Parts for Lg LMX30995ST/01: Ice Maker & Ice Bin Parts

This is a genuine replacement screw used to secure appliance panels and components. It restores proper fastening so panels and assemblies stay aligned and operate safely. What it does:

• Fastens panels, brackets, and small assemblies to maintain structural integrity
• Replaces missing or stripped screws that cause rattling or loose parts
• Helps stop vibration-related noise when used in its original mounting locations
• Matches the OEM fit to ensure proper alignment and clearance

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or component damage
• Disconnect power to the appliance before working on electrical components
• Replace all matching fasteners for even fit

Replacement mounting bolt for refrigerator components and assemblies. Needed when original fastener is missing, stripped, or damaged during service work.

Replacement mounting screw for refrigerators. Secures internal components and panels. Order when original hardware is stripped, lost, or damaged.

Secure refrigerator panels, brackets, and internal components with this replacement mounting screw. Ideal for missing, stripped, or damaged fasteners.

Replacement mounting stud for refrigerator door handles. Installs inside the door to secure handle assembly. Needed when stud is damaged or missing.

Replacement screw for securing refrigerator panels and trim pieces. Restores proper fit when original fasteners are damaged, missing, or stripped.

Replacement mounting screw for refrigerators. Secures panels, shelves, or components inside your fridge. Order if original is stripped, missing, or lost.

This rear door handle replaces a worn or damaged handle on compatible LG appliances, restoring a secure grip and smooth opening. It's a direct-fit exterior handle that keeps the appliance door operating and looking right. What it does

• Provides a secure gripping point to open and close the appliance door
• Replaces cracked, loose, or broken rear handle hardware
• Restores correct alignment and feel when the door is operated
• Helps prevent further damage to the door edge from makeshift handles

• Power off and unplug the appliance before starting work; remove food or shelves as needed for access
• Keep fasteners and mounting clips; transfer original hardware unless new hardware is explicitly included
• Test door operation and alignment after installation; tighten fasteners evenly to avoid stress

Plastic drain tube that channels defrost water from evaporator coils to drain pan. Replace if cracked, melted, broken, or causing water leaks in freezer.

Leveling leg for refrigerators. Installs at bottom corner to elevate and stabilize the appliance. Replace if broken, compressed, or no longer secure.

Replacement mounting screw for refrigerator panels and brackets. Restores secure attachment when original fasteners are missing, stripped, or damaged.

Secures panels, brackets, and components inside your refrigerator. Replace this fastener if worn, missing, or stripped to restore proper assembly.

Multi-outlet vent duct assembly for bottom-mount refrigerators. Replaces cracked, damaged, or leaking ducts to restore proper airflow and ventilation.

Refrigerator not cooling properly? This air duct and evaporator cover with fan circulates cold air throughout your fridge. Moderate DIY repair.

Replacement ice cube tray for your refrigerator freezer. Holds water in molded cavities to form ice cubes. Replace if cracked, broken, or missing.

Drawer tray assembly for bottom-mount refrigerators. Replaces cracked, broken, or missing drawer trays. Installs in storage compartments.

Drawer tray for bottom-mount refrigerators. Replaces cracked, broken, or missing trays that support items stored in refrigerator drawers.

Replace a cracked, broken, or missing net shelf in your refrigerator door. This mesh-style storage shelf installs on the door to organize items.

Mesh shelf net for refrigerator door or interior shelves. Secures bottles, cans, and small items. Replace when torn, sagging, or missing.

Crisper glass shelf sits above crisper drawers in your refrigerator. Replace if cracked, shattered, or broken. Provides clear view and support.

Replace a cracked, broken, or missing refrigerator glass shelf. This tempered glass shelf assembly installs inside your fridge to restore storage.

Replace a cracked, broken, or missing refrigerator glass shelf. This tempered glass shelf assembly installs inside your fridge to restore storage.

Replacement tray assembly that sits in the refrigerator compartment to support and organize items. Replace if your tray is cracked, warped, or missing.

Secures and aligns refrigerator components to prevent shifting during use. Replace if bracket is cracked, broken, or missing to restore stable mounting.

Replaces a cracked or broken tray cover above a storage drawer in your refrigerator. Restores a flat, supportive surface and smooth drawer operation.

Refrigerator drawer cover panel that sits on the front of your crisper or storage drawer. Replace if cracked, broken, discolored, or missing.

Guides your refrigerator drawer for smooth, aligned movement. Replace if drawer sticks, wobbles, or makes noise. Verify fit with your model number.

Replaces worn or cracked crisper drawer inserts to keep produce organized and stable. Restores flat storage surface for easy access to fruits and vegetables.

Replacement crisper drawer for your refrigerator's produce compartment. Installs in the lower fresh food section to store fruits and vegetables securely.

Replace your cracked, broken, or missing refrigerator crisper drawer. Restores organized produce storage in the fresh food section with smooth sliding access.

Replaces the outer cabinet cover assembly on your bottom-mount refrigerator. Restores the exterior panel when cracked, warped, or missing.

This guide assembly directs and supports the vegetable crisper drawer as it slides in and out of your refrigerator. It ensures smooth operation and proper alignment while preventing the drawer from binding or falling out completely. Replace this guide if the crisper drawer is difficult to open, won't slide smoothly, or comes completely out when pulled.

Supports and guides your refrigerator's crisper bin for smooth sliding. Replace this track assembly if worn, cracked, or causing drawer misalignment.

Replace a cracked or worn drawer rail guide assembly in your refrigerator. Supports and guides pantry, crisper, or freezer drawers for smooth sliding.

Supports and guides your refrigerator drawer for smooth opening and closing. Replace if drawer sticks, misaligns, or won't seal. Confirm fit with model number.

Slide rail for fresh food tray in refrigerator. Mounts on right side to guide tray movement. Replace if cracked, warped, bent, or broken from wear.

Door hinge screws secure the refrigerator door hinges to the cabinet frame, allowing proper door operation and alignment. Replace when doors sag, don't close properly, or screws are loose, stripped, or missing causing door misalignment.

Mounting screw for refrigerator assembly. Replaces lost, stripped, or damaged screws. Essential hardware for securing panels and components.

Foam insulation assembly that installs inside the freezer door to improve energy efficiency. Replace if foam is compressed, damaged, or missing.

Foam insulation assembly that installs inside the freezer door to improve energy efficiency. Replace if foam is compressed, damaged, or missing.

Plastic cover cap for refrigerators. Snaps onto shelves, hinges, or trim to conceal screws and mounting hardware. Replace if cracked, broken, or missing.

Left-side door handle trim for refrigerators. Restores finished appearance and edge protection. Replaces cracked, scratched, or missing trim pieces.

Exterior trim piece for refrigerator door handle. Replaces cracked, scratched, or worn decorative trim to restore original appearance and finish.

Covers and protects the refrigerator door hinge assembly. Replace this cap if cracked, missing, or worn to restore a finished appearance and keep hinges clean.

Plastic cover that conceals and protects the refrigerator door hinge area. Replace if cracked, faded, or missing to restore a clean look.

This name plate is the exterior emblem that mounts to the appliance's front panel. It replaces a missing, cracked, or faded badge to restore a clean, factory look and cover the designated trim area.

• Attaches to the outer panel to display brand/series identification
• Restores a finished appearance where the original emblem sits
• Direct replacement for a lost, damaged, or worn badge
• Typical symptoms: missing emblem, loose or broken tabs, peeling, or discoloration

• Disconnect power before servicing the appliance
• Carefully remove the old emblem; release any tabs from behind or peel away remaining adhesive
• Clean and dry the mounting surface; remove all residue for best fit
• Align with the recess/holes and press evenly until fully seated

Replacement freezer door handle for bottom-mount refrigerators. Installs on freezer compartment door. Replace if broken, cracked, bent, or missing.

Replaces damaged inner door insulation foam in refrigerator doors. Restores thermal performance when original foam is crushed, deteriorated, or missing.

Molded compartment that fits into the refrigerator door to hold the home-bar area. Replace if cracked, broken, or missing to restore storage space.

Seals the Home Bar door-in-door panel to prevent warm air leaks, condensation, and temperature swings. Replace if cracked or loose. Confirm fit by model.

Seals refrigerator door to maintain temperature and energy efficiency. Replace if torn, cracked, or not sealing properly. Verify fit with model number.

Seals refrigerator door to prevent warm air entry and maintain temperature. Replace if torn, cracked, or moldy. Confirm fit with your model number.

Replaces the flap panel between French doors that seals the center gap. Order when original is cracked, broken, or won't stay closed properly.

Drawer tray assembly for bottom-mount refrigerators. Replaces cracked, broken, or missing drawer trays. Installs in storage compartments.

Front cover panel for bottom-mount refrigerators. Replaces cracked, broken, or damaged exterior covers. Restores appearance and protects components.

Replacement door basket for refrigerator doors. Restores storage space for bottles and small items. Replaces cracked, broken, or missing door bins.

This door basket is the inner door panel that holds items and protects internal components, restoring proper loading and access. It replaces a cracked, dented, or broken basket to help secure contents and improve door closure. What it does:

• Provides a rigid storage surface on the appliance door and protects internal mechanisms.
• Stops items from falling out when the door opens; prevents rattling and extra movement.
• Restores proper alignment and secure closure when the original basket is damaged or cracked.
• Helps maintain a clean interior by covering internal cavities and trim.

• Disconnect power to the appliance before beginning any service.
• Remove any items from the door and support the door while detaching the old basket.
• Line up mounting tabs and fasteners; press or secure the basket until it snaps into place.
• Inspect seals and hinges after installation; test door operation before regular use.

Storage bin that installs inside your refrigerator door for convenient access to frequently used items. Replace if cracked, broken, or missing.

Refrigerator door basket mounts on the inner door liner to hold bottles and condiments. Replace if cracked, broken, or missing to restore storage.

Replacement door bin for refrigerators. Mounts inside the door to hold bottles, jars, and condiments. Replace if cracked, broken, or missing.

Refrigerator door shelf bin installs on the refrigerator door for storing condiments and beverages. Replace if cracked, broken, or damaged.

Secures and supports the bottom door pivot point. Replace when doors sag, rub, or fail to seal evenly. Restores proper alignment and smooth operation.

Stabilizes rotating assemblies in your refrigerator to reduce wobble, wear, and noise. Replace when you notice excessive movement or grinding sounds.

Mounts at the hinge to control door opening range and promote smooth closing. Replace if cracked, broken, or worn to restore proper door swing.

Mounts at the hinge to limit your refrigerator door's opening angle. Replace if cracked, broken, or missing to prevent over-swing and protect the hinge.

Hinge assembly for refrigerator doors. Installs at door pivot point to support door weight and enable smooth opening/closing. Replace if cracked or worn.

Replace your cracked, scratched, or discolored refrigerator door handle. Installs on fresh food or freezer doors for a secure grip and updated look.

Replace a cracked, broken, or damaged refrigerator door handle. Installs on the refrigerator door to provide a secure grip for opening and closing.

Connector assembly for bottom-mount refrigerators. Replaces broken, cracked, or missing connectors that join internal components or panels.

Connector assembly for bottom-mount refrigerators. Replaces broken, cracked, or missing connectors that join internal components or panels.

Plastic rail holder that secures refrigerator shelf rails in place. Replace if cracked, broken, or missing to properly support shelves and prevent sagging.

Drawer rail guide assembly for bottom-mount refrigerators. Mounts to the drawer track system to ensure smooth gliding. Replace if cracked or worn.

Mounting bracket that secures refrigerator rails in place. Replace if your holder is cracked, broken, or missing to restore stable rail support.

This slide rail is the replacement drawer track that lets a refrigerator or freezer drawer glide smoothly and stay aligned. It restores proper drawer movement for easier access and prevents sticking or uneven operation. What it does:

• Guides the refrigerator/freezer drawer along its intended path for smooth opening and closing
• Keeps the drawer aligned to prevent binding, jamming, or uneven movement
• Supports the drawer weight so it operates securely and consistently
• Helps restore normal access when worn or damaged tracks cause sticking or misalignment

• One slide rail

• Remove power and empty the drawer before attempting repair to avoid injury or damage
• Use basic hand tools; do not force components—inspect mating hardware for wear
• If screws or clips are missing or damaged, replace them with OEM equivalents

This ice maker drive gear replaces the small plastic gear that turns the ice-eject/auger mechanism so your ice maker can harvest and dispense cubes reliably. Fits compatible LG ice maker assemblies. What it does

• Transfers motor rotation to the ice-eject/auger mechanism so ice cubes are pushed out or advanced.
• Commonly replaced when cubes aren't being ejected, ice builds up, or the mechanism spins without moving the ejector.
• Works with the ice maker's actuator/motor to synchronize harvest and fill cycles.
• Small, precision-molded gear designed for quiet, consistent operation in the ice maker assembly.

• One ice maker drive gear.

• Disconnect power to the appliance before servicing to avoid shock or accidental motor operation.
• Remove the ice maker module and inspect surrounding gears/shaft for wear or debris before installing.
• Press the gear onto the motor shaft or replace the internal gear assembly as required; do not force or hammer into place.
• If other components show wear (motor, shaft, or companion gears), replace them to prevent repeat failure.

Handle bar for bottom-mount refrigerators. Replaces damaged, cracked, or broken handle bars on door assemblies. Direct fit replacement part.

Refrigerator handle bar component for bottom-mount models. Installs on the door to provide grip. Replace if cracked, broken, or missing.

Replace a cracked, broken, or missing handle bar on your bottom-mount refrigerator. This structural component installs on the door for grip and access.

Secures and aligns refrigerator doors for smooth operation. Replace if doors sag, misalign, or don't seal properly. Confirm fit with your model number.

Center hinge assembly supports and pivots your refrigerator door at mid-point. Replace when door sags or won't close flush. Verify fit by model number.

Secures components inside your refrigerator. Replace if broken or missing to prevent rattling and ensure proper part alignment. Confirm fit with model.

The Spanner Wrench is an OEM replacement part for LG refrigerators. This tool allows you to adjust the door hinges to ensure the doors are level and aligned properly. A well-aligned door is crucial for maintaining the internal temperature and efficiency of the refrigerator, preventing energy loss and ensuring food is stored under optimal conditions.

Symptoms that you might need to adjust the door hinges and potentially need this wrench include:

• Doors not closing properly or sealing tightly
• Visible gaps between the door and the main body of the refrigerator
• The refrigerator tilting or not sitting level

This spanner wrench is also compatible with some Sears/Kenmore refrigerators. 

Replaces the top door pivot to restore proper alignment and smooth opening. Install when your refrigerator door sags or seals unevenly. Confirm fit with model.

Secures and guides your refrigerator door for smooth opening and closing. Replace if door sags, rubs, or won't seal properly. Confirm fit by model number.

Upper hinge assembly supports your refrigerator door and ensures smooth opening. Replace when door sags or gaps appear. Verify fit with your model number.

Ice freezing in chute or water dripping from dispenser? This ice dispenser door assembly restores proper sealing. 15-minute DIY repair with video guide.

This lever holder is the replacement mounting bracket that secures the door lever so the microwave door operates smoothly and reliably. It restores proper lever alignment to help the door latch and release as intended. What it does:

• Secures the door lever assembly so the door can latch and release properly
• Keeps the lever aligned to prevent binding, sticking, or loose movement
• Helps restore normal door operation and user access to the oven cavity
• Common symptom: door feels loose, lever moves freely, or door will not latch

• Disconnect power before beginning any repair to avoid shock or injury
• Remove the outer cabinet or door trim only as needed to access the lever area
• Handle door components and glass carefully to avoid damage or injury

Restores tension to your refrigerator door hinge for smooth operation. Replace this spring if your door sags, won't hold position, or shows wear.

This holder bracket secures internal refrigerator components in place. Replace if your original bracket is cracked, broken, or missing to restore stability.

Ice dispenser door spring maintains tension for smooth opening and closing of the ice compartment door. Replace if door won't seal or spring shows wear.

Secures the dispenser lever in place on your refrigerator. Replace if retainer is cracked, broken, or missing to restore proper lever stability.

Spring that tensions the ice dispenser door for proper closing and airtight seal. Replace if door won't close or ice gets stuck. Verify fit with model.

Fix dispenser drips and spills with this refrigerator dispenser funnel. Guides water flow cleanly to prevent messes. Simple 5-minute installation.

Ice stuck in dispenser door or won't dispense? This ice dispenser door lever controls ice release. DIY repair in under 15 minutes with video guide.

The Cover, Display is an OEM component specifically designed for LG refrigerators. This part protects and houses the display panel that provides important appliance information and allows for cycle/setting selections. 

The display cover is responsible for safeguarding the sensitive electronic display from damage and wear. It provides an aesthetically pleasing outer surface that seamlessly blends into the refrigerator exterior. 

Causes of a bad cover can include cracks, scratches, discoloration from repeated cleaning, or loose/missing mounting brackets over time. 

Symptoms of a bad cover include:

• Exposure of the display components to moisture or impact damage
• Display malfunctions or errors due to inadequate protection
• An unattractive or incomplete appearance

This OEM LG part is also compatible with Sears/Kenmore. Replacing it will preserve your refrigerator's display and upgrade its look.

Internal bracket assembly that mounts and secures the door handle to your refrigerator door. Replace if the bracket is cracked, broken, or stripped threads.

Covers and protects the dispenser area on your refrigerator. Replace if cracked, broken, or scratched from repeated use and moisture exposure.

Ice won't dispense or keeps flowing? This ice dispenser button replaces broken levers causing continuous dispensing. DIY-friendly repair in 30-45 minutes.

Replaces a broken, cracked, or missing water dispenser button on your refrigerator. This snap-on part installs on the dispenser housing panel.

Refrigerator door handle assembly for models with decorative exterior finish. Replace if handle is cracked, broken, or buttons have fallen off.

Rubber cap for bottom-mount refrigerators. Installs on various internal components. Replace if cracked, worn, missing, or damaged to restore appearance.

Water pooling under your dispenser? This drip tray catches overflow and spills. Cracked or stained trays are easy to replace with basic tools.

Refrigerator not cooling or freezer warm? The compressor assembly circulates refrigerant to maintain temperature. Professional installation recommended.

Fix a refrigerator not cooling properly with this evaporator coil assembly. Restores proper cooling when frost buildup or coil damage occurs.

Fix refrigerator not cooling or freezing issues with this evaporator assembly. Essential component for proper temperature control in bottom-mount models.

The Thermistor Assembly is an OEM part for LG refrigerators. It serves a crucial function in monitoring and regulating the temperature within the appliance. By sensing temperature changes, the thermistor sends information to the refrigerator’s control board, ensuring the system adjusts cooling to maintain the desired temperature settings. 

Symptoms of a failing thermistor assembly include:

• Inconsistent temperatures in the refrigerator or freezer
• Refrigerator running longer than usual or not cooling efficiently
• Frequent fluctuations in temperature readings

Causes of thermistor assembly failure typically involve electrical faults, damage from moisture or frost, or simple wear over time, which can impact its ability to accurately measure and report temperatures.

This OEM LG part is also compatible with Sears/Kenmore.

Refrigerator stopped cooling after power outage? The compressor overload protector prevents overheating damage. Easy DIY fix when compressor won't run.

This PTC cover is the protective housing that shields a PTC sensor/assembly from debris and physical damage, helping maintain reliable sensor performance and prolong component life in the appliance. What it does:

• Protects the PTC sensor or PTC assembly from dust, impact, and accidental contact
• Helps prevent shorting or intermittent sensor signals caused by contaminants
• Supports proper positioning and mounting of the PTC component
• Can help address symptoms such as visible sensor damage, exposed wiring, or intermittent operation related to a compromised sensor housing

• Disconnect power to the appliance before starting any repair
• Remove the outer panel(s) as needed to access the PTC location; handle surrounding wiring and components carefully
• Replace only with the correct OEM cover to ensure proper fit and protection

Rattling or loose parts in your refrigerator? This retaining pin secures moving components and keeps them aligned for smooth, quiet operation.

Support roller that mounts to the refrigerator base, allowing the unit to roll for cleaning or service. Replace if worn, broken, or causing uneven positioning.

Vibration-isolating grommet that mounts between the compressor and chassis. Replace if cracked, worn, or missing to restore proper cushioning.

Water pooling inside your refrigerator? This drip tray collects condensate and defrost water to prevent leaks. Direct-fit replacement part.

Fixes uneven cooling and scraping noises by directing airflow from the fan. This guide restores proper air circulation throughout your refrigerator.

Fix a refrigerator not cooling properly with this compressor sealing pipe. Essential sealed system component for restoring proper refrigeration.

Cosmetic cover panel for refrigerator home bar compartment. Replaces cracked, broken, or missing covers that affect appearance and door aesthetics.

Drain tray assembly for bottom-mount refrigerators. Collects defrost water beneath the unit. Replace if cracked, broken, or leaking onto the floor.

Water pooling under your refrigerator? This drain tray assembly collects condensate and directs it properly to prevent leaks and water damage.

Front cover assembly for bottom-mount refrigerators. Replaces cracked, broken, or damaged exterior cover panels. Essential for restoring appearance.

Refrigerator making unusual grinding noises or exposed machinery? This machinery cover assembly shields internal components from debris and damage.

This is a small retainer clip that secures the compressor in place at the base of the refrigerator. It helps prevent the compressor from shifting or vibrating excessively during operation. Replace this clip if your refrigerator produces unusual rattling or vibrating noises from the back, or if the compressor appears loose or has shifted from its mounting position.

Drier assembly for refrigerators. Installs in the sealed refrigerant system to remove moisture and contaminants. Replace if damaged or worn during repair.

This holder is a small mounting bracket used to secure internal components in place, helping keep parts aligned and stable for reliable operation. It provides a direct, OEM-compatible replacement to restore proper fit and function. What it does

• Secures and supports nearby components to prevent shifting or vibration.
• Restores proper alignment where a worn or broken holder causes rattling or loose parts.
• Helps maintain normal operation by keeping assemblies seated correctly.
• Works behind panels or inside assemblies where a dedicated bracket is required.

• One holder/mounting bracket as shown.

• Installation generally requires removing the panel or access cover where the holder is located.
• Use proper fasteners shown in your appliance; replace any damaged screws or clips as needed.
• Disconnect power before servicing electrical appliances to reduce shock risk.

Fix uneven cooling or frozen food in fresh food section with this refrigerator air damper. Controls airflow between compartments to balance temperatures.

The Fan Assembly is an OEM part for LG refrigerators. It is responsible for circulating air within the refrigerator and freezer compartments, ensuring consistent cooling and optimal temperature distribution. The fan assembly helps maintain the freshness of your food by evenly distributing cold air.

Common causes of a bad fan assembly include electrical issues, worn-out bearings, or obstructions that prevent the fan from spinning properly.

Symptoms of a bad fan assembly include:

• Unusual noises coming from the refrigerator
• Inconsistent temperatures within the fridge or freezer
• Frost buildup in the freezer
• Refrigerator running continuously or not cooling effectively

This OEM LG part is also compatible with Sears/Kenmore models.

Freezer frosting over or refrigerator not cooling? This defrost control assembly regulates the defrost cycle to prevent ice buildup. Moderate DIY repair.

This is a temperature sensor assembly that monitors the internal temperature of the refrigerator compartment and relays readings to the control board. It helps regulate cooling cycles and defrost timing to maintain proper temperatures. Replace this sensor if your refrigerator is running too cold, too warm, not defrosting properly, or displaying error codes related to temperature.

If your refrigerator light stays on or interior won't cool properly, the door switch may have failed. This magnetic switch detects door position.

Refrigerator light won't turn off when door closes? This door switch controls interior lighting based on door position. Simple DIY repair.

Fix a dispenser that won't stop running or fails to dispense ice or water. This switch activates your dispenser when pressed. DIY-friendly repair.

Fix a stuck or non-working ice/water dispenser with this micro switch. Common cause of dispensers running continuously or not activating. Easy DIY repair.

Refrigerator not cooling or running warm? A faulty condenser fan motor assembly prevents proper airflow across the condenser. Includes motor and blade.

If your refrigerator shows an ER RF error code or won't cool properly, this fan motor assembly restores airflow. Moderate DIY difficulty repair.