Kenmore / Sears Hinge Parts

Supports and pivots the freezer door at the top hinge point. Replace this hinge if cracked, broken, or worn to restore proper door alignment and swing.

Supports and guides the refrigerator door as it pivots, reducing friction. Replace if cracked, worn, or causing metal shavings to restore smooth operation.

Supports and guides your range oven door for smooth opening and closing. Replace if your hinge is cracked, broken, or causing door misalignment issues.

Kit of 4 pins that insert into oven door hinges to safely remove the door for repairs or cleaning. Replace lost or damaged pins during door removal.

Refrigerator door hinge assembly that mounts at the C position. Replace if your hinge is cracked, broken, or worn to restore proper door alignment and seal.

Replacement door hinge assembly for side-by-side refrigerators. Mounts the door to the cabinet frame. Replace if cracked, bent, or worn for proper alignment.

This bottom hinge replaces the lower door pivot on compatible Frigidaire refrigerators to restore proper door alignment and smooth opening. It provides a secure pivot point to help maintain an even close and consistent seal. What it does:

• Supports and pivots the lower edge of the refrigerator door for smooth opening and closing.
• Helps maintain correct door alignment so the gasket seals evenly.
• Common replacement for doors that sag, bind, or do not close evenly.
• Works with the factory mounting hardware and hinge locations on compatible models.

• Disconnect power and remove food and loose items from the door before starting.
• Always support the door while removing or installing the hinge to prevent injury or damage.
• Use appropriate hand tools and avoid overtightening fasteners; check door alignment after installation.
• Refer to your model's service manual or official parts diagram for model-specific steps and torque specs.

Replacement washer door hinge that secures and aligns the door for smooth opening and closing. Needed when original hinge is cracked, broken, or worn.

The door stop bracket is a metal or plastic bracket that mounts to the appliance cabinet or door frame to physically limit how far the door can open, protecting the hinges and surrounding cabinetry. It works alongside other door stop components to keep the door from swinging past a safe angle. Replace this bracket if it is bent, cracked, missing, or your door swings open too far and is stressing the hinges.

Cushions and limits freezer door movement to prevent over-travel and reduce impact noise. Replace when cracked, worn, or missing to restore smooth operation.

This stop-door is a small replacement door stop that helps control how the appliance door closes and rests, restoring proper door movement and preventing over-travel or binding. What it does:

• Cushions and limits the door's travel to prevent slamming or over-rotation.
• Helps the door align and latch correctly when closing.
• Can reduce door sag or rubbing caused by a worn/missing stop.
• Addresses symptoms such as a door that closes too far, hangs unevenly, or doesn't sit flush.

• High-level, two-person recommended for larger doors; support the door before removing fasteners.
• Disconnect power (and water if applicable) and follow manufacturer safety guidance before servicing.
• Use appropriate hand tools; inspect adjacent hinges and fasteners and replace if damaged.

Replacement hinge for refrigerator doors. Mounts to cabinet and door frame to support smooth opening and closing. Needed when hinge is cracked or worn.

This replacement refrigerator door hinge keeps the door aligned and operating smoothly so your appliance seals and closes properly. It restores proper door movement and helps prevent drafts and uneven wear. What it does:

• Supports the refrigerator door and maintains correct alignment for a tight seal
• Allows smooth opening and closing of the door without binding
• Helps prevent door sag, rubbing, or gaps that can cause temperature issues
• Fits where the original hinge mounts to the cabinet or door depending on model

• Disconnect power and remove contents from the door before starting work
• Support the door while removing and installing the hinge to prevent dropping or damage
• Use the original fasteners or OEM-recommended hardware; tighten screws securely but avoid over-torquing

Center door hinge assembly for bottom-mount refrigerators. Supports the door weight and maintains proper alignment. Replace if cracked, worn, or broken.