Jenn-Air Wire, Harness, Power Cord

This wire harness connects the ice maker's cutter grid to the appliance's electrical system, supplying power so the heated grid can slice the ice slab into cubes. Replacing a damaged harness helps restore consistent cube separation and production.

• Routes electrical power to the cutter grid/heating wires
• A failed, loose, or heat-damaged harness may prevent the grid from warming
• Common symptoms may include whole sheets or large chunks in the bin, cubes not separating, or intermittent/slow ice production
• Visual signs can include melted/discolored grid connectors or broken/brittle conductors

• Disconnect power before servicing; allow the cutter grid to cool completely
• Note wiring/connector orientation; transfer one connection at a time to match original routing
• Seat connectors fully and secure the harness in original clips/standoffs away from sharp edges
• After reassembly, restore power and verify the cutter grid warms during a cycle

This wire harness routes power and signals between appliance controls and electrical components to restore reliable operation. Replaces a damaged, frayed, or burnt harness to help eliminate intermittent or lost power to components. What it does:

• Carries electrical power and control signals between the control board and motors, switches, sensors, or heating elements
• Restores consistent electrical connections when original wiring is damaged, corroded, or pinched
• Addresses symptoms such as components not powering on, intermittent operation, blown fuses, or visible burn/damage at wiring
• Prevents shorting and arcing caused by exposed or broken conductors when replaced promptly

• One wire harness as pictured and specified by the manufacturer

• Disconnect power at the breaker or unplug the appliance before inspecting or replacing the harness
• Match connector shapes and pin counts; route harness clear of sharp edges, heat sources, and moving parts
• Use only the exact replacement harness to maintain proper connector fit and circuit protection
• If you see burned connectors, melted insulation, or a repeatedly tripped breaker, inspect related components and replace damaged parts as needed

This wire harness is the factory-style wiring assembly that routes power and signals between components, restoring reliable electrical connections for safe appliance operation. Replace a damaged or burned harness to reestablish proper power and control function. What it does:

• Carries power and control signals between controls, motors, switches, and sensors
• Restores lost or intermittent power caused by frayed, broken, or burned wires
• Prevents shorts and arcing from damaged insulation or loose connectors
• Ensures correct connector routing for dependable component operation

• Disconnect power (unplug or shut off breaker) before starting any repair
• Compare new harness to the old part for connector type, length, and routing before installation
• Route wires along the original paths and secure all clips and fasteners to avoid rubbing or heat contact

This main wiring harness routes power and control signals between the appliance's control assembly and internal components so the unit can operate reliably. It restores electrical connectivity when the original harness is damaged or has failed connections. What it does:

• Provides organized wiring paths for power and signal connections between the control board, user interface, motors, valves, and sensors
• Replaces damaged, frayed, or burned wiring that can cause intermittent operation or complete loss of function
• Helps resolve symptoms such as unresponsive controls, no power to components, or erratic behavior caused by loose or broken wires
• Maintains correct connector pin assignments to ensure each component receives the proper signals

• Disconnect power to the appliance before starting any repair to avoid shock or damage.
• Compare connectors and wire colors to the existing harness to ensure correct replacement and routing.
• Route and secure the harness to prevent chafing or pinch points; avoid sharp bends.

This wire harness connects key components so your appliance controls and sensors communicate reliably. Replaces a damaged or frayed harness to restore normal electrical connections and help resolve intermittent power or control issues. What it does:

• Routes power and signal connections between the control board, switches, and sensors
• Restores missing or intermittent electrical continuity caused by broken or burned wires
• Helps stop erratic operation, control failures, or no-power conditions linked to damaged wiring
• Matches OEM connector and terminal locations for a direct replacement

• Disconnect power at the breaker or unplug the appliance before starting any work
• Handle connectors gently; match keyed plugs and secure all wire routing away from moving parts and sharp edges
• If terminals are corroded or connectors are damaged, replace connectors