Kenmore / Sears Wall Oven Parts

Knowing the odds of 2 failures occurring at the same exact time was unusually high, I just searched your site for what other broken items might affect these two failures. Came up with next control item upstream and tallied that item failure with percentages of successful repairs, (4 mins.) door safety switch. Since I had to change out the most likely of the 3 and since I was already was going to be into the switch panel I ordered all 3 and swapped them all out to cover my butt, as they were... Read more

I ordered the infinite switch control from Appliance Parts Pro on a Wednesday afternoon and it arrived well packaged the next day even though I selected standard shipping. Thank you for the easy ordering and fast delivery! Replacing the old switch was easy: 1. Disconnect the power to the stove 2. Make sure the power is off to the stove 3. Pull 4 burner control knobs off and remove 4 large nuts attached to the 4 burner switches 4. Lift the face plate off and clean previously hidden cooking... Read more

Removed existing gasket and replaced with new gasket in less than 5 minutes. Very Easy. Make sure to remove the lower burner cover (inside the oven) which allows you to pull the end gasket material through the two circular openings in the frame. Read more

Initially, I took it off, sanded it and painted with appliance touch-up. Still didn't look good so I ordered a replacement part and installed. Read more

I ordered the part from APP, removed the door, removed the inside panel and replaced the glass. Hardest part was figuring out exactly which screws to remove to open the door. Read more

Ordered replacement parts Read more

Replaced the regulator with part #AP5802175. Watched the video when purchasing, and it was spot on. Would have taken me about 15-20 minutes if I had access to a vise, to remove one of the fittings. Was able to get it out using two wrenches, but it was not without a bit of elbow grease. The new part went in easily. Turned on valve on regulator, plugged in the power, turned on the gas valve, done. Everything worked fine. Easy job for anyone with just a few tools. Read more

Fast delivery, great service Read more

Going on line and viewing your website, you provided a very easy way to get me to a picture that was exactly what I wanted with the exact (old style) connections. I had previously gone to Home Depot twice, and I still did not get the correct burner that I needed. Your website was great, I should have gone there first. I used the part that I received from AppliancePartsPROS.com and replaced the defective, old and non-working surface element. It was easy, I used a screw driver to snap off a... Read more

These drip pans fit! I had bought some from a local big box store and they didn't fit. I only wish they still made them without the holes in the bottom of the drip pan. How's that supposed to hold a boil-over? But that's the manufacturer. AppliancePartsPros have always sent me orders right on time. Read more

• Won't start

Did some research to find out it was the electrode. Pulled out the old one to match what was on your site. It came in no time at all, and the replacement was a cinch. Read more

• Door won't close

I ordered both hinges (if the nylon roller was bad on the left, it was probably going to go bad on the right side as well). The web site was easy to navigate, order process simple. Hinges arrived quickly. Slide the oven door up and off. unscrew the three screws for the hinge. You need to then pull up with some force (there is a big spring in there), and twist the hinge to get the last bit out. I used a hemostat to hold the spring and keep it from falling back into the hole. removed the... Read more

Once I watched the video on your site about gas line install, it became apparent why the line bent when I raised the lid.. also discovered those two rods have nest to go into and the lid/top now sets down tight as designed ( and as an added bonus, gas smell disappeared during oven use) I ordered the gas lines with the model number, ordered all four …. it was a bit of a chore one came up when site opened I picked it, but did not know if it was the RH or LH etc.. so reading some of your answers... Read more

Replaced with new part Read more

If one control starts to fail the rest are sure to follow soon - so I replaced all four on our JennAir S160. Looked up the parts on line. Due to my background as an aviation electrician in the Navy and then working as an electrical systems designer for a defense contractor the toughest part was the clean up. Oh Well. Read more

• Door won't close

My dryer door would not stay shut because the door strike was stuck in the door catch. I was afraid that when I pulled the strike out, it would damage the catch, so I ordered the door strike and door catch. I got the damaged door strike out with needle nosed pliers in about 15 seconds. The door catch was in perfect condition so I didn't need to use the one I ordered. So then I proceeded to install the new door strike. That took me about 15 minutes because I did not have the manual strength to... Read more