Kenmore Elite Parts

This DC motor powers the appliance's cooling fan to move air across coils and through compartments. Replacing a weak or failed motor restores proper airflow for steadier temperatures and quieter, more efficient operation. What it does:

• Drives the fan that circulates air through the evaporator or across the condenser
• Helps maintain even cooling and prevent temperature swings
• Replaces a motor that won't start, runs intermittently, or makes grinding/squealing noises
• Can help address poor cooling, warm spots, or frost/ice buildup from lack of airflow

• 1 DC motor

• Disconnect power before servicing; wear cut-resistant gloves
• Access the fan area per service information (rear interior panel or machine compartment)
• Transfer the fan blade and any grommets/brackets/screws from the original motor if needed
• Seat the motor securely, route wires clear of the blade, and verify the fan spins freely before reassembly

This adjustable leveling leg screws into the dryer base to support and stabilize the cabinet. Replacing a worn or missing foot helps level the appliance, reduce vibration and noise, and keep it steady on uneven floors.

• Provides threaded height adjustment to properly level the dryer
• Stabilizes the cabinet to minimize rocking, vibration, and walking
• Replaces a broken, worn, or missing foot
• Common symptoms: dryer wobbles, is hard to level, or makes rattling/vibration noise

• Disconnect power; shut off gas supply for gas models
• With a helper, carefully tilt or raise the dryer for access
• Unscrew the old leg; thread the new leg into the base by hand, then adjust with a wrench until the dryer sits level and stable
• Ensure all legs contact the floor and the dryer does not rock

Element won't heat or overheats? This infinite switch kit restores precise temperature control to your cooktop's burners. Fixes erratic heating issues.

Fix a refrigerator that stopped making ice or produces slow, irregular ice cycles. This ice maker assembly restores automatic ice production. Moderate DIY.

If your gas range burners won't ignite or click continuously, the spark module may have failed. This repair typically takes 30-45 minutes.

Oven light stays on or won't turn on when door opens? This door-activated switch restores automatic light control. Easy 15-minute DIY repair.

The Burner Valve is an OEM component specifically designed for Frigidaire ranges. It controls gas flow to individual burners, providing a selection of different heat levels when operating the cooktop.

Causes of a bad burner valve can include wear over extended usage periods, damage from water, or gas blockage impeding operation. 

Symptoms of a bad burner valve include:

• Inability to light specific burners or adjust the flame height
• Uneven or intermittent burner performance  
• Gas leaks at burner valve connections
• Recurring error codes due to valve malfunctions

Replacing with this OEM valve restores full functionality to the range cooktop. Compatible with existing gas lines, it supports safe and reliable cooking performance.

This OEM Frigidaire replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. Replace before issues worsen.
 

This fan grille assembly covers and protects the refrigerator's fan while channeling airflow through the vents. Replacing a cracked or missing grille helps restore proper air circulation and can reduce noise and temperature fluctuations.

• Shields the fan blades and prevents items from contacting the intake
• Directs airflow to support even cooling throughout the compartment
• Typical symptoms: broken louvers or tabs, rattling/vibration noises, obstructed airflow, frost or warm spots near the fan area
• Restores the original airflow path and appearance after damage

• Disconnect power and clear shelves/drawers to access the panel
• Remove the screws/clips securing the old grille and retain any reusable hardware
• Position the new grille and fasten securely; ensure the fan spins freely and vents are unobstructed
• Restore power and allow temperatures to stabilize

Controls and stabilizes incoming gas supply to burners and oven. Replace if regulator is cracked, leaking, or fails to maintain consistent gas pressure.

Dryer stops mid-cycle or won't start? This door latch assembly secures the door to keep your dryer running. Simple 2-minute DIY fix for most models.

This door latch assembly secures the appliance door closed so cycles can start and run safely. A worn or damaged latch can prevent the door from locking, stopping the unit from operating or causing it to pause mid-cycle.

• Engages with the door strike to keep the door closed and locked during operation
• Faulty latches can lead to the door not locking, cycle not starting, or errors indicating an open door
• Also cause intermittent stopping if the latch doesn't stay engaged

• Disconnect power before servicing
• Handle wiring connectors carefully; note their positions for reassembly
• Align the latch with mounting points and tighten fasteners securely
• Test door closure and operation before returning to service

12 Ft in length

Dishwasher drain hose channels wastewater from the pump to your home plumbing. Replace if cracked, kinked, clogged, or leaking to restore proper drainage.

This is the condenser fan motor for select LG-built refrigerators. It drives the outside rear fan that pulls air across the condenser coils and over the compressor to remove heat so the refrigerator can cool efficiently.

• Circulates air through the condenser section to dissipate heat
• Helps prevent overheating of the compressor
• Common failure symptoms: fridge not cooling well, compressor running hot, loud or grinding noise from rear bottom, fan not spinning
• May run intermittently or seize when failing

• Disconnect power before servicing; use cut-resistant gloves
• Access from the rear lower service panel near the compressor
• Note wire orientation and fan blade position before removal
• After replacement, ensure the fan spins freely and no wiring contacts the blade

This factory screw secures panels, brackets, and other components in your cooking appliance. Replace a missing, stripped, or corroded fastener to restore a tight, rattle-free fit and keep parts properly aligned during use.

• Fastens components to maintain proper alignment and stability
• Helps prevent vibration, rattling, and loose parts during operation
• Replace if threads are stripped, the head is damaged, or the screw is missing
• Commonly used to mount internal or exterior parts in ranges and wall ovens

• Disconnect power and allow the appliance to cool; shut off gas supply if applicable
• Use the correct driver bit to avoid stripping the screw head
• Install in the original location and do not overtighten
• If the receiving threads are damaged, repair or replace the mating part before installation

Includes vinyl rack repair touch up paint and tine tip covers. Color: Grey