Frigidaire Range Parts

This burner seal is a replacement gasket that fits around a cooktop burner to help keep the burner area sealed and easier to clean. It helps maintain a proper seal between the burner base and the cooktop surface. What it does:

• Seals the gap between the burner and cooktop to limit food, grease and liquid from entering the burner cavity
• Helps keep the burner seated and reduces wobble or misalignment
• Supports cleaner cooktop surfaces and simplifies wipe-downs
• Can help maintain consistent ignition area by keeping debris away from the burner base

• Turn off power to the appliance and ensure the cooktop is completely cool before starting.
• Remove burner grate and lift off the burner cap and burner head as needed to access the seal.
• Clean the seating area of any grease or debris, then press the new seal evenly into place before reassembling.

Main electronic control board that manages the refrigerator's control functions and user interface, helping regulate cooling, defrost, fans, and lights. Replacing a failing board restores control when the unit has unresponsive controls or erratic cycles. What it does:

• Routes power and control signals to compressor, evaporator/condenser fans, defrost heater, lights and other system components.
• Interprets user inputs and runs timed cycles; failure can cause unresponsive buttons, blank or incorrect display, or loss of user control.
• Faulty boards may lead to no cooling, continuous run, frequent cycling, or failed defrost cycles.
• Does not include sensors or wiring harnesses unless explicitly listed for this PN.

• Disconnect power (unplug or shut off breaker) before accessing or removing the old board.
• Handle the board carefully and avoid touching component leads; use anti-static precautions if available.
• Keep all mounting hardware and note connector positions to ensure correct reassembly.

Electronic control restores digital control of refrigerator settings by receiving inputs and sending signals to temperature and system components. Replaces an unresponsive or malfunctioning control board to help restore predictable user control and operation. What it does:

• Interprets user inputs and sensor signals to manage compressor, fans, defrost cycles, and lighting control
• Regulates timing and on/off control for cooling and defrost functions
• Commonly replaced when controls are unresponsive, display is blank or erratic, or cooling cycles behave inconsistently
• Used to correct intermittent or failed electronic control behavior tied to user-interface and system timing

• Disconnect power to the appliance before beginning any service
• Handle the board as a static-sensitive electronic component; avoid rough handling and contact with terminals
• Installation typically requires removing interior panels and unplugging the wire harness; retain fasteners for reassembly

A fixed natural gas orifice that meters fuel to a cooktop or oven burner to help maintain the correct flame size for reliable ignition and consistent heating. Replaces a worn or damaged natural-gas orifice to restore normal burner performance. What it does:

• Regulates the flow of natural gas to a burner for proper flame shape and heat output.
• Helps address weak, uneven, or low flames and burners that take longer to reach set temperature.
• Works at the burner valve/orifice holder to maintain steady ignition and cooking performance.
• Intended for natural gas systems only—use LP/propane orifices only when a verified conversion has been performed.

• Before servicing, shut off the gas supply and electrical power to the appliance.
• Replace only with the correct OEM or equivalent orifice size; do not force or overtighten.
• After installation, check all connections for leaks.

This Main top is the oven's upper cabinet panel that provides the flat surface and structural support for the cooktop area, restoring proper fit and appearance. It replaces a bent, damaged, or corroded top to help the range sit and seal correctly. What it does:

• Replaces the damaged or warped top panel that supports the cooktop and front controls
• Restores a flat, even surface to prevent gaps and improve alignment with adjoining panels
• Helps prevent heat and moisture from reaching internal components through damaged metal
• Commonly replaced when the top shows dents, rust, or mounting-point damage

• One Main top (upper cabinet panel) as shown

• Basic disassembly of the cooktop and control panel is typically required; disconnect power before starting
• Handle edges carefully; metal panels can be sharp
• Keep hardware organized for reassembly; reuse original screws and brackets unless damaged

This control knob restores secure, tactile operation to a damaged or missing appliance control. It makes setting selection easy and helps return the control shaft to safe, predictable use. What it does:

• Replaces a worn, cracked, or missing control knob to restore manual control
• Provides a firm grip and detent feedback for accurate setting selection
• Fits directly onto the control shaft to enable normal operation of the control
• Useful when a knob is loose, won't turn, or is cosmetically damaged

• Disconnect power (unplug or turn off breaker) before servicing electrical appliances
• Pull the old knob straight off the control shaft and push the replacement on until fully seated
• If the new knob won't seat, inspect the control shaft and any retained insert for damage before forcing

A replacement igniter with plug for gas ovens and ranges that lights the burner by glowing until the gas ignites. Restores reliable ignition so burners and bake/ broil functions heat properly. What it does

• Glows to ignite gas for oven or range burners so the appliance reaches cooking temperature.
• Commonly used when the oven won't light or takes too long to ignite.
• Replaces a cracked, broken or failed igniter that no longer produces consistent heat.
• Works with the oven's gas valve and control system to start normal heating cycles.

• Disconnect power and turn off the gas supply before starting work.
• Handle the ceramic/glow tip carefully; oils or cracking can cause premature failure.
• Verify connector seating and routing to avoid contact with metal or moving parts.

This door gasket creates an airtight seal around the refrigerator door to help maintain proper cooling and energy efficiency. Replaces a worn, torn or hard-to-close seal to reduce moisture and keep food fresher. What it does:

• Seals the door perimeter to help maintain consistent internal temperatures
• Prevents warm, humid air from entering and forming frost or condensation
• Helps the compressor run less frequently by improving cabinet efficiency
• Reduces drafts, cold spots and premature spoilage caused by a damaged seal

• Clean the door channel and remove old gasket before fitting the new seal
• Warm the gasket with a hair dryer (low setting) if needed to make installation easier

Color: chrome. Measures about 18 inches wide by 15 inches deep.

This safety valve controls and shuts off gas flow to the appliance burner assembly to help prevent unintended gas delivery. It restores safe operation when a failed valve is replaced and the ignition system is working properly. What it does:

• Regulates and stops gas flow to the burner/oven when the valve is closed
• Prevents gas from reaching the burner when ignition is off or unsafe conditions occur
• Common symptom fixes: no heat, continuous clicking with no ignition, or a persistent gas smell when appliance is trying to light
• Works with the appliance's ignition and pressure systems to maintain safe fuel delivery

• Turn off gas and power at the appliance before starting work
• Use appropriate tools and follow the appliance service manual; fittings may require thread sealant rated for gas
• After installation, check all connections for leaks with a non-corrosive leak detector or soapy water; do not use an open flame

Replacement machine screw used to secure appliance panels and internal components, restoring a stable fit and reducing rattling. Matches a 10-32 thread with a 17/32-inch length for original fastener locations. What it does:

• Fastens panels, trim pieces, and internal brackets; a missing or damaged screw can cause loose panels or rattling noises.
• Secures knobs, control housings and small assemblies to prevent wobble or misalignment.
• Restores proper fit for components so doors and access panels sit evenly and function reliably.

• Disconnect power (unplug or shut off circuit) before accessing components.
• Use the correct driver and tighten by hand; avoid overtightening to prevent stripped threads or cracked plastic.
• Keep any original washers or clips and reinstall them with the screw.

This hinge kit restores a refrigerator door's secure attachment so the door opens, closes and seals properly. Install to correct sagging, misalignment or noisy pivot points and help maintain consistent cabinet closure. What it does:

• Secures the appliance door to the cabinet and provides the pivot point for smooth movement
• Restores proper door alignment to help improve sealing and reduce air gaps
• Replaces worn or bent hinge hardware that can cause door sagging or rubbing
• Reduces creaks, binding or uneven door movement when operating the door

• Disconnect power to the appliance and remove food from the door before starting
• Support the door during removal and installation to prevent drops or damage
• Tighten hardware securely but avoid over-torquing; verify door alignment and seal after installation
• Follow OEM instructions for your model before ordering

The Knob is an OEM part for Frigidaire ranges. It is responsible for controlling the various functions and settings of your range, allowing you to adjust the temperature and operate the burners.

A bad knob can occur due to wear and tear over time, accidental damage, or exposure to heat and moisture. Signs of a faulty knob include difficulty in turning, a loose or wobbly fit, or the control markings wearing off.

Symptoms of a bad knob include:

• Difficulty in turning or adjusting 
• The knob feeling loose
• Cracks or discoloration 

Replace your worn-out or damaged range knob with this genuine OEM Frigidaire part to restore your range. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

Color: White

This glide restores smooth, aligned movement for a refrigerator or freezer drawer so the drawer opens and closes without sticking. Use it to replace a worn or broken glide and reduce scraping, binding, or uneven travel. What it does:

• Guides and supports the drawer so it tracks straight and slides smoothly.
• Replaces worn or damaged glides that cause drawers to stick, bind, or scrape.
• Helps prevent the drawer from coming off the track or shifting out of alignment.
• Reduces noise and uneven movement during opening and closing.

• Disconnect power (unplug the appliance) before servicing to avoid electrical hazards.
• Remove the drawer and any obstructing shelves per the OEM instructions to access the glide.
• Keep or replace original mounting screws; ensure the glide is oriented and seated correctly before tightening.
• Replace those parts to ensure a secure fit.