Hedge Trimmer Parts

Piston ring seals the gap between piston and cylinder wall in small engine equipment. Replace if worn, cracked, or causing compression loss.

This replacement carburetor kit is a genuine OEM parts kit for Craftsman hedge trimmers. The carburetor takes gasoline from the fuel line and mixes it with air from the intake valve to make a balanced fuel that is ready for combustion. Depending on how much fuel or air pass into the carburetor, the engine may run faster or slower. The most common reason for a carburetor to break down is if it is clogged with engine gunk. While it is sometimes possible to clean out a carburetor, if left for too long, the damage can be irreparable and the part will need replacing. First, remove the air filter and filter housing using a socket wrench. This will give access to the damaged carburetor and make it easier to unhook from the links that hold it in place. Be sure to set the gaskets firmly in place and then reassemble with the new part. This replacement carburetor is designed for use only with Craftsman appliances. It comes sourced directly from the original manufacturer and includes a carburetor and two gaskets.

This is a standard fuel cap for a hedge trimmer, chainsaw, or weed eater. The fuel cap assembly goes into the tank then screws onto the top of the fuel tank. A fuel cap keeps dirt and debris from falling into the fuel tank and gunking up the engine, causing it to misfire or corrode. Fuel cap assemblies are made of plastic, so they can dry out and snap. If the rubber seal on the fuel cap assembly is no longer preventing fuel from leaking, it’s time to replace it. Installing a new fuel cap assembly is simple. Just push the stopper in and screw on the lid. This is a genuine OEM product shipped from Husqvarna, the manufacturer of this part. This part is also compatible with Craftsman and Poulan products. Part sold individually.

Seals the fuel line where it passes through the chainsaw fuel tank. Replace if cracked, worn, or leaking to prevent fuel seepage and maintain proper seal.

Cleans fuel before it enters the carburetor, catching dirt and debris. Replace when clogged to restore peak engine performance and prevent starting issues.

This self-tapping screw is used to attach various parts to the engine housing of medium sized gasoline powered engines, in particular yard tools such as tillers, snow blowers, yard tractors, riding mowers, power vacuums, shredders, and chippers. It is used in over 150 different gasoline powered engines. Screws such as these are used particularly when a device is going to receive a great amount of vibration and stress while the engine is running and rotating tools are engaged. Such devices sustain a great deal of wear over time and the parts subject to replacement will eventually fail and need to be replaced. In such cases, it is wisest to replace the attaching hardware such as housing screws as well, because it is a self-tapping screw. Screws of this type are designed to forge a tight bond between the metal pieces they are securing together, but once loosened, they should ideally be replaced with new hardware. Make sure when replacing these screws to use genuine OEM parts like these screws. These replacement parts are manufactured to be identical to the original pieces. This hex screw is compatible with the following brands: MasterCut, Yard-Man, Yard Machine, Montgomery Wards, MTC, Murray, Bolens, Craftsman, Turf King, Troy Bilt, Cub Cadet, Huskee, Toro, and Ryobi.

This hex nut is designed for use with select trimmers and mowers. It is a standard hardware part that may have multiple applications depending on the type of unit and model. The nut is typically used to secure engine components or housing elements to provide safe use of the machine. These nuts are durable, but they are small and can become lost during other repairs. The constant exposure to vibrations and use can also cause them to strip or become damaged over time. Either way, a replacement with this genuine hex nut will resolve the issue and get equipment back in working order. This genuine OEM hex nut is manufactured to exact standards and sourced from the manufacturer. It can be used with trimmers and mowers from RYOBI, MTD, Bolens, Troy-Bilt, Yard Machines, Huskee, Yard Man, and Cub Cadet. Check the parts diagram for exact application and location of this nut and note that it may have multiple uses on select models. This hex nut is sold individually, and additional nuts will require the purchase of multiple pieces. In order to replace this nut, a hex socket wrench and driver will be required. Always wear gloves for safety.

Extension spring for riding mowers and lawn tractors. Replaces worn, broken, or missing springs in various linkage and control systems. Direct fit part.

Flange bearing restricts movement and prevents shifting in lawn tractor components. Replace if you notice wobbling or unusual noise. Verify fit with your model.

The bearing sleeve is an authentic part designed for use with lawn tractors of the riding variety. This bearing sleeve is located on the transmission shaft and used to assist in securing the bearing in its place. The location of this part means that it is susceptible to constant vibrations and other threats. This part can wear down over time and eventually require a replacement, or need to be replaced as a result of damage or a direct impact. Using a genuine product like this replacement bearing sleeve will provide an exact fit for compatible models. This genuine OEM bearing sleeve is manufactured to specific standards by MTD. It is compatible with tractors from MTD, RYOBI, Bolens, Yard Machines, Cub Cadet, HUSKEE, Yard Man, and Troy-Bilt. There are hundreds of tractors that can use this specific bearing sleeve. It is made of durable metal and sold as an individual unit. A wrench will be required for this part replacement, but it is an easy task that should not take a lot of time. Always disengage the engine before starting any repairs and ensure that it is not hot to avoid burns or causing potential damage.

Flat idler pulley for lawn tractors. Guides and tensions the drive belt between engine pulleys. Replace if cracked, worn, or causing belt slippage.

Few parts fulfill as many roles on lawn mowers and other landscaping power tools than the cover screw. This screw serves to attach metal housing parts, assemblies, and shrouds to one another on equipment such as power vacuums, snow blowers, edgers, tillers, hedge trimmers, lawn tractors, leaf blowers, grass trimmers and cultivators. As these are extremely durable metal screws, they seldom fail under ordinary use. It should be noted, however, that they are most often used at connection and pressure points. Stresses at these junctions sometime loosen screws, causing them to be lost or occasionally resulting in stripped threads. It's also occasionally the case that these screws are lost during repair or routine maintenance of yard equipment because of their small size. Users should make sure to consult their owner's manuals for replacement steps and any special instructions. Because of their small size and the ease of losing them during repair work or maintenance, it's recommended to keep a supply of appropriately sized screws on hand. Most importantly, when replacing a part make sure to use a genuine OEM replacement part. They are manufactured according to the specs of the original parts and are perfect replicas.

This is a genuine replacement bolt that is designed for use with select trimmers and brush cutters. The metal hex screw is generally found on the starter cover and used to secure the cover to the trimmer to protect the internal engine components. Although the screw is durable, it can become damaged due to impact or another incident. It may also be lost in the process of other repairs or maintenance. It will need to be replaced with an OEM model like this screw for the best results. This 4x16 screw is manufactured by Shindaiwa and compatible with select machines from the brand, as well as those from Little Wonder and Echo. This metal screw is sold as an individual unit and does not include any additional parts or accessories. Replacing the starter cover screw is generally a simple task. Allow the engine to cool and disconnect the power supply. Then, use an Allen wrench to remove the old screw if it isn't already missing. Install the new screw and the job will be done. It is important to wear gloves and use the right size hex key to ensure that the screw doesn't get stripped during installation.

This variable speed pulley is a genuine MTD part, sold individually. This variable speed pulley can be used as a replacement part in a lawn mower. The purpose of a variable speed pulley in a lawn mower is to regulate and manage the speed at which the motor runs so that the speed can be kept within a stable range for the safety of the operator of the appliance.The variable speed pulley in a lawn mower might have to be replaced if the variable speed pulley can no longer properly manage the speed of the lawn mower. This could occur if the variable speed pulley suffers damage from general wear and tear with long-term use or as the result of an accidental collision with a hard object that warps the variable speed pulley beyond functionality. This replacement should be executed in accordance with the proper instructions sourced from a relevant appliance manual.This component is a genuine OEM replacement part sourced directly from the manufacturer. It is sold individually. This variable speed pulley is compatible with the following outdoor appliance brands: MTD.

The ignition switch is the part of lawn and garden equipment that features an ignition to turn on and off with a switch. These are common on lawn tractors, as well as some lawn mowers, wood chippers, tillers, and log splitters. While these switches tend to be robust, they may eventually wear out. Some might have a mechanical failure after being used for years. Others might have electrical issues. Regardless of the reason for the failure, they will need to be replaced to continue using the machine. This is a genuine OEM part that is sold individually. It is a complete kit, which will include not only the switch, but also a washer and nut to secure the switch into the housing, and two ignition keys. The ignition switch can work with lawn tractors from brands such as MTD, Ryobi, Troy-Bilt, Bolens, Yard Machines, and Craftsman.