Kenmore / Sears Dryer Gasket & Seal

Replace your dryer door gasket to restore an airtight seal and prevent heat loss. Installs in minutes—just pull out the old, snap in the new. Confirm fit.

Dryer drum seal creates an airtight barrier between the rotating drum and housing to maintain drying efficiency. Replace if cracked or hardened. Verify fit with your model number.

This gasket is a sealing component used in select appliances. It fits between two mating parts to keep water or air where it belongs, helping prevent leaks and ensuring proper performance. What it does:

• Forms a tight seal between components or housings
• Helps prevent water drips, seepage, or air leaks at the joint
• Maintains correct appliance performance by keeping moisture/airflow contained
• Replace if the gasket is cracked, torn, flattened, or misshapen
• Common signs include residue, moisture, or visible gaps around the seal

• 1 gasket

• Disconnect power; turn off the water supply before servicing
• Note the orientation of the old gasket prior to removal
• Clean and dry the mating surfaces; remove any old gasket residue
• Seat the new gasket evenly without stretching; reassemble and check for leaks or proper seal

Replace your worn dryer door seal to restore a tight closure, contain heat and moisture, and eliminate rattling or squeaking. Easy snap-in install.

This replacement seal restores a tight barrier at its mounting point in your appliance. It helps prevent leaks and maintains performance by ensuring a proper fit between connected components where fluids or air must be contained. Location varies by model.

• Creates a reliable seal between mating parts to contain water or air
• Helps stop drips, seepage, and unwanted airflow that can affect performance
• Replace if cracked, flattened, swollen, or leaking
• Common symptoms: moisture under/around unit, residue, or diminished efficiency
• Direct-fit replacement to match the original part's size and profile

• Disconnect power and, if applicable, shut off water supply before servicing
• Note the original seal's orientation; clean and dry all sealing surfaces
• Lightly moisten or use only manufacturer-approved lubricant; avoid petroleum products unless directed
• Seat evenly without twisting; after reassembly, run a test cycle and check for leaks

Seals the dryer door perimeter to contain heat and prevent air leaks. Replace if damaged, stretched, or pulled off during cycles. Confirm fit with your model.

Seals the dryer door to contain heat and prevent air leaks. Replace if torn, cracked, or causing poor drying performance. Confirm fit with your model.

Heat-resistant fiberglass gasket seals your oven door perimeter to maintain consistent temperatures. Replace when worn, frayed, or flattened to restore efficiency. Verify fit by model number.

Fiberglass-reinforced door seal that restores airtight closure to maintain consistent temps and reduce energy waste. Replace if torn or compressed.

Seals the coupler connection on portable dishwashers to prevent leaks at the faucet adapter. Replace when worn, cracked, or flattened to stop drips.

Seals the gap between drum and bulkhead to reduce air leaks, prevent lint buildup, and quiet operation. Replace if torn or worn. Adhesive required.

Vinyl door seal lines the dryer door perimeter to block air leaks and cushion closure. Replace when worn or cracked to restore a tight seal. Verify fit by model.

Replacement door gasket that seals the refrigerator/freezer door to help keep cold air in, reduce energy loss, and maintain consistent temperatures for stored food. What it does

• Forms an airtight seal around the door to prevent warm air from entering the compartment.
• Helps maintain even cooling and prevents frost or ice buildup caused by air leaks.
• Can reduce running time and energy use when the original gasket is torn, warped, or no longer seals.
• Common symptoms of a failing gasket: visible gaps, condensation or frost at the door, uneven temperatures, or increased energy use.

• Disconnect power to the appliance and remove food from affected areas before beginning work.
• Inspect the door frame for dirt or debris and clean mating surfaces before installing the new gasket.
• Align the gasket to the door and seat it fully—follow OEM alignment steps for your model; if the gasket is stiff, warm it slightly per OEM guidance to help fit.

Replaces worn or stretched dryer door seals that allow heat to escape. Maintains proper drying temperature. Verify fit with your model number.

Felt pad installs under the drum glide to prevent metal-on-metal contact and reduce friction. Replace if worn, causing grinding noise or squealing.