Ikea Refrigerator Parts

Color: Grey

This refrigerator drain tube channels defrost water from the evaporator to the rear drain pan so it can evaporate. Replace a cracked, missing, or clogged tube to stop interior leaks and ice buildup.

• Routes defrost meltwater from the freezer drain to the condenser drip pan
• Helps prevent pooling under crisper drawers or water on the floor
• Common failure symptoms: water under drawers, ice sheet in the freezer bottom, recurring drain clogs or freeze-ups, dripping at the rear base
• Restores proper drainage when the original tube is brittle, split, or obstructed

• Disconnect power; pull the unit forward and remove the lower rear access panel
• Remove the old tube from the drain outlet and drip pan; clear any ice/debris with warm water—avoid sharp tools
• Seat the new tube fully on the drain outlet and position the outlet into the pan; verify flow by pouring warm water down the drain
• Restore power and monitor for leaks as normal defrost cycles resume

This door-activated light switch installs in the refrigerator liner and opens or closes the circuit to the interior lamp as the door moves. It restores reliable, automatic on/off lighting when you open and close the door. What it does:

• Controls the interior light based on door position
• Helps fix a light that won't turn on with the door open
• Helps fix a light that stays on when the door is closed
• On some models, also signals door-ajar/dispenser interlock functions

• 1 light/lamp switch

• Disconnect power to the refrigerator before servicing
• The switch is typically in the door jamb; gently release and pull it out, then transfer wires one at a time to the new switch
• Match wire positions/orientation and seat the switch flush to prevent air leaks
• Test door operation and light before finalizing reassembly

The Glide is an OEM part for Frigidaire ranges. It ensures smooth movement of the storage drawer, allowing you to easily access and organize your stored items.

A bad glide can be caused by wear and tear, damage, or lack of lubrication. Signs of a faulty glide include a sticky or jammed drawer, uneven sliding, or a drawer that doesn't close properly.

Symptoms of a bad glide can include:

• Difficulty in opening or closing the storage drawer.
• Uneven or jerky sliding motion of the drawer.
• Drawer getting stuck or not fully closing.

Replace your worn-out or damaged glide with this genuine OEM part to restore movement to your range's storage drawer. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

A replacement hinge pin that secures and guides the appliance door hinge so the door opens, closes and stays aligned. Installs quickly to restore correct door pivot and reduce sag or binding. What it does

• Acts as the pivot point for the door hinge so the door swings smoothly.
• Restores proper door alignment to prevent gaps or doors that won't latch fully.
• Stops noisy or rough door movement caused by a worn or bent pin.
• Helps maintain seal performance by keeping the door flush with the cabinet.

• Disconnect power to the appliance and remove any items from the door area before starting.
• Support the door while removing/installing the pin to avoid damage or injury.
• Use appropriate hand tools and keep track of any retainers or fasteners removed.

This handle plug snaps into the handle opening to cover the exposed mounting hole and restore a clean, finished look. Replacing a missing or damaged plug also helps keep debris out of the handle cavity.

• Covers the handle's exposed screw/mounting hole for a finished appearance
• Snaps in for a secure, flush fit
• Helps keep dust and moisture out of the handle opening
• Common symptoms: missing plug, cracked or loose cap, visible hole in the handle

• Disconnect power if working near electrical components and allow any hot surfaces to cool
• Protect the finish; use a plastic pry tool to remove the old plug
• Align the new plug with the opening and press firmly until it seats flush
• Replace additional plugs as needed for a uniform look

This top hinge assembly fits the right-hand refrigerator door. Replacing a worn or damaged hinge restores smooth door movement and correct alignment so the door closes securely and the gasket seals to maintain proper temperature. What it does:

• Supports and pivots the door at the top
• Keeps the door aligned for even gaps and reliable gasket contact
• Replaces a bent, loose, or broken hinge to stop door sagging or rubbing
• Common symptoms include popping/clicking at the top, poor closing, or uneven spacing

• One right-hand top hinge assembly

• Disconnect power before servicing
• Have a second person support the door while removing the hinge
• Remove the top hinge cover and screws, lift the door off, install the new hinge, and reinstall screws
• Rehang and align the door; confirm the gasket seals evenly before restoring power

This hinge cover assembly conceals and protects the door hinge area, providing a clean look while shielding wiring and moving parts from dust and moisture. It restores proper coverage if the original cover is cracked, missing, or loose.

• Covers the hinge area to protect components and improve appearance
• Helps prevent debris intrusion around the hinge mechanism
• Common fix for a broken, missing, or damaged hinge cover
• May help if the hinge area is exposed or rattling due to a loose cover

• Unplug appliance before service; shut off water if applicable
• Use a non-marring tool to release clips or tabs; avoid prying on finished surfaces
• Transfer any reusable screws or trim from the old cover
• Confirm secure engagement of tabs/screws to prevent vibration

This thermistor cover shields and positions the refrigerator's temperature sensor so it reads cabinet air accurately. Replacing a cracked or missing cover helps restore stable temperatures and normal cooling performance.

• Holds the thermistor in place and shields it from direct airflow for accurate temperature sensing
• Helps prevent erratic temperatures, overcooling/undercooling, or long run times caused by an exposed sensor
• Commonly replaced when the original cover is cracked, loose, or missing
• Supports consistent temperature control by ensuring proper sensor placement

• Disconnect power before servicing
• Remove shelves/bins as needed to access the sensor location
• Align the thermistor and seat the cover fully; engage tabs or reuse existing hardware per model
• Avoid pinching the sensor or wiring and verify the cover is snug

This upper hinge cover fits the left-hand side and snaps over the top door hinge in a gray finish. It protects the hinge hardware and restores a clean, finished look when the original cover is cracked or missing.

• Conceals upper hinge hardware on the left side for a clean appearance
• Shields the hinge area from dust and minor spills
• Helps prevent snagging or damage to wires routed through the hinge area on some models
• Typical symptoms: broken, loose, or missing hinge cover

• Disconnect power to the appliance before servicing
• Remove any retaining screw(s) or release tabs from the old cover; keep original fasteners for reuse
• Align the new cover over the hinge and snap or secure into place
• Support the door before loosening fasteners

Color: Black. Instruction sheet included.

This cover replaces a cracked, warped, or missing cover on your appliance. It protects internal components and restores the correct fit and finish so parts stay secured and the unit operates as designed.

• Shields internal components from debris and moisture
• Helps maintain proper airflow, water path, or guarding as designed
• Restores fit/finish and keeps parts secured
• Common signs of failure: cracks, broken tabs, discoloration, or a cover that won't stay in place

• Disconnect power and shut off water/gas before servicing
• Note the original orientation and transfer any screws/clips from the old part
• Align tabs and fasteners; avoid overtightening to prevent damage
• After installation, test operation and ensure no interference or leaks

This fill tube heater keeps the ice maker's water inlet from freezing so your refrigerator can produce ice reliably. It applies gentle heat around the fill tube to help prevent ice blockages and water drips in the freezer.

• Warms the ice maker fill tube to help prevent freezing and ice buildup
• Helps maintain consistent water flow into the ice maker during fill
• Can address symptoms like no ice production, small/hollow cubes, or a frozen fill tube
• Reduces leaks at the fill spout caused by ice blockage

• Unplug the refrigerator and turn off the water supply before servicing.
• Defrost any ice in the fill tube area; avoid sharp tools that can puncture plastic.
• Route and secure the heater along the fill tube as originally installed; avoid pinching wires.
• Ensure the electrical connector is fully seated, then restore power and verify ice maker operation.

The Drawer Glide Gear is an OEM replacement part for Frigidaire refrigerators. It is a metal component located on each side of wire shelf tracks that work together to make shelf and drawer movements smooth. 

Causes of bad glide gears can include wear from years of extended usage, dents or deformation that restrict proper motion, or failure of lubricating parts inside the gear mechanism.

Symptoms of a bad Drawer Glide Gear include:

• Shelves or drawers that stick or fail to slide freely
• Noisy squeaking or grinding noises coming from shelf areas  
• Shelves difficult to properly align or position as needed

As a high-stress moving part, glide gears can degrade and lead to slothful storage access over time. Replace with this genuine OEM component for optimally smooth shelf performance on your Frigidaire refrigerator. The replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This chute channels water and wash additives from the dispenser housing into the tub. Replacing a damaged or clogged chute helps ensure proper dispensing and reduces leaks or residue around the dispenser area. What it does:

• Guides detergent/bleach/fabric softener from the dispenser to the wash tub
• Maintains proper flow to prevent backups at the dispenser drawer
• Helps reduce leaks and drips from the dispenser area
• Common failure symptoms include water backing up into the drawer, detergent residue left in the dispenser, or leaks at the front-left/top of the washer

• 1 chute

• Disconnect power and turn off water supply before servicing
• Access is typically from the top; remove panels as needed to reach the dispenser assembly
• Transfer any seals, clamps, or hardware from the old chute
• Reassemble and run a brief fill/rinse to check for proper flow and leaks

This dispenser drip tray sits beneath the ice/water dispenser recess to catch small drips and spills. Replacing a cracked or missing tray helps protect the door and floor while keeping the dispenser area neat and easier to clean. What it does:

• Collects water and beverage drips from the dispenser area
• Helps prevent moisture from running down the door or onto the floor
• Restores a clean, finished look if the original is cracked, warped, stained, or missing
• Improves fit if the old tray no longer sits securely

• One dispenser drip tray

• Unplug the refrigerator and turn off the water supply before servicing
• Lift the old tray straight out; clean the recess of debris and residue
• Align and press the new tray in until it sits flush and secure
• Do not force or pry against surrounding trim to avoid damage