Ikea Refrigerator Parts

Connects the water valve to the filter and dispenser in your refrigerator. Replace if cracked, leaking, or damaged. Installs behind ceiling panel.

Ice maker not cycling or shutting off? This control arm extension restores proper movement to the ice maker mechanism. Simple snap-in replacement.

This factory screw secures panels, brackets, and other components in your cooking appliance. Replace a missing, stripped, or corroded fastener to restore a tight, rattle-free fit and keep parts properly aligned during use.

• Fastens components to maintain proper alignment and stability
• Helps prevent vibration, rattling, and loose parts during operation
• Replace if threads are stripped, the head is damaged, or the screw is missing
• Commonly used to mount internal or exterior parts in ranges and wall ovens

• Disconnect power and allow the appliance to cool; shut off gas supply if applicable
• Use the correct driver bit to avoid stripping the screw head
• Install in the original location and do not overtighten
• If the receiving threads are damaged, repair or replace the mating part before installation

The shut-off arm is the lever that tells the ice maker when to stop and start making ice. Replace a bent, missing, or jammed arm to restore proper ice production control and prevent bin overfilling. What it does:

• Lowers to allow ice production; raises to stop cycles when the bin is full (down = on, up = off)
• Helps prevent overfilling, spills, and auger jams
• Common symptoms: ice maker won't stop making ice, no ice when the arm is stuck up, inconsistent ice production from misalignment
• Restores proper ice level sensing when the original lever is damaged or missing

• One shut-off arm

• Disconnect power and shut off water before servicing
• Remove the ice bin to access the ice maker
• Seat the arm's pivot ends fully in the ice maker head; avoid bending the lever
• The arm moves freely up/down and clears the bin before restoring power

Gray door hinge for side-by-side refrigerators. Replaces cracked, broken, or worn hinges that cause misalignment or sagging doors.

Door hinge butt for top-mount refrigerators. Mounts between cabinet and door to support hinge pin assembly. Replace if cracked, broken, or worn out.

Interior light won't turn on when door opens? This push-button door switch restores automatic lighting. Moderate DIY repair with basic tools.

Black toe grille panel for bottom-mount refrigerators. Covers the base opening and leveling feet. Replace if cracked, broken, or clips are damaged.

Channels defrost water from the drain outlet to the pan. Replace if cracked, disconnected, or clogged to prevent water pooling inside or leaking onto floor.

This is the fan blade that attaches to the condenser fan motor, typically located near the bottom rear of the refrigerator. It draws air across the condenser coils to dissipate heat and keep the refrigerator running efficiently. Replace this blade if it is cracked, warped, or broken, which can cause loud noises, reduced cooling performance, or the compressor overheating.

Covers and protects your refrigerator's light source. Replace if cracked, yellowed, or missing to restore clear illumination. Confirm fit by model number.

Left-hand gray upper hinge cover snaps over the top door hinge to conceal hardware and restore a finished look. Replace when cracked, broken, or missing.

Collects defrost water from the evaporator and directs it to the drain. Replace if cracked, broken, or leaking to prevent water pooling under your fridge.

Drip tray collects defrost and condensation water beneath your refrigerator. Replaces cracked, broken, or missing trays to prevent leaks and floor damage.

This ice deflector guides ice cubes from the icemaker into the ice bin to help keep ice delivery consistent and reduce cube jams or spills. It's a simple replacement that restores proper ice routing in compatible refrigerators. What it does:

• Directs ice cubes from the icemaker into the ice bin for orderly dispensing
• Helps prevent ice clumping and blockages that can stop ice flow
• Keeps ice moving away from the icemaker assembly and into the bin
• Restores proper alignment and function after a cracked or missing deflector

• Disconnect power to the refrigerator before servicing to avoid electrical or mechanical injury
• Remove the ice bin or access panel per your model's service instructions to reach the deflector
• Part typically snaps or slides into place; reuse existing fasteners unless new hardware is supplied
• After installation, reconnect power and run the icemaker through a cycle; discard any ice made during the repair if contamination is suspected

Shields and positions the temperature sensor for accurate readings. Replace if cracked, broken, or missing to restore proper sensor placement and airflow.