Kenmore / Sears Dishwasher Dispenser Parts

The part went on easily. U Tube video answered any questions I had before installing. Read more

Twist the old one out, insert tab, twist until other side snaps in. Easy as pie after watching the video! Read more

First unplug or turn off the electrical breaker to the dishwasher. Then I removed the phillips head screws holding the inner door to the outer door panel. I then removed the hex head screws holding the dispenser assembly. The electrical connection needs to be disconnected and then reverse the procedure to install the new dispenser. Restore power to the dishwasher and your done. Read more

• Will not dispense detergent

I ordered a new soap dispenser and began a new venture in repairing my dishwasher. I turned off the breaker that suppled power to the unit. I removed all the T-15 torx screws from the inside cover except one, which my wife helped me hold in. This prevents the cover from dropping off. Then, after removing those two, we closed the dishwasher cover, and lifted off the outside cover. That being off, I saw the two wires connecting the dishwasher dispenser solinoid. Removed them. Notice, that one... Read more

After having seen the video I installed the new lid and it worked. Read more

Since door latch parts are not available, I replaced the entire dispenser assembly. While waiting for the part to arrive, I watched the installation video, which made the installation quite easy. Read more

First replaced the latch, spring, and lever, but no improvement. Then I saw the lever arm on the other half of the door, which by position had to be the way that the timer interacts with the soap dispenser. After turning off the power to the dishwasher, I removed the switch cover (not obvious how -- a video would help: on the left, I slid the narrow rectangular plastic wire cover a little to one side and gently opened it on its little hinge, which is near the left side of the door, and then... Read more

After having seen the video I installed the new lid and it worked. Read more

First replaced the latch, spring, and lever, but no improvement. Then I saw the lever arm on the other half of the door, which by position had to be the way that the timer interacts with the soap dispenser. After turning off the power to the dishwasher, I removed the switch cover (not obvious how -- a video would help: on the left, I slid the narrow rectangular plastic wire cover a little to one side and gently opened it on its little hinge, which is near the left side of the door, and then... Read more

Appeared to be two problems: the latch was worn and one of the pins that slid in a guide on the actuator located in the inner panel had broke off. Detergent lid spring and pin appeared to be OK but decided to replace since I was aready working on it. I ordered all the inner panel mechanism from the control arm to the latch actuator on the inner panel. The repair was successful as the detergent dispenser now opens during its cycle. Read more

• Will not dispense detergent

I bought a replacement part and changed it out. Read more

Although I ordered the latch, lever and a new cup and replace the original pieces the dispenser still did not close. On further inspection it turned out to be a small spring that had fallen out of place. Once the spring was reconnected the dispensing cover worked fine. I'm still happy that I replaced the entire assembly with new parts regardless. Discovering the loose spring took the most time. Read more

Appeared to be two problems: the latch was worn and one of the pins that slid in a guide on the actuator located in the inner panel had broke off. Detergent lid spring and pin appeared to be OK but decided to replace since I was aready working on it. I ordered all the inner panel mechanism from the control arm to the latch actuator on the inner panel. The repair was successful as the detergent dispenser now opens during its cycle. Read more

We ordered the dispenser cover kit. the problem was with the spring. followed your "how to" video and it was a quick and easy fix! Read more

I watched the video on your site and it showed step by step how to replace the spring. Excellent shipping time. Good customer service on chat forum. Read more

This was a pretty easy fix. Removed the screws around the perimeter of the inside cover of the door and pressed the outer door cover upward to release it from slots retaining it. There are four wires to remove (2 for the detergent door release and 2 for the rinse agent release). Removed the 6 screws retaining the dispenser assembly and inserted the new one. Reassembly is simply in reverse order. Problem solved for less than the cost of a service technician's call! Read more