Replacing a worn gasket helps restore proper airflow and consistent cooling.

• Seals the evaporator cover to the liner to maintain directed airflow and contain cold air
• Helps prevent frost or ice buildup around the cover and on nearby air passages
• Can help address symptoms like temperature inconsistencies, poor cooling, or excess moisture caused by air leaks
• Replaces a torn, flattened, or missing gasket to ensure a tight cover fit

• Disconnect power before servicing; wear cut-resistant gloves
• Remove freezer shelves/bins and the evaporator cover to access the gasket
• Clean mating surfaces; press the new gasket fully into place with no gaps or twists
• Ensure air vents are unobstructed, reinstall the cover securely, then restore power

This refrigerator seal restores a tight barrier between internal components. Replacing a worn or damaged seal helps prevent air leaks and moisture intrusion, supporting proper airflow, stable temperatures, and reduced frost or condensation around the joint.

• Creates an air-tight barrier between mating surfaces
• Helps maintain correct airflow and temperature balance between compartments
• Reduces frost, condensation, and warm/cold spots near the sealed area
• Common signs of failure: visible gaps, loose/crumbled seal, rattling panel, moisture or frost at the joint

• Disconnect power before servicing
• Remove the related cover or housing to access the old seal
• Clean contact surfaces; install the new seal in the same orientation without stretching or pinching
• Reassemble and verify an even seal and normal airflow before returning to service

This replacement freezer door gasket restores a tight seal to help keep the freezer cold and reduce frost buildup. Designed to fit the freezer door, it gives an easy, low-cost way to improve cooling performance and efficiency. What it does:

• Seals the freezer door to prevent warm air and moisture from entering
• Helps reduce frost buildup and maintains consistent internal temperature
• Restores proper door closure when the existing gasket is cracked, flattened, or torn
• Supports energy efficiency by minimizing cold-air loss

• Inspect door frame and mounting channel; clean and dry before installing the new gasket
• Press gasket into the door channel evenly, starting at one corner and working around the perimeter
• For best seal, level and align the door after installation; allow gasket to seat for several hours
• Disconnect power only if needed for light removal tasks

This is a replacement refrigerator door gasket that seals the door to help maintain consistent internal temperature and improve energy efficiency. It restores a proper seal to reduce cold air loss and protect stored food. What it does:

• Creates an airtight seal around the refrigerator door to prevent warm air intrusion
• Helps maintain stable internal temperature and reduce frost buildup
• Reduces compressor run-time caused by a leaking door seal
• Commonly used when the existing gasket is cracked, torn, warped, or no longer seals

• Inspect the door, liner, and mounting channel for damage or debris before installing
• Clean mounting surfaces and warm or flex the gasket as needed for easier seating
• Apply even pressure around the perimeter; replace any damaged mounting clips or fasteners
• Disconnect power or follow appliance-specific safety steps when working near electrical components

This door gasket seals the perimeter of the refrigerator or freezer door to maintain an airtight closure. Replacing a worn gasket restores a proper seal, helps stabilize temperatures, reduces frost and condensation, and supports efficient operation. What it does:

• Creates a tight seal between the door and cabinet to keep cold air in and warm air out
• Helps reduce frost buildup and moisture around the door opening
• Can address temperature fluctuations, long run times, and doors that won't fully close
• Replace if torn, deformed, brittle, or no longer sealing evenly

• 1 door gasket

• Disconnect power before servicing; open the door and remove the old gasket from its retainer/channel
• Warm the new gasket (soak in warm water) to relax and straighten before installation
• Seat the corners first, then work evenly around the perimeter to fully engage the retainer
• Close the door and check for uniform contact; adjust the gasket/retainer as needed for a complete seal

The Door Gasket is an essential OEM component for Frigidaire top-freezer refrigerators. It establishes an insulating air seal around the perimeter of the refrigerator and freezer doors.

Causes of failure include breakdown of sealing materials from prolonged compression during repeated closure stresses. Damage like cracks or tears diminish gasket capabilities over time.

Symptoms of a faulty door gasket include: 

• Cool air leakage resulting in warmer interior temperatures
• Frost or condensation buildup visible around door frames
• Physical deterioration like tearing or perishing gasket materials

This OEM Frigidaire replacement gasket is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. 

This door gasket is a replacement refrigerator door seal that helps maintain an airtight closure to keep cold air in and reduce temperature fluctuations. Restores proper sealing to help the fridge run efficiently and protect food. What it does:

• Seals the refrigerator door to prevent warm air from entering and cold air from escaping
• Helps reduce frost buildup and uneven cooling caused by a failing seal
• Can lower strain on the compressor by improving temperature stability
• Addresses symptoms such as visible gaps, drafts, or moisture buildup around the door

• Disconnect power to the appliance before starting any work
• Clean and dry the door frame surface before installing the new gasket for a tight seal
• Remove the old gasket carefully; use hand tools and avoid sharp implements that could damage the cabinet
• Follow the appliance manufacturer's installation instructions for proper fit and tab alignment

This replacement door gasket creates a tight seal around the refrigerator door to help keep cold air in and maintain consistent temperatures. It restores proper sealing to reduce frost, cycling, and energy loss. What it does:

• Seals the refrigerator door edge to prevent warm air infiltration and cold air escape
• Helps reduce interior frost buildup and excessive compressor cycling
• Restores a consistent internal temperature for better food preservation
• Can improve cooling efficiency when the original gasket is torn, warped, or compressed

• Disconnect power to the appliance before beginning any repair
• Remove the old gasket and clean the door flange/mating surface before installing the new gasket
• Work the gasket into the channel evenly, ensuring the magnetic edge seats fully around the door
• If needed, warm the gasket slightly to aid flexibility; avoid excessive heat and sharp tools

This right-side evaporator cover gasket seals the evaporator cover to help prevent air leaks and reduce frost buildup, supporting consistent cooling and efficient refrigerator operation. What it does:

• Seals the evaporator cover to minimize warm air intrusion and reduce ice accumulation on the evaporator
• Helps maintain stable compartment temperatures for better cooling performance
• Reduces moisture and dripping that can cause water pooling inside the cabinet
• Can address symptoms such as increased frost on the evaporator, higher-than-normal temperatures, or water inside the fresh food/freezer area

• Disconnect power to the appliance before beginning any repair
• Remove necessary interior panels or shelves to access the evaporator cover per the service manual
• Seat the gasket fully around the cover flange; inspect the cover and seating surface for damage or debris