General Electric Washer Dryer Combo Parts

This shifter spring helps engage and return the transmission shifter mechanism in select top-load washers, allowing smooth changes between agitation and spin for reliable wash performance.

• Maintains proper tension on the shift mechanism between agitate and spin
• A worn or broken spring can cause no spin, no agitate, or loud shifting noises
• May also lead to intermittent shifting or incomplete cycles
• Restores consistent mechanical engagement of the drive system

• Unplug the washer and shut off water supply before servicing
• Access is typically from the cabinet/rear; support the tub to prevent movement
• Note spring orientation and attachment points before removal
• Use needle-nose pliers or a spring tool; replace any severely worn mating parts

Washer won't start or spin? This lid lock magnet triggers the safety sensor to confirm the lid is closed. Simple DIY fix restores normal operation.

Dryer not heating or taking too long to dry? This heating element and housing assembly restores proper heat generation and airflow for even drying.

Secures the drive pulley to the motor shaft in your laundry center washer. Replace if stripped, missing, or loose to restore a solid pulley connection.

This lid actuator engages the washer's lid switch or lock when the lid closes, signaling the control that it's safe to run. Replacing a worn or broken actuator restores reliable lid detection for wash and spin cycles.

• Engages the lid switch/lock when the lid is closed
• Signals the control to allow the washer to start and spin
• A damaged or missing actuator can lead to "lid open" errors
• Common symptoms include won't start, won't spin, or lid lock light flashing

• Disconnect power before servicing
• Access the lid switch/lock area; remove the failed actuator
• Install the new actuator, aligning it to the original mounting points; reuse existing hardware
• Close up and test lid detection before running a full cycle

Note: Newly designed cover includes 4 new rod and spring assemblies. The tub dampening straps and clips are no longer used.

Replacement water fill hoses for washing machines. Connect home water supply to washer. Replace when cracked, leaking, or showing rubber wear or corrosion.

Fix a washer that won't spin or drain with this lid switch replacement. This safety switch activates when the lid closes. DIY-friendly repair.

Drain hose assembly routes wastewater from the washer pump to your standpipe or laundry tub. Replace if cracked, kinked, leaking, or causing floor puddles.

Fix a washer that won't advance through cycles or stops mid-cycle. This timer controls cycle duration and sequencing in your washer dryer combo unit.

This gas conversion kit adapts select 27-inch GE gas dryers to the correct fuel type, helping ensure safe, efficient burner performance when switching between natural gas and LP (propane) after a move or service change.

• Enables fuel-type conversion between natural gas and LP (propane), per your model's instructions
• Restores proper burner pressure and flame for safe, efficient drying
• Useful when relocating to a home with a different gas supply
• Help address weak heat, long dry times, or sooting caused by an incorrect fuel setup

• Installation must comply with local codes
• Disconnect electrical power and shut off gas supply before service
• Follow the model-specific OEM instructions exactly for adjustments and component changes
• After conversion, leak-test all connections and verify proper ignition and flame characteristics

Drive belt connects the motor to the drum for wash and spin cycles. Replace if stretched, frayed, cracked, or causing squealing noise. Verify fit.

Mounts in the washer's drive mechanism to support the shift fork. Replace if the assembly is cracked, broken, or worn to restore proper gear shifting.

Dryer barely blowing air or taking forever to dry? A worn blower wheel fails to pull air through the drum. This wheel restores airflow for efficient drying.

This CCMR 30-amp, 120-volt fuse protects the appliance's electrical circuit by opening when current exceeds safe limits. Replace a blown fuse to restore power to the affected circuit and help prevent damage to internal components.

• Provides overcurrent protection for the circuit specified by the manufacturer
• If the fuse is open, the appliance may be dead, won't start, or certain functions won't operate
• Helps prevent wiring and component damage from shorts or overloads
• Repeated fuse failures indicate an underlying electrical issue requiring diagnosis

• Disconnect power to the appliance before servicing
• Locate the fuse in its holder/block and inspect associated wiring for heat or damage
• Test the old fuse for continuity; replace only with the identical rating specified
• Never bypass or upsize a fuse; correct the root cause of the failure before returning to service

Dryer won't heat or overheats? A faulty safety thermostat fails to regulate temperature. Test for continuity with a multimeter; moderate DIY repair.