General Electric Refrigerator Air Duct Or Vent

The Foam Duct is an OEM replacment part for GE refrigerators. It is an insulating conduit located within the fresh food compartment that helps direct chilled air circulation from evaporator coils throughout interior shelves and bins. The foam duct plays an important temperature regulation role by strategically venting cool air where needed.

Causes can involve cracks in rigid duct walls, compressed insulation, or obstructions within the airflow pathway restricting proper circulation

Symptoms of a defective duct include:

• Inconsistent temperatures with warmer/colder spots within the fridge
• Frost or ice buildup on interior surfaces away from coils
• Higher energy bills from the compressor overworking to maintain temps

Compatible with some Hotpoint, RCA, and some Kenmore models.

This replacement air tower assembly is the vertical duct that channels chilled air through the refrigerator compartment. Replacing a damaged tower restores proper airflow to help maintain even temperatures and consistent cooling from top to bottom.

• Directs cold air from the evaporator to vents in the fresh food section
• Helps balance temperatures and reduce warm spots
• Often replaced when the original is cracked, broken, or warped
• Common symptoms: weak airflow from refrigerator vents and uneven cooling in the fresh food compartment

• Disconnect power to the refrigerator before servicing.
• Remove shelves and bins for access; release tabs or remove screws securing the old tower.
• Transfer any clips or sensors from the original, if present; seat and secure the new tower.
• Restore power and verify airflow from the vents.

The duct foam assembly insulates and seals the refrigerator's air duct to keep cold air moving efficiently between compartments. Replacing worn or missing foam helps restore airflow control, reduce moisture at the vent, and stabilize temperatures.

• Seals the air duct to prevent warm-air leaks and maintain proper airflow
• Insulates the duct to help keep fresh-food temperatures consistent
• Helps reduce condensation or frost forming around the vent area
• Typical indications include temperature swings, a warm fresh-food section, moisture/frost near the duct, or visibly damaged/missing foam

• Disconnect power to the refrigerator before servicing
• Remove interior shelves/panels as needed to access the air duct; note foam orientation before removal
• Clean the mounting surface; seat new foam fully and evenly to create a complete seal—do not obstruct a damper door or sensor if present
• Restore power and verify airflow and sealing around the vent

The damper duct assembly regulates the cold air sent from the freezer into the refrigerator compartment. Replacing a worn or sticking damper restores proper airflow and helps the fresh food section maintain stable, even temperatures.

• Regulates airflow from the freezer into the refrigerator compartment
• Helps maintain set temperatures by opening and closing to meter cold air
• Common failure signs: fresh food too warm, items freezing near the vent, weak/no airflow from the vent, or clicking/buzzing from the damper area

• Disconnect power to the refrigerator before servicing
• Remove shelves and the duct/vent cover; retain screws and clips
• Unplug the wire harness and swap the assembly; transfer any reusable hardware
• Ensure seals seat fully to prevent air leaks; restore power and allow temperatures to stabilize

This freezer air duct channels cold air from the evaporator fan through the freezer compartment, helping maintain consistent airflow and temperature. Replacing a cracked or missing duct restores a proper seal and reliable circulation. What it does:

• Directs and contains airflow from the evaporator fan within the freezer
• Helps maintain even cooling and reduces warm-air leaks
• A damaged duct may contribute to weak airflow, frost/ice around the vent, temperature swings, or vibration/rattling
• Restores proper alignment and fit with adjoining air tower/panel components

• 1 freezer air duct

• Disconnect power before servicing; wear cut-resistant gloves
• Access is typically from inside the freezer; remove shelves/ice bin and interior air tower or cover as needed
• Save and transfer any screws, clips, gaskets, or insulation from the original part
• Ensure panels and seals seat tightly after installation to prevent air leaks

This air handler assembly replaces the failed air distribution module to restore proper airflow and circulation in the appliance. Designed as a direct-fit replacement to revive normal heating/cooling performance and fan operation. What it does:

• Houses the blower and air-distribution components that move conditioned air through the unit
• Restores airflow when a damaged or nonworking air handler causes weak or no air movement
• Helps eliminate uneven temperatures caused by a malfunctioning air distribution assembly
• Works with existing controls and ducting when installed as a like-for-like replacement

• One air handler assembly

• Verify power is disconnected before starting
• Handle assembly carefully to avoid damage to blower blades, wiring, or connectors
• Follow OEM instructions and local codes for electrical and mechanical connections

This plenum fan moves cold air from the evaporator into the refrigerator cabinet to help maintain even temperatures and proper cooling performance. It's a direct-replacement evaporator air-moving component. What it does:

• Circulates cold air from the evaporator coil through the refrigerator compartments
• Helps the appliance reach and hold set temperatures for food safety
• Commonly associated with weak cooling, uneven temperatures, or excessive frost buildup when failing
• Works with the evaporator motor system to maintain proper airflow

• One plenum fan (evaporator) assembly

• Disconnect power to the appliance before beginning any repair
• Handle evaporator fins and fan blades carefully to avoid damage
• May require removing interior panels or the evaporator cover; use basic hand tools

This molded duct assembly directs cold air from the freezer compartment into the fresh-food section to help maintain proper airflow and temperature balance. It replaces a damaged or cracked transition duct to restore directed air circulation. What it does:

• Channels freezer-cooled air into the refrigerator compartment for even cooling distribution
• Helps reduce warm spots in the fresh-food area when functioning correctly
• Can prevent excessive frost or ice buildup caused by misdirected airflow
• Supports proper operation of the freezer-to-fridge venting system

• Disconnect power to the appliance before service to avoid electrical shock
• Remove shelves, drawers, and access panels as needed to reach the duct
• Handle the duct carefully to avoid cracking plastic tabs; use appropriate fasteners when reinstalling

This vertical vent duct directs internal airflow inside the cabinet to help maintain consistent temperatures and proper circulation. It replaces a cracked, warped or missing duct to restore designed airflow paths and reduce uneven cooling. What it does:

• Channels cold air between compartments to support even cooling and freezing
• Prevents air leaks that can cause warm spots or extra run time
• Helps maintain proper defrost and frost patterns when installed correctly
• Reduces noise from rattling or vibrating panels if damaged ducts are secured

• Disconnect power to the appliance before starting any repair
• Remove shelves, panels or evaporator cover as needed to access the old duct
• Inspect adjacent seals and fasteners; replace damaged clips or gaskets for best fit
• Reassemble panels securely and test operation; for model-specific instructions

This evaporator fan plenum is the molded housing that channels cold air from the evaporator across the refrigerator compartments, helping maintain even cooling and efficient airflow. It replaces a cracked, damaged, or warped plenum. What it does

• Directs airflow from the evaporator fan to the fresh-food and freezer sections for consistent temperature distribution
• Helps prevent air leaks around the evaporator area that can reduce cooling performance
• Often replaced when the original housing is cracked, broken mounting tabs are present, or airflow is obstructed
• Works with the evaporator fan and ducting to reduce frost buildup caused by disrupted airflow

• One evaporator fan plenum housing

• Disconnect power to the appliance before starting any repair
• Removal typically requires accessing the evaporator compartment and detaching mounting screws and any electrical connectors or duct clips
• Handle carefully; edges may be sharp and mounting tabs can be brittle on older units
• Verify alignment of the plenum with the evaporator fan and sealing surfaces to avoid air leaks after installation