Frigidaire Range Switch

This wiring harness assembly routes power and signals between the appliance control and electrical components so the unit operates reliably. It replaces a damaged or burnt harness to restore proper electrical connections and reduce intermittent faults. What it does:

• Connects controls, switches and motors to the main power and control board
• Restores interrupted circuits that can cause intermittent operation or component failure
• Helps resolve symptoms like lights, fans or motors not running or responding
• Replaces frayed, melted or corroded wiring that creates shorts or open circuits

• Disconnect power to the appliance before servicing to avoid shock or injury
• Handle connectors by the plug bodies; avoid pulling on wires
• Route and fasten the harness exactly as the original to prevent chafing or heat exposure

This replacement switch restores reliable control of a specific circuit or feature in your appliance. A button, selector, or lever that has become unresponsive or intermittent can be fixed by installing a new switch.

• Opens and closes an electrical circuit to power the intended component or feature
• Helps resolve no-response or intermittent operation from a selector or button
• Addresses issues like a stuck/broken actuator or a switch that only works when wiggled
• Supports safe, consistent control of the appliance function

• Disconnect power to the appliance before servicing
• Note wire positions and transfer one lead at a time to the matching terminals
• Seat the switch fully in its mounting; avoid pinching or straining wires
• After reassembly, restore power and test operation; use a multimeter to confirm continuity if needed

The Surface Element Control Switch is an OEM part for Frigidaire ranges. It is responsible for regulating the heat output of the surface elements on your range, allowing you to adjust the temperature for different cooking needs.

A bad surface element control switch can be caused by wear and tear, electrical issues, or component failure. When the control switch becomes faulty, it can result in issues such as the surface elements not heating up, inability to adjust the temperature, or inconsistent heat output.

Symptoms of a bad surface element control switch include:

• Surface elements not heating up
• Inability to adjust the temperature of the elements
• Surface elements heating unevenly or inconsistently

Replace your faulty surface element control switch with this genuine OEM Frigidaire part to restore your range's surface elements. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

Electronic control board that operates the appliance's user interface, timers and cycle selection to restore responsive controls and correct program sequencing. Replacing a failed control returns normal cycle selection and display function. What it does:

• Manages user inputs, display indicators and electronic cycle logic for the appliance.
• Starts and stops cycles, sequences timers and communicates status to other modules.
• Common symptom fix: blank or unresponsive display, inability to select cycles, or erratic/electronic control behavior.
• Replacing this board fixes faults caused by failed or intermittent electronic control components.

• Disconnect power before beginning any repair to avoid shock or damage.
• Handle the board by its edges and avoid static discharge; use anti-static precautions if available.
• Verify connector alignment and secure mounting; replace screws and retainers as removed.

This rotary selector switch lets the appliance select between functions or cycles by turning the control to the desired setting. It restores reliable, tactile selection and stable electrical contact for normal operation. What it does:

• Provides a rotary contact point to change modes, cycles or heat/cool settings
• Re-establishes reliable electrical connection when worn or intermittent switching causes erratic operation
• Stops slipping, sticking, or loss of detents that prevent proper selection
• Helps resolve no-response or incorrect-function symptoms when the control is turned

• One selector switch

• Disconnect power (unplug or shut off breaker) before attempting service
• Access may require removing the console or control panel—keep fasteners and hardware organized
• Handle contacts and terminals carefully; avoid bending or contaminating connections
• Test operation after reassembly

This electronic control board manages oven functions and the user interface so the range heats and cycles correctly. It replaces a faulty control assembly to restore timed baking, temperature control and display response. What it does:

• Receives user commands from the front panel and runs the oven's timed bake/clean cycles
• Regulates heating elements by switching relays based on temperature input
• Drives the display and touch/keypad so settings and error messages appear
• Common symptoms: oven won't heat, display is blank or unresponsive, or cycles fail to start

• Disconnect power at the breaker before accessing or replacing the control board
• Handle the board carefully to avoid static damage and avoid contact with component leads
• Retain all mounting hardware and wire routing; match connectors during reassembly