Freezer Parts

Outer drawer slide rail for refrigerator pantry drawers. Guides drawer movement for smooth opening and closing. Replace if cracked, bent, or worn out.

Replaces cracked or broken mounting bracket in your freezer. Securely holds internal components in proper alignment. Needed when original is damaged.

This replacement heater restores proper heat output to the feature that uses it, helping your appliance reach and maintain temperature for consistent results. When the original heater fails open or shorts, related cycles may not heat or take much longer.

• Converts electrical energy into heat within the appliance's heating circuit
• Maintains target temperature during the selected function
• Common symptoms: no heat in the related feature, extended preheat/warm-up, uneven results, or heating-circuit error codes
• Visible signs can include breaks, burn spots, or an open element on continuity testing

• Disconnect power at the breaker or unplug before servicing; allow components to cool
• Note wire positions and fasteners for accurate reassembly; transfer any reusable clips/insulators
• Handle the element carefully—avoid bending or striking; make clean, tight electrical connections
• After installation, run a brief test cycle to ensure proper heating

This door rack mounts to the inside of the refrigerator or freezer door to hold small items securely. Replace a cracked or missing rack to restore door storage and prevent items from falling when the door opens and closes.

• Provides additional storage on the inner door for jars, condiments, and small items
• Helps keep contents organized and stable during door movement
• Common symptoms: broken or missing rack, items falling from the door, reduced storage space
• Restores original fit and function when the existing rack is damaged

• Unplug the appliance before servicing
• Remove items from the affected door area
• Lift or release the old rack from the end supports/slots; seat the new rack fully into the same supports
• Confirm the rack is secure before reloading and avoid overloading to prevent damage

This Temperature Controller regulates cooling by switching power to the compressor and related circuits to hold the set temperature. Replacing a failing controller restores accurate temperature control and reliable operation. What it does:

• Cycles cooling components to maintain the temperature you set
• Helps keep cabinet temperatures consistent for proper food storage
• Coordinates on/off operation to prevent overcooling or warm conditions
• Common failure symptoms: too warm or too cold, runs constantly or won't start, control/dial unresponsive

• 1 temperature controller

• Disconnect power before servicing—this is a line-voltage control
• Access the control area, label or photograph wire positions, and move wires one at a time to the new controller
• Reuse existing mounting hardware and any knob/overlay as applicable
• After install, set to mid setting and allow up to 24 hours for temperatures to stabilize

This electronic controller is the central board that governs your unit's cooling system. It processes temperature inputs and controls key components so the freezer maintains set temperature when the original board fails.

• Regulates temperature by processing sensor/thermostat inputs and issuing commands to cooling components
• Directs compressor and fan operation to maintain the setpoint
• On applicable models, manages defrost timing and cycles
• Common failure symptoms include no cooling or intermittent cooling, unit won't start, runs constantly, unresponsive controls, or erratic temperatures

• Disconnect power before service; observe ESD precautions and handle the board by its edges
• Photograph/label wire connections; transfer any mounting clips/brackets from the original board
• Seat all connectors fully without forcing; avoid touching component pins
• Restore power and allow time for temperatures to stabilize; verify normal operation

Replacement hinge assembly for chest freezer lids. Provides pivot support for smooth opening and secure closing. Replace if cracked, broken, or worn.

Refrigerator won't cool or compressor clicks but won't start? This PTC start relay powers the compressor's start winding. Common DIY fix, restores cooling.

Replacement slide rail that mounts inside the freezer to support and guide storage baskets. Replace if cracked, broken, or worn to restore smooth gliding.

This electronic control is the oven's main user interface and control board, restoring reliable cycle selection and display feedback so your range or wall oven responds correctly and settings hold as expected. What it does:

• Interprets button/touchpad inputs and sends commands to heating elements, timers and relays.
• Restores or corrects digital display, clock and oven mode functions.
• Can resolve symptoms such as blank or erratic display, unresponsive controls, incorrect bake/clean cycles, or oven failing to start.
• Works as the central board that coordinates temperature and timing signals for normal oven operation.

• Always disconnect power at the breaker or unplug the appliance before inspecting or replacing controls.
• Handle the board carefully to avoid static discharge; avoid touching circuit traces or components.
• Follow the appliance's service manual or diagram for correct wire connections and panel reassembly.

This thermostat is a temperature-sensitive switch that controls power to cooling components as temperatures change. Replacing a worn thermostat restores consistent cycling and more accurate temperature regulation, helping the appliance maintain stable performance. What it does:

• Senses temperature and opens/closes electrical contacts at set points
• Regulates operation of key cooling components to maintain target temperature
• Helps prevent overcooling, overheating, and erratic cycling
• Failure signs include: no cooling, overcooling, temperature swings, unit runs continuously, or short-cycling

• 1 thermostat

• Disconnect power before servicing; verify no voltage is present
• Access the thermostat location; label/photograph wire positions and transfer one at a time
• Install in the same position and orientation as the original to ensure proper thermal response
• Restore power and confirm proper cycling and temperature control

Fridge not cooling or making loud buzzing noise? This compressor kit restores cooling in refrigerators and freezers. Professional repair recommended.

Freezer won't shut off or stop cooling? This temperature control thermostat cycles the compressor on and off to maintain set temps. DIY repair.

This light socket holds the interior appliance bulb and connects it to the unit's wiring. Replace a damaged or loose socket to restore dependable cabinet lighting when the door is opened.

• Secures the interior light bulb and provides reliable electrical contact
• Supplies power to the lamp when the door switch closes
• Helps resolve flickering or intermittent lighting from a worn or heat-damaged socket
• Common symptoms: light won't turn on, bulb won't seat or stays loose, visible charring at the socket

• Disconnect power to the appliance before servicing
• Remove the lens/cover and bulb; release the socket from its mounting
• Transfer wires one at a time to the new socket and ensure snug connections
• Reinstall bulb and cover, restore power, and test; use the bulb type/wattage specified by the manufacturer

This electronic control board is the freezer's central control module. It processes sensor inputs and user settings to run the cooling system and alerts. Replacing a failed board helps restore reliable operation and accurate temperature management. What it does:

• Controls compressor and evaporator fan operation to maintain the set temperature
• Interprets thermistor input and applies control logic to regulate cooling
• Coordinates features such as alarms and, on electronic models, defrost cycles
• Common symptoms include the unit not running or powering up, warming or unstable temperatures, unresponsive or erratic controls/display, or excessive frost buildup

• Disconnect power before servicing; handle the board with ESD precautions
• Access the control housing, note wire locations, and transfer connectors one at a time
• Secure the replacement board and reuse original mounting hardware and any reusable trim/overlay as applicable
• Restore power, set temperatures, and allow up to 24 hours for stabilization

Electronic touch pad control board that mounts on the freezer door. Replace if cracked, unresponsive, or damaged by power surge. Plug-in installation.