Frigidaire Range Switch

This surface element switch is the control behind your cooktop knob. It regulates power to the surface heating element so you can set and maintain the desired heat for reliable, consistent cooking performance.

• Regulates and cycles power to the surface heating element based on the knob setting
• Restores accurate low-to-high temperature control at the burner
• Typical failure symptoms: burner won't heat, only heats on high, or won't turn off
• Helps correct intermittent or uneven surface element heating

• Disconnect power at the circuit breaker before servicing
• Remove the knob and access the switch from the control panel or rear cover as applicable
• Photograph or label wire positions; transfer wires to the new switch one at a time
• Secure the switch, reassemble, restore power, and test all heat settings

This electrical microswitch opens or closes a circuit when its actuator is engaged, allowing the control to sense position or enable a function. Replacing a worn switch restores reliable signaling and prevents intermittent faults in select ranges and wall ovens. What it does

• Changes state (open/closed) when actuated to complete or break a circuit
• Sends feedback to the control or enables power to a related component
• Helps ensure operations start/stop only when the mechanism is in the correct position
• Failure signs can include intermittent operation, cycles that won't start or finish, or related error codes/alarms

• 1 switch

• Disconnect power at the breaker before servicing
• Note/photograph wire positions and transfer one at a time to the new switch
• Match actuator orientation to the original and secure the switch firmly
• Verify function with a multimeter (continuity changes when actuated) before reassembly and testing

This rocker switch is the on/off control used in the appliance's control panel. It opens and closes the circuit to a selected feature, restoring dependable operation when the original switch becomes worn, stuck, or fails.

• Controls a single on/off circuit from the control panel
• Restores proper switching for the associated feature
• Common symptoms: feature won't turn on or off, light or function flickers or stays on, switch feels loose or sticks
• Replaces a cracked, burned, or unresponsive rocker

• Disconnect power at the breaker before servicing
• Access the switch from the control panel or mounting area; note/photograph wire positions
• Move wires to the new switch one at a time and seat the switch securely in the panel opening
• Restore power and test operation before reassembly

This potentiometer kit is the user-adjustment control the appliance reads to set operating levels. Replacing a worn potentiometer restores smooth, predictable response when you turn the knob, helping the control register settings accurately.

• Varies electrical resistance so the control can interpret knob position
• Helps set functions such as speed, power level, or temperature as designed
• Failure can present as no change when turning the knob, jumpy/erratic response, or settings stuck at one level
• Can also cause intermittent operation or "dead spots" while adjusting

• Disconnect power to the appliance before servicing
• Access the control area; note wire positions or take a photo before removal
• Transfer any knob/shaft adapter from the old part if applicable; secure the new pot without over-tightening
• Route wiring away from sharp edges and heat sources; verify proper operation before reassembly

This switch assembly restores electrical on/off control for a specific appliance function. Replace a worn or failed switch to stop intermittent operation and return reliable control to the affected circuit. What it does:

• Provides the electrical on/off or function control for the appliance circuit.
• Replaces a failed switch that can cause intermittent operation or unresponsive controls.
• Helps resolve symptoms such as a function that won't start, no response from the control, or erratic switching.
• Connects to the existing wiring harness and mates with the original mounting points.

• Disconnect power to the appliance before beginning any work.
• Remove the appropriate access panel to reach the switch; note wire and terminal locations before disconnecting.
• Unplug the wiring harness or carefully detach terminals, swap the switch assembly, then reconnect securely.
• Restore power and verify the replaced switch operates the function correctly.

This is the variable control switch for an electric range's cooktop burner. It regulates power to the surface element so you can select steady, repeatable heat levels and restore reliable on/off control. What it does:

• Regulates voltage to a surface element based on knob position (low through high)
• Typical failure symptoms: burner won't heat, only heats on high, won't shut off, or heats inconsistently
• Can address issues when the control shaft is damaged or the switch shows signs of overheating at the terminals

• 1 switch

• Disconnect power before servicing
• Access the control panel/console to reach the switch
• Note wire locations and transfer them to the new switch one at a time
• Secure the switch in the panel, reinstall knob, and test burner operation before reassembly

This replacement switch restores reliable on/off control for a specific function in the appliance, helping the selected feature respond consistently when operated.

• Controls electrical power to a designated circuit or component when actuated
• Sends an on/off signal to the control or directly to the component it operates
• Failure symptoms can include no response, intermittent operation, or a switch that feels loose, sticks, or is hard to press
• May show signs of heat damage, arcing, or a burning smell near the control area when faulty

• Disconnect power at the breaker before servicing to avoid electrical shock
• Access location varies by model; remove the control panel, backguard, or front panel as needed
• Label or photograph wire positions and transfer them one at a time to the new switch
• After reassembly, restore power and test operation of the associated function

This door-activated plunger light switch controls the interior lamp by turning it on when the door opens and off when it closes, restoring proper interior illumination and preventing lights from staying on or failing to light. What it does:

• Detects door position and completes the circuit to power the interior light when the door opens.
• Replaces a worn, stuck, or broken door light switch that prevents the lamp from turning on.
• Common symptoms: interior light does not turn on, light stays on continuously, or light works intermittently.
• Simple, direct replacement for the door-mounted lamp switch assembly.

• Disconnect power or unplug the appliance before servicing to avoid electrical shock.
• Access the switch from the door liner or hinge area; basic hand tools (screwdriver) are typically required.
• Handle the switch and wiring gently; confirm correct wiring orientation before reconnecting power.

This dual infinite switch controls heat settings for a range's surface element, letting you adjust cooking temperatures smoothly and reliably. It replaces a worn or failing infinite control to restore variable burner power. What it does:

• Selects variable power levels for a dual (dual-ring) surface heating element
• Allows smooth adjustment from low to high heat for cooking tasks
• Stops responding or prevents element from heating when the switch fails
• Can cause uneven or no heat and intermittent element operation if defective

• One dual infinite switch

• Disconnect power at the breaker before starting work to avoid shock
• Remove the cooktop or back panel and control knob to access the switch
• Verify correct switch orientation and wiring match the old part before fastening

This surface element control replaces the damaged or worn control that regulates heat to an electric cooktop burner. Restores reliable power and heat adjustment for a single surface element on compatible ranges. What it does

• Acts as the infinite switch that controls the burner's heat level based on the knob setting.
• Replaces a control that causes a burner to stay off, fail to heat, or not respond to knob changes.
• Helps eliminate intermittent heating, erratic temperature changes, or a burner that won't cycle properly.
• Works with the corresponding burner element and knob to provide stepped heat control.

• Disconnect power to the range at the breaker before starting any repairs.
• Basic hand tools required; remove the cooktop or rear console per your model's service instructions.
• Handle terminals and wiring carefully; match wire locations exactly during reassembly.

A push-button switch that restores user control functions by completing or breaking electrical circuits. Replaces a worn or failed control switch to help restore normal operation and user input response. What it does:

• Acts as the user-operated control input to start or stop a function when pressed
• Opens or closes the electrical circuit that enables the associated control or feature
• Common symptom: unresponsive controls or functions that do not start when buttons are pressed
• May cause intermittent operation or no response if contacts are worn or corroded

• One replacement push-button switch

• Disconnect power to the appliance before attempting any service
• Use appropriate tools and basic electrical safety; avoid bending terminals or forcing the new part into place