General Electric Refrigerator Guard, Shield, Barrier Parts

This vinyl sleeve fits over a rod, tube, or wire in the refrigerator to protect and cushion contact points. It reduces wear and vibration and helps keep components aligned for smooth, reliable operation.

• Provides a protective barrier at contact points to prevent abrasion or marring
• Helps maintain spacing and alignment for a snug, proper fit
• Cushions to damp vibration and reduce rattles or squeaks
• Replace if the sleeve is missing, cracked, hardened, or if components feel loose or make noise

• Disconnect power; turn off the water supply if working near water lines
• Note the sleeve's original location and orientation; take a photo for reference
• Remove the old sleeve and any debris; slide the new sleeve into the same position
• Check clearance and resecure related parts before restoring power

Lower gasket shield protects and supports the bottom edge of the refrigerator/freezer door gasket for a tighter seal, reducing air leaks and moisture build-up while keeping the gasket aligned for reliable sealing. What it does:

• Protects and secures the lower edge of the door gasket to maintain proper gasket positioning and contact.
• Helps prevent cold air loss, frost buildup, and condensation caused by a misaligned or damaged lower gasket area.
• Provides a mounting surface that keeps the gasket from folding or pulling away at the bottom of the door.
• Replaces worn, cracked, or broken lower shield pieces that can cause visible gaps or sealing issues.

• Disconnect power to the appliance before beginning any repairs and follow manufacturer service instructions.
• Remove the door gasket or lower trim per OEM steps to access the shield; keep fasteners and note orientation for reassembly.
• Do not force plastic parts; if removal is tight, work slowly to avoid cracking the cabinet or new shield.

This ice maker guardrail secures and guides the ice maker/ice bin assembly so cubes dispense and stay aligned. It helps restore proper ice flow and prevents the ice bin from shifting or rubbing during harvest cycles. What it does:

• Holds the ice maker/ice bin in place to prevent movement and misalignment
• Guides ice cubes during ejection for smoother dispensing
• Reduces rubbing or contact that can cause noise or wear
• Helps maintain consistent ice delivery to the bin

• One ice maker guardrail/rail

• Disconnect power (and water supply if applicable) before beginning service
• Remove shelves or ice bin as needed for clear access; keep fasteners for reinstallation
• Install using existing mounting points and hardware; inspect surrounding parts for wear

This drain baffle guides defrost water into the refrigerator drain to prevent puddling and ice buildup, keeping the fresh food area dry and reducing odors. It fits into the freezer/refrigerator drain opening and channels meltwater safely away. What it does:

• Directs defrost and condensation water into the appliance drain to prevent pooling.
• Helps reduce ice formation and standing water inside the fresh food or freezer compartment.
• Minimizes odors by keeping water from collecting under shelves or liners.
• Works with the drain tube and heater to maintain proper drainage.

• Disconnect power before accessing interior panels or removing shelves.
• Remove shelves and the crisper/evaporator cover as needed to reach the drain area.
• Clear any ice or debris from the drain before installing the new baffle to ensure proper flow.

This LED housing cover protects and secures the refrigerator's LED light assembly while helping direct interior light. It replaces cracked or missing housing shields to restore proper light placement and prevent debris from contacting the lamp. What it does

• Protects the LED light assembly from impacts, dust and moisture that can cause poor illumination.
• Helps position and shield the LED so light is directed into the compartment instead of toward internal components.
• Prevents loose debris from contacting the LED or lens, reducing risk of damage or nuisance shadows.
• Fits into the existing light assembly mounting to maintain original appearance and airflow pathways.

• Always disconnect power to the appliance before starting any repair.
• Remove shelves or panels as needed for access; keep mounting screws and clips for reinstallation.
• Handle the new cover carefully to avoid scratching or cracking; align tabs and press or fasten per original mounting.
• If LEDs or wiring are exposed or damaged, replace or repair those components before reinstalling the cover.