Frigidaire Washer Parts

The Agitator is an OEM replacement part for Frigidaire washing machines. This component is responsible for moving clothes during the wash cycle, ensuring that water and detergent are evenly distributed for effective cleaning. The agitator's motion helps to loosen dirt and stains from fabrics. The agitator measures approximately 17" tall

Causes of a bad agitator can include wear and tear over time, damage from washing heavy or unbalanced loads, or issues with the agitator’s internal mechanisms that reduce its efficiency.

Symptoms of a bad Agitator include:

• Clothes not getting properly cleaned
• The washing machine making unusual noises during the wash cycle
• The agitator not moving or moving erratically
• Visible damage or cracks on the agitator

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Drum Drive Belt is an OEM part for Frigidaire dryers. It connects the drum to the motor, enabling the drum to rotate and tumble the clothes during drying cycles. The belt is 54 inches long and 5/8 inches wide

You should replace this drum drive belt if it becomes worn out, frayed, or broken due to the high heat and friction involved in the drying process. Additionally, improper loading or overloading of the dryer can cause the belt to stretch or snap.

Symptoms of a bad drum drive belt include:

• Dryer drum not turning
• A loud thumping or squealing noise during operation
• Dryer stopping mid-cycle
• Clothes remaining wet after the drying cycle

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Inner Door Frame is an OEM part for Frigidaire front-load washing machines. It is located on the inner side of the washer door and provides support and stability to the door assembly. It helps secure the door components, such as the glass window and door seal and ensures proper alignment and functionality.

Causes of a faulty inner door frame can include wear and tear over time, physical damage, or misalignment. These factors can result in issues such as a loose or misaligned door, difficulty in closing or opening the door, or water leaks during the wash cycle.

Symptoms of a bad inner door frame may include:
• Loose or wobbly door
• Difficulty in closing or opening the washer door
• Water leakage during the wash cycle

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Spin Bearing is an OEM part for Frigidaire washing machines, specifically designed to facilitate the smooth and efficient rotation of the washer drum. This bearing plays a pivotal role in the operation of your washing machine, allowing the drum to spin freely with minimal friction and noise.  

Causes for replacement may include wear and tear from regular use, water damage leading to rust or corrosion, or physical damage from excessive load sizes. 

Symptoms of a bad Spin Bearing include:

• Loud noises during the spin cycle, often described as grinding or rumbling
• The drum struggling to spin or not spinning as smoothly as it should
• A noticeable decrease in washing performance due to the drum's impaired movement

This genuine Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore gas ranges.

The Bellows is an OEM replacement part for Frigidaire front-loading washing machines. Also known as the door boot or gasket, the bellows forms a seal around the washer door during cycles. It prevents water leaks that could damage components.

Causes of a bad bellows can include cracks or punctures resulting from years of opening and closing the washing machine door during regular laundry loads. Mineral buildup may also degrade flexibility over time.

Symptoms of a bad bellows include:

• Water leaks visible around the washing machine door
• Puddles or water marks found inside or below the unit
• Unusual noises or vibrations accompany leaking

This Frigidaire replacement is compatible with some Electrolux, Gibson, and Kenmore front load models as well.

The Water Inlet Valve Assembly is an OEM part for Frigidaire washing machines. This assembly controls the flow of water into the washing machine during the fill cycles, ensuring the correct amount of water enters the tub.

Over time, the water inlet valve can become faulty due to mineral buildup, wear and tear from frequent use, or damage to the valve components. If the valve is not functioning properly, it can result in issues with the water flow into your washing machine.

Symptoms of a bad water inlet valve assembly include:

• No water entering the washing machine
• The washer filling slowly or not at all
• The washing machine filling with water when it is turned off
• Leaks from the valve area

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Drain Pump is an OEM replacement part for Frigidaire front load washers. Located inside the base of the washing machine tub, it actively pumps out water through the drain hose after each cycle completion. Efficient drainage is vital for preventing standing water issues.

Causes of a bad drain pump can include mineral or scale buildup within the pump chamber or impeller over time. The water valve may fail to open fully, blocking drain flow. Bearings may wear, causing the impeller to jam.

Symptoms of a bad drain pump are:

• Incomplete water draining after the cycle
• An accumulation of water remaining in the tub
• Leaking from the base
• Error codes could indicate drainage problems.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore.

The High Temp Lubricant Tube is an OEM part for Frigidaire appliances, specifically designed to withstand and operate under high temperature conditions. This lubricant is essential for the proper maintenance and functionality of various Frigidaire appliances, offering protection against heat and friction. 

Over time, the lubricant can degrade or become contaminated, which can compromise its effectiveness. Causes of a bad high temp lubricant include exposure to extreme temperatures, accumulation of dirt and debris, or simply the natural breakdown of the lubricant over prolonged use.

Symptoms of needing a new High Temp Lubricant Tube include:

• Increased noise during appliance operation
• Reduced efficiency or performance of the appliance
• Harder movement of parts that should glide smoothly

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Detergent Drawer is an OEM part for Frigidaire washing machines. It holds and dispenses detergent at the appropriate times during wash cycles. The drawer is designed with compartments to separate powder and liquid detergents for optimized cleaning.

Causes of a bad detergent drawer can include leaks from cracks in the plastic material, malfunctions in the electronic components that control dispensing, or damage to the drawer itself.

Symptoms of a bad Detergent Drawer include:

• Incorrect or insufficient detergent amounts dispensed during cycles
• Residue, puddles, or leaks of detergent inside the washer tub or housing
• Odors or mold growth near the detergent area
• The drawer failing to open or close fully

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Drawer Latch is an OEM part for Frigidaire pedestals. This latch closes storage or pedestal drawers in the base. It creates a tight seal around each drawer, protecting contents from dust and spills.

Issues tend to arise from normal wear over years of use. Drawers opening and closing put stress on latches. Nearby laundry vibrations may also contribute.

Symptoms of a problematic pedestal drawer latch include:

• Drawers that do not fully latch or do not stay closed properly
• Gaps that allow debris or moisture to enter the storage compartments
• Loose or misaligned drawers that are difficult to open and close

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore ranges.

The Water Level Pressure Switch is an OEM replacement part for Frigidaire washing machines. It senses the water level in the washer tub and signals to the control board when the tub is full. 

Symptoms of a faulty pressure switch include:

• The washer not filling or draining properly  
• No flow detection resulting in improperly filled or drained loads
• Unexpected or premature terminating of cycles
• Potential leaks from overfilling due to failed level sensing  

Causes can be normal wear over time exerting pressure on internal components, moisture exposure damaging electrical circuits, or impacts disrupting accurate pressure monitoring.

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. 

The Suspension Spring Kit is an OEM replacement part for Frigidaire front-loading washing machines. These suspension springs are positioned at the top front of the washer, underneath the tub, to help support the weight of the drum during operation.

Over many cleaning cycles, suspension springs can wear down and lose their ability to dampen vibration.

Symptoms of bad suspension springs include:

• Excessive shaking or rattling of the washing machine
• Loud banging or knocking noises coming from inside the washer
• The tub moving excessively during washing and spinning

It is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

This is a motor control board for a washing machine. It comes with the board, tape, bracket, and screw mounted on control. In most cases, this part is located on the bottom of the appliance near the drive motor. The purpose is to control the speed of the drive motor. It also works to determine the direction of the tumble and spin actions while a cycle is in process. If the washing machine is pumping but does not spin, this is often the result of a malfunctioning motor control board.If the motor control board has gone bad, it should be replaced. To replace it, make sure the washer is unplugged or the circuit breaker has been turned off. Pull the washer away from the wall, remove the knobs from the front and screws from the back, and lift the control panel. This offers access to the motor control board, which should be removed so the new part can be installed.This motor control board is made for use with washing machines by Electrolux, Frigidaire, Crosley, and Kenmore. It is sold on an individual basis. This is an authentic OEM replacement part that is directly sourced from the manufacturer.

The Tub to Pump Hose is an OEM replacement part for Frigidaire washing machines. This hose connects the tub to the pump, allowing water to be drained out of the tub and into the drainage system. 

Causes for a malfunctioning Tub to Pump Hose can include blockages from lint or small objects, cracks or holes in the hose material, or loosening of the hose clamps that secure it in place.

Symptoms of a bad Tub to Pump Hose include:

• Water leaking from the bottom of the machine
• Slow or incomplete drainage
• Unusual noises during the drain cycle
• Error messages related to water drainage

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Shock Absorber Mounting Pin is an OEM part for Frigidaire washing machines. It is a part that secures the shock absorber in place, ensuring proper absorption of vibrations and shocks during the washing cycle.

Causes of a bad shock absorber mounting pin can include loosening over time due to constant movement and vibrations, accidental damage or loss during repair or maintenance, or general wear and tear.

Symptoms of a bad or missing shock absorber mounting pin include:

• Excessive shaking or vibrating during the wash cycle
• Loud banging or rattling noises
• The washer moving or "walking" across the floor
• Premature wear or damage to the shock absorbers and other components

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Inner Bellow Spring Clamp is an OEM replacement part for Frigidaire front-loading washing machines. It anchors the interior bellow seal in the proper sealing position.

Causes of replacement include torsion fatigue from years of door opening/closing stresses. Mineral buildup may also restrict needed tension if left unchecked.

Symptoms consist of:

• Visible water leakage from the base of the washer door during active cycles
• Looseness permitting shifting or twisting of bellow position
• Inability to achieve proper water-tight integrity checks

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore ranges.