General Electric Washer Dryer Combo Parts

The Thermal Fuse is an OEM part for GE dryers. This part prevents the dryer from overheating by cutting off the power if the dryer exceeds a certain temperature. 

Causes of a bad thermal fuse can include regular wear and tear, lint build-up, restricted airflow, or a malfunctioning thermostat. 

Symptoms of a bad thermal fuse include:

• The dryer not starting
• The dryer shutting off unexpectedly during a cycle
• No heat production during drying
• The dryer running but not heating

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Mounts on the transmission shaft to transfer motor power for agitation and spin. Replace if worn, cracked, or causing belt tracking issues.

This dryer drive belt wraps around the drum and motor pulley to rotate the drum during the cycle. Replacing a worn or broken belt restores proper tumbling so clothes move freely for even drying.

• Transfers motor power to the drum to enable tumbling
• A worn, stretched, or broken belt can cause the drum not to turn
• May also result in the dryer running but not tumbling
• Visual signs include fraying, cracks, or glazing on the belt

• Unplug the dryer before servicing; allow components to cool
• Access typically requires removing the front panel and/or top panel
• Note the belt routing around the motor pulley and idler before removal
• Inspect drum rollers and idler pulley while the belt is off; replace if worn

This replacement kit combines the washer's drive motor with a protective tub shield. It restores agitation and spin performance and helps guard the new motor from splash-related moisture so your washer runs reliably through complete cycles. What it does:

• Provides the mechanical power for the washer's agitation and spin functions
• Tub shield deflects water and debris away from the motor area to reduce moisture exposure
• Helps with symptoms such as no spin or no agitation, a motor that only hums, or a burning odor from the motor area
• Useful when the original motor was damaged by leaks or corrosion

• One drive motor and one tub shield

• Disconnect power and water supply before servicing; wear gloves and eye protection
• Access the motor from the underside/front depending on the model; support the washer securely if tilting
• Move wiring connectors one at a time and transfer any brackets or pulley/belt components as configured on your unit
• Seat the tub shield properly, ensure wires are clear of moving parts, then run a test cycle to check operation and for leaks

This CCMR 30-amp, 120-volt fuse protects the appliance's electrical circuit by opening when current exceeds safe limits. Replace a blown fuse to restore power to the affected circuit and help prevent damage to internal components.

• Provides overcurrent protection for the circuit specified by the manufacturer
• If the fuse is open, the appliance may be dead, won't start, or certain functions won't operate
• Helps prevent wiring and component damage from shorts or overloads
• Repeated fuse failures indicate an underlying electrical issue requiring diagnosis

• Disconnect power to the appliance before servicing
• Locate the fuse in its holder/block and inspect associated wiring for heat or damage
• Test the old fuse for continuity; replace only with the identical rating specified
• Never bypass or upsize a fuse; correct the root cause of the failure before returning to service

Shifter hub connects the drive system to the agitator and spin mechanism in washers. Replace if cracked, worn, or broken to restore proper shifting.

Dryer not heating or leaving clothes damp? This heating element generates electric heat for proper drying. Takes under 1 hour with drum removal required.

Drum glide supports the front of your dryer drum for smooth rotation. Replace when you hear scraping or squeaking sounds. Confirm fit with your model.

Won't start, spin light blinking, or won't stop spinning? This control board manages cycles and settings. Common DIY repair, typically installed in minutes.

Internal drain hose routes wastewater through the washer drain path. Replace if cracked, kinked, or leaking to prevent water damage to floors and components.

This fuse terminal cover shields and insulates the fuse connection inside your appliance, helping prevent accidental contact and shorting. Replace a cracked or missing cover to maintain safe electrical protection and dependable circuit performance.

• Covers and insulates the fuse terminals to protect the connection
• Helps prevent accidental contact, arcing, and debris intrusion at the fuse
• Common signs you need this part: missing cover, cracks, heat discoloration, or a cover that won't stay secured
• Promotes a secure, consistent fuse connection once installed

• Disconnect power at the breaker or unplug the appliance before servicing
• Access the fuse area per your service information; note wiring and cover orientation
• Remove the damaged cover; inspect terminals and wiring for heat damage or looseness
• Seat the new cover fully and verify it is secure and clear of wiring

Washer fills but won't agitate or advance cycles? The timer controls wash, rinse, and spin sequences. DIY repair typically takes 15-30 minutes.

The Door Gasket is an OEM part for GE dryers. This seal prevents hot air from escaping during a cycle, ensuring that the dryer operates efficiently and safely. The gasket's primary role is to maintain the internal temperature and airflow, which are essential for the drying process.  

Causes of damage to the door gasket often involve regular wear and tear from opening and closing the dryer door.  

Symptoms of a bad Door Gasket include:

• Clothes taking longer to dry or not drying fully due to heat escaping from the dryer.
• An increase in energy consumption as the dryer works harder to maintain the required temperature.
• Visible wear, tears, or gaps in the gasket 
• Heat leakage from around the dryer door 

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Secures washer hoses at pump, tub, and valve connections to prevent leaks and hose blow-offs. Replace worn or missing clamps for a tight seal. Confirm fit.

Washer won't respond to cycle selections? This selector switch mounts behind the control knob to restore reliable setting changes. Easy DIY fix.

Idler arm assembly mounts to the dryer frame and maintains proper belt tension on the drum. Replace if the arm is cracked, bent, or the pulley is worn.