Freezer Parts

This is the electronic control board that governs the appliance's cooling system. It interprets sensor input and user settings to run key components, helping maintain consistent temperatures when the original controller becomes faulty or erratic.

• Monitors temperature sensor feedback and executes cooling cycles to hold the selected setpoint
• Controls major components on applicable models
• May manage additional functions like defrost timing or alarms depending on model design
• Failure can present as warm or unstable temperatures, unit not starting, short-cycling/running constantly, or unresponsive temperature adjustments

• Disconnect power before service; observe ESD precautions and handle the board by its edges
• Note wire/plug locations; transfer connectors to the new board one at a time
• Secure the board in its mounting and ensure all harnesses are fully seated
• Reassemble covers/panels before restoring power and checking operation

This defrost heater assembly mounts near the evaporator coils inside the freezer compartment and generates heat to melt frost buildup during the automatic defrost cycle. It keeps the evaporator coils clear so the refrigerator can cool efficiently. Replace this heater if you notice excessive frost buildup in the freezer, the refrigerator is not cooling properly, or the defrost cycle is not functioning.

Replacement screw that secures brackets, shelves, trim, panels, and covers inside your appliance. Install when the original is missing, stripped, or corroded.

Fixes ice buildup in freezer and warm fresh food compartment. This bimetal defrost thermostat controls heater cycles to prevent frost accumulation.

Outer drawer slide rail for refrigerator pantry drawers. Guides drawer movement for smooth opening and closing. Replace if cracked, bent, or worn out.

Color: White

Freezer not cooling or running constantly? This compressor kit circulates refrigerant through the system. Advanced repair requires refrigerant handling.

Electronic control board with integrated touch pad for freestanding freezers. Replaces failed boards with unresponsive buttons, cracked touch panels, or damaged controls.

This electronic controller is the central board that governs your unit's cooling system. It processes temperature inputs and controls key components so the freezer maintains set temperature when the original board fails.

• Regulates temperature by processing sensor/thermostat inputs and issuing commands to cooling components
• Directs compressor and fan operation to maintain the setpoint
• On applicable models, manages defrost timing and cycles
• Common failure symptoms include no cooling or intermittent cooling, unit won't start, runs constantly, unresponsive controls, or erratic temperatures

• Disconnect power before service; observe ESD precautions and handle the board by its edges
• Photograph/label wire connections; transfer any mounting clips/brackets from the original board
• Seat all connectors fully without forcing; avoid touching component pins
• Restore power and allow time for temperatures to stabilize; verify normal operation

Freezer won't cool or runs constantly? This temperature control thermostat regulates cooling cycles to maintain proper temperature. Moderate DIY repair.

Refrigerator won't cool or compressor clicks but won't start? This PTC start relay powers the compressor's start winding. Common DIY fix, restores cooling.

This mechanical temperature control thermostat regulates your unit's cooling by cycling the compressor on and off to maintain the set temperature. Replace a failed cold control when temperatures drift, cycling is erratic, or the knob no longer responds.

• Monitors cabinet temperature via a sensing bulb and opens/closes electrical contacts to control cooling
• Helps restore consistent temperatures and normal run times
• Typical failure symptoms: too warm or too cold, runs constantly or won't start, no change when adjusting the control
• May cause intermittent cooling or short cycling as it wears

• Disconnect power before servicing
• Access the control housing; note/photograph wire locations and transfer them one at a time
• Route the sensing capillary exactly as original; do not kink or sharply bend the tube; secure the bulb in its original location
• Set the control to a mid setting and allow temperatures to stabilize before fine-tuning

Small mounting bracket that holds shelves or baskets inside your freezer. Replace if cracked, broken, or missing to restore secure, level positioning.

Replacement door handle for refrigerators and freezers. Installs on the front of the door to provide a secure grip. Replace when cracked, loose, or broken.

Touch-up paint for appliances. Covers chips, scratches, and worn areas on range tops, refrigerators, and other appliances. Includes brush applicator.