Frigidaire Refrigerator Relay, Overload, Capacitor

This Temperature Controller regulates cooling by switching power to the compressor and related circuits to hold the set temperature. Replacing a failing controller restores accurate temperature control and reliable operation. What it does:

• Cycles cooling components to maintain the temperature you set
• Helps keep cabinet temperatures consistent for proper food storage
• Coordinates on/off operation to prevent overcooling or warm conditions
• Common failure symptoms: too warm or too cold, runs constantly or won't start, control/dial unresponsive

• 1 temperature controller

• Disconnect power before servicing—this is a line-voltage control
• Access the control area, label or photograph wire positions, and move wires one at a time to the new controller
• Reuse existing mounting hardware and any knob/overlay as applicable
• After install, set to mid setting and allow up to 24 hours for temperatures to stabilize

This compressor overload is a thermal/protective device that helps prevent compressor damage by cutting power when the motor overheats or draws excessive current. It restores normal operation once conditions return to safe levels. What it does:

• Protects the refrigerator compressor from overheating and electrical overloads
• Works with the compressor start relay to help the motor start and run properly
• Common symptom linkage: replaces a failed overload when the compressor hums but won't start
• Stops compressor cycling or prevents repeated trips that cause cooling loss

• One compressor overload (single piece as shown)

• Disconnect all power before replacing to avoid shock or injury
• Handle terminals carefully and reconnect matching terminal positions
• Replace only with the same part number or equivalent
• If compressor still won't start after replacing the overload, check the start relay and compressor condition.

This compressor start relay helps the refrigerator compressor start and run more reliably, restoring proper cooling performance and preventing frequent hard starts. Fits compatible Frigidaire-style compressors and connects at the compressor terminal block. What it does:

• Provides the initial boost to spin the compressor motor during startup
• Helps prevent the compressor from stalling or failing to start
• Can reduce clicking, humming, or a fridge that runs but does not cool
• Works with the compressor's start circuit to engage the motor quickly

• Disconnect power to the appliance before inspecting or replacing the relay
• Access the relay at the compressor (usually mounted on the compressor body); note terminal positions before removal
• Replace only with the exact relay specified by the manufacturer; secure all connections and wiring

This electronic control board is the refrigerator's main circuit board that manages temperature, defrost and user controls—restoring responsive control functions and resolving erratic or non-working control behavior. What it does:

• Controls compressor, fans and defrost cycles by sending signals based on sensor inputs
• Manages user interface commands and display response
• Can stop fridge cooling or cause incorrect temperatures when failing
• May cause intermittent operation, no display response, or failure to complete defrost cycles

• Disconnect power to the appliance before starting any work to avoid electrical shock
• Handle the board by its edges and avoid touching components or connector pins
• Verify connector orientation and seating; replace exactly like-for-like to ensure compatibility

This compressor overload is a replaceable start-protection device that helps prevent compressor overheating and electrical damage. Replacing a failed overload restores reliable compressor starting and helps the refrigerator return to normal cooling. What it does:

• Protects the compressor by interrupting current if the compressor draws excessive current or overheats.
• Works with the compressor start relay to help the compressor start and run normally.
• Common symptoms of a failing overload: refrigerator not cooling, compressor won't start or hums, repeated clicking or tripping.
• Small, service-replaceable part located at the compressor terminals.

• Disconnect power to the appliance before accessing the compressor and its terminals.
• Handle wiring and terminals carefully; note lead locations or take a photo before removal to ensure correct reinstallation.
• If mounting hardware or connector types differ, do not force parts.

This overload protector helps prevent compressor damage by interrupting power when the compressor draws excessive current or overheats. It's a safety device used with the compressor start relay to protect the refrigeration system and improve reliability. What it does:

• Stops compressor current when overheating or electrical overload is detected
• Works with the start relay to allow safe compressor start and operation
• Can address symptoms such as a refrigerator that hums but the compressor won't run, intermittent cooling, or frequent compressor cycling
• Helps prevent compressor burnout by interrupting power during fault conditions

• One overload protector

• Disconnect all power before servicing; risk of shock and equipment damage
• Replace only with the same part number or OEM-specified equivalent
• Handle terminals carefully; ensure secure, corrosion-free connections