Need Help?
Call
Bypass cap allows your refrigerator to dispense water without a filter installed. Replace when using external filtration or RO systems. Confirm fit with your model.
Replaced water reservoir and water valve assembly. This corrected both problems. Before attempting this repair I used the Appliance Parts Forum for info on how to make these repairs. I had no idea where the valve and reservoir were located before I started. It became a very easy repair thanks to AppliancePartsPro.com. Read more
This is a cover assembly that fits over the water dispenser area on the front of the refrigerator. It protects the internal dispenser components and provides a finished appearance on the exterior of the door. Replace this cover if it is cracked, broken, discolored, or if it no longer snaps securely into place.
There was a little tiny black part inside of where the water comes out. I took a photo of that part, then I studied the tech specs for the make and model of my fridge for almost 2 hours until I found a part that looked very similar to my photo of the little black part. It was a limit switch. Sure enough, that was it!!! Water now dispenses, and even better, when you pull the glass away, the water stops coming out! Read more
This is a small white plastic plug that fills the hinge sleeve hole on a refrigerator or freezer door. It covers unused hinge mounting holes to provide a clean, finished appearance, especially after reversing the door swing. Replace this plug if it has cracked, fallen out, or gone missing, leaving an exposed hole in the door.
Took off the freezer door, took off the top hinge on the refrigerator door, replaced the handle, re-installed the top hinge and the freezer door. This is a two person job - one to remove the top hinge and replace the handle, while a second person holds the refrigerator door in place. Replacing the handle was easy. The most irritating part was figuring out what parts to order. The drawing of the refrigerator door (Drawing # 4) used to figure out what parts to order was not clear. I paid $8... Read more
Front cover panel for your refrigerator door. Snaps into place to restore appearance and protect controls. Replace if cracked, broken, or missing clips.
I opened the front cover (breaking the spear that holds it in place on the right hand side), easily removed the defective reservoir and replaced it with the new one. I also replaced the front cover with a new cover to make up for the broken spear. Took less than 10 minutes. Read more
Covers the detergent dispenser drawer opening on your washer. Replace this plastic cover if it's cracked, broken, or missing to restore a clean appearance.
Plastic cap that snaps over refrigerator door handle ends to cover mounting screws and finish the handle. Replaces lost, cracked, or broken caps.
I ordered replacement plugs. The order went smoothly and expeditiously Read more
This cover mounts inside the dryer and shields the drum light from direct contact with tumbling clothes. It helps protect the light bulb and prevents garments from snagging on the light assembly. Replace this cover if it is cracked, melted, missing, or if clothes are catching near the light area during drying cycles.
Repair was quick remove the hold down screw and repace. Read more
Bypass cap replaces water filter when using external filtration or no filter needed. Allows ice maker and water dispenser to function normally.
This website was very informative, has videos with detailed instructions. The shipping is fast and was a good experience. I will be referring them to others and keeping it bookmarked in case I need it again. Read more
Molded housing that shields the infrared emitter in your refrigerator's ice level optics system. Replace if cracked, broken, or missing to protect the board.
Your video was perfect without it I would of never been able to repair my ice maker Read more
Left-hand gray upper hinge cover snaps over the top door hinge to conceal hardware and restore a finished look. Replace when cracked, broken, or missing.
Shield cap for laundry center washers. Covers and protects internal components. Replace if cracked, broken, or missing to maintain proper enclosure.
Shields and positions the temperature sensor for accurate readings. Replace if cracked, broken, or missing to restore proper sensor placement and airflow.
Covers the factory test opening on your refrigerator cabinet or liner. Replace if missing, cracked, or damaged to restore a finished look and seal.
Protective cover that snaps over your freezer's door hinge. Replace if cracked, broken, or missing to restore a finished look and shield the hinge.
Molded trim piece that shields and supports the washer guide track assembly. Replace if cracked, broken, or missing to maintain smooth alignment.
Freezer air grill cover that mounts over the evaporator panel in the freezer compartment. Replace if cracked, broken, or tabs are damaged or missing.
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.