General Electric Cooktop Switch

The Switch/Wire Harness is an OEM part for GE gas cooktops featuring digital controls. It relays input signals between interactive panels and control modules. 

Causes of failure involve physical stress cracks from repeated flexing, pinched wiring compromising conductivity, and insulation degradation over extended use.

Symptoms of a faulty harness include:

• Unresponsive burner/knob selections   
• Inability to adjust flame heights or temperatures accurately
• Intermittent or unstable power to ignition/control systems

This OEM part is also compatible with Hotpoint and RCA gas cooktop models.

This ignition switch controls the spark to your gas burner or oven igniter so burners light reliably when you turn the control. Replacing a faulty switch can restore consistent ignition and safe operation. What it does:

• Sends the electrical/spark signal to the igniter so the burner lights
• Used when a control knob produces a spark to ignite a gas burner
• Common symptom: burner won't light or requires multiple attempts to ignite
• Common symptom: control produces no spark or feels intermittent when turned

• Disconnect power and shut off the gas supply before servicing
• Label and photograph wiring before disconnecting to ensure correct reconnection
• Inspect connector and mounting; test for continuity with a multimeter if troubleshooting

This electronic control regulates oven functions and user commands, restoring reliable cycle selection, timing and temperature control when the original control fails. Designed as a direct-replacement control assembly for affected 2400-series ranges. What it does:

• Manages oven cooking cycles, timers and user interface inputs so settings run as selected
• Sends and receives signals to heating circuits and sensors to control temperature and run cycles
• Helps stop symptoms like a blank or flashing display, unresponsive buttons, or an oven that won't start or won't stop heating
• Restores normal electronic control behavior when the original board is damaged or fails

• Disconnect power (unplug or shut off breaker) before accessing the control — risk of electric shock
• Label or photograph wiring before disconnecting to ensure proper reconnection; handle the board by its edges to avoid damage
• Test functions after reconnecting power

This infinite control switch governs the heat output of an electric cooktop burner, letting you select variable heat settings for precise cooking. Replaces a worn or non-responsive burner control to restore smooth temperature control. What it does:

• Regulates power to an electric surface element for variable heat levels
• Allows dialed adjustments from low to high for simmering or boiling
• Commonly replaces switches that click, don't change heat, or fail to hold a setting
• Works with compatible surface element controls and wiring harnesses

• One infinite control switch

• Disconnect power at the breaker before accessing the range or cooktop
• Handle with care; avoid bending terminals or damaging the shaft and mounting tabs
• Verify correct knob and switch alignment during reassembly; test function before full use

This burner box wiring harness connects the cooktop/oven burner components to the appliance's control systems, restoring reliable ignition and power routing for the burner box area. Use to replace a damaged or burnt harness for safer operation. What it does

• Routes electrical connections between igniters, sensors, switches, and control modules in the burner box
• Restores ignition or heating when a frayed or open harness prevents burners from sparking or heating
• Replaces harnesses with cracked insulation or melted connectors that can cause intermittent operation or arcing
• Helps eliminate electrical shorts and poor contact at connector plugs inside the burner box

• One burner box wiring harness as shown

• Disconnect all power (electrical and gas) before servicing; verify power is off
• Inspect connectors and routing in the burner box, replacing any mounting clips or fasteners if damaged
• Ensure correct connector seating and secure wiring away from high-heat components

This fan relay is an electrical replacement part that restores the relay control for the refrigerator/freezer fan motor so the appliance can circulate air properly and maintain even cooling. Use it to replace a failed relay and return fan operation. What it does:

• Switches electrical power to the evaporator/condenser fan motor when the control calls for airflow
• Commonly used when the fan won't start, runs intermittently, or the appliance struggles to maintain temperature
• Helps stop clicking or repeated start attempts caused by a bad relay
• Works as the control interface between the main control and the fan motor

• One fan relay

• Always unplug the appliance before starting any repair to avoid shock risk
• Locate the relay on the compressor or control module per your model's service guide and note connector positions before removal
• Transfer wiring/plug connectors exactly; avoid bending pins or over-tightening fasteners

The Fan Switch is an OEM replacement part for GE cooktops. Measuring approximately 2 inches by 1 inch, this fan switch serves as a component in activating the downdraft fan. The downdraft fan aids in extracting smoke, steam, and odors, promoting a cleaner and fresher cooking environment.

A malfunctioning Fan Switch can be attributed to electrical issues, wear and tear from regular use, or physical damage. These problems can lead to the downdraft fan not activating, resulting in inadequate ventilation and the accumulation of smoke and odors during cooking.

Symptoms of a bad Fan Switch include:

• The downdraft fan failing to activate, leading to poor ventilation
• Accumulation of smoke and odors during cooking
• The switch being unresponsive or failing to maintain the fan’s operation

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This spark switch/simmer burner is the electrical switch that sends spark to a gas cooktop burner, restoring reliable ignition and simmer control for compatible ranges. Replaces a worn or unresponsive burner spark switch. What it does:

• Routes high-voltage spark to the burner so the gas will ignite
• Enables proper simmer flame control and consistent ignition
• Commonly replaced when a burner won't spark, sparks intermittently, or won't light
• Works with the range's control knob and ignition system to start the flame

• One spark switch/simmer burner

• Disconnect power to the appliance and turn off the gas supply before beginning work
• Access typically requires removing the cooktop or control panel; follow your model's service instructions
• Handle electrical connections carefully and replace only with the correct part number

This infinite surface burner switch controls the variable heat output for a cooktop surface element, letting the burner cycle through low-to-high heat settings for normal cooking. It restores responsive temperature control when the burner won't regulate. What it does:

• Regulates power to a surface heating element for adjustable heat from low to high
• Causes symptoms like a burner that won't heat, won't change temperature, or only works at one setting
• Replaces a failed or intermittent control that makes the knob feel loose or non-responsive
• Works with standard single-element surface heating circuits

• One infinite surface burner switch

• Disconnect power at the breaker before replacing electrical components
• Basic hand tools required; access may require removing the cooktop or burner assembly