Kenmore Elite Parts

This is the DC motor that drives the condenser fan, typically located near the compressor at the bottom rear of the refrigerator. It circulates air across the condenser coils to dissipate heat and maintain efficient cooling. Replace this motor if the refrigerator is running warm, the compressor is overheating, or the fan is not spinning when the compressor is operating.

This factory screw secures panels, brackets, and other components in your cooking appliance. Replace a missing, stripped, or corroded fastener to restore a tight, rattle-free fit and keep parts properly aligned during use.

• Fastens components to maintain proper alignment and stability
• Helps prevent vibration, rattling, and loose parts during operation
• Replace if threads are stripped, the head is damaged, or the screw is missing
• Commonly used to mount internal or exterior parts in ranges and wall ovens

• Disconnect power and allow the appliance to cool; shut off gas supply if applicable
• Use the correct driver bit to avoid stripping the screw head
• Install in the original location and do not overtighten
• If the receiving threads are damaged, repair or replace the mating part before installation

This spark module supplies the high-voltage pulses that ignite the surface burners on a gas cooktop or range. Replacing a failing module helps restore consistent clicking and spark so burners light promptly and reliably.

• Supplies high-voltage to up to five surface igniters (5+0 configuration)
• Sends spark when a burner control is turned to Lite
• Failure symptoms can include no spark on all or multiple burners
• May also cause intermittent/weak spark or continuous clicking

• Disconnect power and shut off gas before servicing
• Note wire locations; move one connector at a time to matching terminals
• Mount securely in the original position and ensure proper grounding
• After replacement, if only one burner won't ignite, inspect that burner's switch and igniter

Burner won't heat or gets no power? This surface element supplies heat to your cooktop. Easy DIY fix—test for power at terminals first.

Plastic cap that snaps over refrigerator door handle ends to cover mounting screws and finish the handle. Replaces lost, cracked, or broken caps.

If your refrigerator light stays on or interior won't cool properly, the door switch may have failed. This magnetic switch detects door position.

The dishwasher rack repair kit provides components to fix damaged dish racks, including replacement wheels, tines, and clips. Use this kit when rack wheels break, tines bend or snap off, or the rack becomes difficult to slide in and out smoothly.

Thermal fuse that protects the washer motor circuit from overheating. Interrupts power if motor temperature exceeds safe limits. Replace if washer stops mid-cycle or won't start.

This is an adjustable leveling leg that threads into the base of the dishwasher to support the unit and allow height adjustment. Proper leveling ensures the door seals correctly and water drains efficiently. Replace this leg if it is broken, stripped, or missing, which can cause the dishwasher to rock, leak, or not close properly.

Rear support wheel for dishwasher lower rack assembly. Replaces broken, cracked, or missing wheels that cause dragging or misalignment on the track.

This is a door-activated switch that detects whether the oven door is open or closed. It controls functions such as the oven light or signals the control board about door position. Replace this switch if the oven light stays on or off regardless of door position, or if the oven does not operate correctly due to a faulty door signal.

If your refrigerator isn't cooling evenly or the freezer is noisy, the evaporator fan motor may have failed. This motor circulates cold air throughout.

Glass scraper tool for cleaning cooktop surfaces. Removes stuck-on food, spills, and residue from glass cooktops. Essential for maintaining appearance.

Oven light not turning on when door opens? This door-activated switch detects door position and controls interior lighting. Easy push-in installation.

This is a roller assembly that attaches to the lower dishrack of a dishwasher, allowing the rack to slide in and out smoothly. The roller includes the wheel and its mounting bracket. Replace this part if the lower rack is difficult to pull out or push in, rolls unevenly, or if the existing roller is cracked, worn, or missing.

White dishwasher rack repair kit includes 150 tine tips and vinyl paint to cover chipped, rusted, or worn rack tines. Extends rack life and prevents rust.