General Electric Plug Or Insert

This reversible door plug fills the unused mounting hole when you switch the door swing on your refrigerator. It restores a finished appearance and helps keep air and moisture from entering through the opening.

• Covers the unused door hole created during a door swing reversal
• Helps maintain proper sealing and resists drafts/condensation at the opening
• Restores a clean, finished, factory look to the door
• Common symptoms: missing or cracked plug, exposed hole, cosmetic gap on door edge

• Disconnect power before servicing any door components
• Gently pry out the old plug with a plastic trim tool to avoid scratches
• Align the new plug with the opening and press until fully seated and flush
• Verify the door closes properly and the gasket seals evenly

This plug button is a small snap-in cap used on refrigerators to cover exposed holes on door handles, liners, or trim. It restores a clean, finished look while helping keep dust and moisture out of the cabinet.

• Snaps into a screw or access hole on a handle, liner, or trim panel
• Covers fasteners and gaps for a clean, finished appearance
• Helps block dirt and moisture from open holes
• Typical symptoms: missing cap, broken or loose plug, visible screw hole or cosmetic gap

• Unplug the appliance before servicing and use caution around sharp edges
• Align the plug with the hole and press straight in by hand until fully seated and flush
• For handle screw holes, tighten fasteners first, then install the cap
• Avoid using metal tools on finished surfaces to prevent scratches

A replacement reversible plug door that covers and protects the appliance power inlet while letting the cord exit left or right for tidy cord routing. Restores a clean back panel appearance and helps keep the power connection protected from debris. What it does:

• Covers the power inlet opening to protect the plug and inlet from dust and debris.
• Reversible design lets you route the power cord to either side to fit against the wall.
• Helps keep the cord tucked close to the appliance so the unit can sit flush with cabinetry or walls.
• Replace when the door is cracked, broken, missing, or no longer holds the plug securely.

• Always unplug the appliance before starting any repair or inspection.
• May require access to the rear panel; check your owner's manual for disassembly steps.
• Check orientation before finalizing installation to ensure correct left/right cord routing.

This plug button is a replacement cosmetic/functional cap that covers an unused control opening or receptacle on the appliance, restoring a finished appearance and helping keep out dust and debris. What it does:

• Covers and seals an unused control hole or plug location to improve appearance
• Helps prevent dust, lint, and small debris from entering the opening
• Restores a flush, finished look when a switch, knob, or connector is missing
• Simple snap-in design for a clean, low-profile result

• Disconnect power to the appliance before servicing.
• Typically snaps into place; no special tools required for most installations.
• If removal is needed, use a plastic pry tool to avoid scratching surrounding surfaces.
• Your appliance owner's manual or parts diagram to correct placement.

This exterior drain plug seals the washer's drain opening to prevent leaks and contain water in the tub during operation. It provides a simple replacement to restore a watertight seal at the appliance drain area. What it does:

• Seals the drain opening to help prevent water leaks from the tub or drain housing
• Helps maintain proper drainage by keeping debris out of the drain path
• Can stop visible water weeping or puddling near the base of the washer
• Replaces a cracked, worn or missing exterior drain plug to restore normal operation

• One exterior drain plug

• Disconnect power to the appliance and turn off water supply before starting any work
• Remove the appropriate access panel or lower kick plate to reach the drain opening
• Press or thread the plug into the drain opening as designed; snug by hand and avoid over-tightening
• Inspect the surrounding seal area and replace any damaged gaskets or housings if present; test for leaks after reinstalling panels and restoring power/water

This plug button thimble is a small insulating part that supports and protects a push button or plug terminal, helping maintain a secure electrical connection and preventing wear or arcing. It restores proper button fit and function. What it does:

• Cushions and centers a push button or plug terminal for smooth operation
• Provides electrical insulation to reduce risk of shorting or arcing
• Helps keep the button/plug securely seated to prevent intermittent contact
• Commonly replaced when buttons wobble, stick, or have poor electrical connection

• Disconnect power to the appliance before attempting any repair.
• Replacement typically requires removing the control panel or button assembly; handle plastic parts carefully to avoid cracking.
• Verify orientation and seating before reassembling to ensure proper button movement.

This plug button thimble is a small control-panel insert that secures and centers push buttons, helping keep button caps in place and reducing moisture or debris entry. It restores proper button feel and alignment on the control panel. What it does:

• Centers and retains push-button caps so buttons press and release correctly
• Helps prevent dirt and spills from entering the control-panel opening
• Replaces a cracked, worn, or missing thimble that lets buttons wobble or fall inward
• Compatible with the original push-button assembly to restore original fit and function

• Simple, non-electrical replacement—power to the appliance is not required for this exterior part, but unplugging is recommended if removing trim near live components
• Remove the button cap first, press the old thimble out from the front or back as applicable, then press the new thimble into the panel opening until fully seated
• Inspect button cap and surrounding trim for damage; replace any damaged mating parts for best fit
• Use care to avoid scratching the control panel; keep small parts away from children

This reversible door plug covers the unused hinge or mounting hole after changing a door swing, restoring a clean appearance and helping keep out dirt and drafts. Simple, color-matched replacement for a neat finish. What it does:

• Covers exposed hinge or mounting holes on the door edge for a finished look
• Helps block dust, pests and drafts from entering through unused openings
• Matches original geometry to sit flush with the door surface
• Designed to work with reversible door installations where a hole is no longer used

• One (1) reversible door plug

• No tools are typically required; press plug into the unused hole until it seats securely
• Confirm correct orientation before installing to ensure a flush fit
• Inspect surrounding sealing surfaces and clean area before installation
• If plug is damaged or does not seat properly, replace with the exact part number

This plastic screw plug covers and protects unused screw holes on appliance panels for a clean, finished look while helping keep out dirt and moisture. Simple replacement to restore appearance and prevent debris buildup. What it does:

• Covers exposed screw holes in trim or panels to improve appearance
• Helps block dust and light debris from entering through openings
• Prevents accidental contact with recessed screws
• Useful when replacing panels or removing components where plugs were lost

• One plastic screw plug

• Disconnect power or unplug the appliance before accessing internal panels when necessary
• Press the plug into the hole by hand; use a flat tool gently if alignment is tight
• Do not force or hammer the plug to avoid panel damage
• Replace any damaged surrounding trim before installing plug for a secure fit

This plug is an electrical wire connector that restores a secure, insulated connection between appliance wiring and components. It helps prevent intermittent power loss and reduces the risk of shorts from damaged or loose wiring. What it does:

• Provides a secure mating point for a component or harness to carry electrical power
• Insulates and protects exposed terminals from contact and shorting
• Replaces cracked, melted, or loose connector housings that cause intermittent operation
• Commonly used when a control, sensor, or motor has lost power due to a failed connector

• Always disconnect power at the breaker or appliance plug before inspecting or replacing electrical connectors
• Match the connector shape and terminal count to the existing harness to ensure proper fit
• Inspect surrounding wiring and terminals for heat damage; replace any damaged wires or terminals to prevent recurrence