Your privacy choices: We and our partners use cookies for analytics and ads. Decline all turns them off.
Privacy Policy · Do Not Sell or Share My Personal Information
Need Help?
Call
Fix ice maker not producing ice or making misshapen cubes with this refrigerator ice tray assembly. Straightforward DIY repair for common ice issues.
Ice maker won't stop making ice or overflows? This refrigerator ice maker control arm regulates ice production cycles. Straightforward repair.
Fix a refrigerator that stopped making ice with this complete ice maker assembly. DIY-friendly installation takes about 10 minutes with basic tools.
I replaced the icemaker. It was fairly easy, with the most difficult part being access to the icemaker in the bottom freezer. I loosened two screws, removed one additional screw, disconnected the wiring and removed the old icemaker. I mounted the wiring harness and ice level sensor arm from the old unit onto the new icemaker and installed it with no problems. I wish I'd done this months ago instead of repeatedly attempting to repair the old icemaker. Read more
Usually ships within 4 - 14 days
Ice bin cracked, warped, or causing weak dispensing and jams? This ice bucket assembly stores and delivers ice to your dispenser. Easy DIY repair.
After doing research on broken ice bucket for an LG refrigerator on numerous sites I became totally confused on all the different #s that showed up. Contacted AppliancePartsPros. I was assured they had the part needed. Part arrived perfect match. Took more time removing part from shipping box than installing. Part I ordered is mostly plastic so all the bubble wrap made sure it wasn't broken in transient. If I need to order more parts this is the go to site. Larry Read more
The Ice Cube Tray is an OEM part for LG refrigerators. It is located in the freezer section of the refrigerator and provides a designated space for freezing water into ice cubes. It is designed with individual compartments to form ice cubes in a specific shape and size.
Causes of a faulty ice cube tray can include regular wear and tear, physical damage, or improper handling. These factors can result in issues such as the tray cracking or breaking, difficulty in removing ice cubes, or improper freezing of the cubes.
Symptoms of a bad ice cube tray may include:
This OEM LG part can also be used on Kenmore/Sears appliances.
It was a snap. All I had to do was unsnap one end of where the ice tray attached to the ice maker and fit the tray into the two sides and then resnap the end back onto the icemaker. Very easy. Read more
Fix ice dispensing issues caused by bent or dull crusher blades. This blade restores smooth crushed-ice flow. Quick DIY replacement with video guide.
I ordered (3) new replacement blades and received them in two days! Read more
Used to prevent over ice production in the ice dispensing bucket.
Replaced th sleeve around he auger. Read more
Ice maker not dispensing cubes properly? This stripper arm guides ice through the maker. Common fix when tabs break. Takes about 15 minutes to install.
New slide Read more
This ice ejector is the plastic arm that pushes cubes out of the ice maker mold and into the ice bin, restoring proper ice ejection and dispenser function. It's a direct-replacement component for affected ice maker assemblies. What it does:
Ice sits on top and won't fall into bin? This ice maker stripper pushes cubes into the collection bin. Simple DIY repair, just remove and replace.
Removed and replaced damaged part. Read more
Ice maker not ejecting ice cubes properly? This stripper arm restores correct movement and alignment in your refrigerator's ice maker. DIY-friendly repair.
Replaced the ice maker. Read more
Ice maker not dispensing cubes or producing hollow ice? This ice maker ejector controls the ice release cycle. Moderate DIY repair for most models.
Ice maker not ejecting cubes or jammed? This ejector arm controls ice cube release from the mold. Common fix for ice production issues in minutes.
This ejector arm sweeps across the ice maker mold to push finished ice cubes out and into the storage bin. It is a dual-arm design for an 8-cube ice maker tray. Replace this part if ice cubes are not being released from the mold, the arm is bent or broken, or the ice maker is cycling but not dispensing ice into the bin.
Opt-Out Request Honored
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.