Kenmore / Sears Range Parts

I purchased a new oven floor!! It only took me 15 minutes to get the other floor out & then place the new floor into position. There were only 2 screws. Read more

Using the parts I ordered, I replaced the glass myself following the very helpful video on your web site. Read more

Replace two door hinges works great now. Read more

Replaced numerous items including this Inverter and two control boards but the Magnetron was the ultimate solution. The tip was clearly burned through when I removed the original. Read more

Oven part was hard to fix as space was very small, it took longer than even you tube video said it would Read more

Ohmed the oven heat elements and oven sensor, they checked out fine. No broken or bad connections. Figured it had to be high limit switch opening or control panel. With Christmas meal around corner I ordered both. Oven working fine and my wife is happy. Read more

In the middle of Christmas baking, I noticed that it was taking a really long time to bake bread. Since I had already done 5 batches and the timing was always the same, I knew when I had to add 20 min, something was wrong. My oven thermometer (I bought at target) no longer worked so it was hard to tell the exact temperature. First, I went and bought a new thermometer to see the actual temp, then I set the oven to 350 degrees and checked to see what the thermometer was showing. It was almost 50... Read more

• Element will not heat

I diagnosed the problem, found Appliance Parts Pros and watched their video. It was as easy as the video they made said it would be. Overall an amazing experience. I was quoted $250 to have the repairman come do the same thing. My cost was $40. Read more

Replaced the old valve with a new one from AppliancePartsPros.com. I watched one of the YouTube videos to get an idea of what the process would entail. I gathered the tools I would require, plus a work light. The repair/replacement went pretty good. One thing the video I watched didn't cover was adjusting the valve for a propane system. I compared my old valve to the new one and saw that I would have to screw down the oven gas outlet until it "bottomed out". Read more

Replaced the ignitor module ( a plug in direct replacement) a monkey could have performed this repair Read more

Found the parts I needed ordered them from your site Received them and installed in a few minuets and was done Read more

Second repair after 10 years of service - igniter had cracked and spill overs were causing the others to misfire. This was a two-step process. I took apart the cooktop to see what parts were neded. Screws were all rusted, I had to drill ome out. The burner gaskets broke during the process and needed replacement. One of the burners had deformed due to excess heat. After that initial diagnose, I reassembled the cooktop without the igniters and ordered all the parts I needed. The second stage was... Read more

When the element on our 15 year old builder grade oven went out we were worried it was time to spend thousands on a new oven. Instead, we found the replacement part on appliancepartspros.com and decided to give replacing it a shot, after all it was $80 instead of $1600. We weren't entirely sure the replacement was the right part because our oven model had an extra "0", but given it came up when I searched for the oven model (if not on the compatability checker) and the refund guarantee we... Read more

Secured the inner and outer door together and screwed handle back in place. Read more

• Little to no heat when baking

The stove was a 40 year old drop in model so we had to turn off the breaker to the oven before getting started. We removed the baking racks then used a small drill bit to remove the old baking element making sure not to allow the wire to slip back into the back of the stove (very important). Installed the new baking element by slipping the wire connector onto the new element. Replaced the screws, restored power, tested the oven and voila it worked. Easy peasy. Read more

• Element will not heat
• Little to no heat when baking
• Oven not heating evenly

Removed 2 sheet metal screw pulled element out about 2 inches. Removed two Spade connections. Removed the element from the oven. Inserted the new element into the over, connected the two spade connector. Reinstalled the two sheet metal screws. Set the oven to bake for testing and tested until the element turned red. Total time less than 5 minutes. Read more