Need Help?
Call or text
Seals the rear drum edge to contain hot air and improve drying efficiency. Replace if worn, torn, or causing noise. Confirm fit with your model number.
Our 19 year old Whirlpool dryer quit heating. After checking the thermal fuse, I found the ignitor electrically open. I bought an ignitor at a local store as there was a national holiday the next day and I did not want the dryer inoperative waiting several days for shipping. I can say AppliancePartsPros is MUCH cheaper for the identical Whirlpool genuine part. While changing the ignitor, I noticed there was an excessive amount of lint in the dryer, which was caused by worn drum seals. I ordered... Read more
Seals the gap between the drum and front panel to prevent air leaks and noise. Replace if worn, damaged, or causing squeaking sounds. Verify fit with your model.
Found the entire top bearing support plastic piece was completely worn through, the bearing slides had all disappeared some time ago. So it was obviously the problem. The felt trap duct (which is actually a drum seal along bottom front of drum so I don't know why they call it felt trap duct) had also disappeared, so a lot of lint was getting inside the front panel too. It's a very easy repair to change the bearing support; everything just pops out just like the video shows. Make sure you... Read more
Seals the drum perimeter to prevent abrasion and maintain temperature. Replace when worn, torn, or causing marks on clothes. Verify fit by model number.
Maytag Gas Dryer Model: MGDE300VW1 I had previous experience with repairing my dryers, but this was a first for this model. Instructional videos very helpful. Ordered necessary parts and they were delivered with-in two days. Wow! Squeak found to be coming from idler pulley roller which no longer turned freely . The four other cabinet rollers had signs of wear. Dryer belt had frayed edges and a couple of burn spots in the belt from the motor turning before the drum did. Cleaned up all shafts... Read more
Seals the lint screen housing to prevent air leaks and maintain proper airflow. Replace if damaged, missing, or causing lint buildup. Verify fit.
Seals the blower housing to prevent air leaks that reduce drying efficiency. Replace if worn, cracked, or missing to restore optimal airflow.
Watched You tube videos to narrow the problem down to old deteriorated gaskets. Read more
Seals the gap between drum and front panel to prevent air leakage and clothes snagging. Replace if worn, torn, or causing thumping noise. Verify fit.
My 12 year old Frigidaire stack on top dryer had been beeping distress messages in some unintelligible code for about a year when it completely stopped producing heat. It also had a long standing issue with delicate fabrics and thin straps or drawstrings getting caught in the drum. After using this site to troubleshoot and viewing the useful how-to videos, I ordered and replaced the heating element, thermal limiter, and felt seals. Based on others' stories, I decided to also replace the rear... Read more
The Seal is an OEM part for Whirlpool dryers. This specific seal is designed to fit around the blower housing, ensuring a tight seal that prevents air leaks within the dryer. The blower housing is a critical component of the dryer's air circulation
Replace your dryer drum seal when clothes take longer to dry or you notice lint buildup. Maintains heat efficiency and prevents air leaks. Confirm fit with your model number.
From reading "troubleshooting" sites on the internet, originally thought I'd be replacing the front & rear drum rollers, so I ordered the rollers, and a new belt before I opened up the dryer, taking it out of use. When I opened it up the front rollers were "shot", and the front bulkhead was "totaled". Waited for parts to arrive (within 2 days), and successfully replaced front & rear rollers, bulkhead, drum seal. The on-line videos really helped me ensure I was keeping in the right order. My... Read more
Seals dryer door to prevent heat loss and improve efficiency. Replace when torn, frayed, or loose. Fits in door groove; may need adhesive for install.
Purchased the gasket, but upset with myself I forgot the high temp adhesive.....a 13$ part and now 7$ for shipping. Think not for my mistake Read more
The Door Seal is an OEM part for Whirlpool dryers. It forms a tight seal around the dryer door, preventing heat from escaping and ensuring efficient drying performance. This seal helps to maintain the internal temperature of the dryer, optimizing energ
I replaced the gasket. Removing the old one was not easy. I used a razor knife to cut out most of it. And then I used rubbing alcohol to soften the remaining glue and scrapped it out with a small blade screwdriver Read more
Seals the gap between drum and front panel to retain heat and reduce friction. Replace if worn, torn, or clothes catch in drum. Verify fit with model number.
Replaced the upper and lower felt strips and drum glides. Dryer running much quieter and not tearing clothes. Read more
The Shaft Seal is an OEM part for Whirlpool washing machines. This seal is designed to fit around the shaft that connects the tub to the transmission or motor, preventing water from leaking out of the tub and into the machine's internal components.
Just like the one's I have worked on for 30 years for Whirlpool. Read more
Seals the gap between drum and front panel to retain heat and reduce friction. Replace if worn, torn, or causing noise. Confirm fit with your model.
Filters debris from water entering your washer and seals the hose connection. Replace if water fills slowly or screens are clogged. Confirm fit by model.
As a Mechanic, I did the common sense approach: INITIAL OBSERVATIONS & CHECKS: - Unplug Machine & check inlet water hose connections for leaks and signs of hose failure; - Remove back panel & inspect for water presence at all hose connections, pump, bottom of basket (bottom center of basket where the main motor, shaft bearing, and tub seal is located), dispensers, bottom of wash basket, water injector area, look everywhere where there is a hose connection and where water flows... - Inspect... Read more
Felt pad installs under the drum glide to prevent metal-on-metal contact and reduce friction. Replace if worn, causing grinding noise or squealing.
I went on line and purchased all of the possible parts that could be worn out. I spent less than the service guy wanted to show up...The online videos were spot on. Two hours and it works like new! One of the best values on the Internet! Read more
The O Ring is an OEM part for GE dryers, creating a tight seal in different components for efficient operation. This small part prevents air leaks that can impact drying performance, made from quality materials to withstand high temperatures and freque
Went ahead and replaced the pulley as well the drum bearing sleeve and O ring, drum belt and the front drum bearing slides. Put the unit back together and she ran like a top! Read more