Kenmore / Sears Wall Oven Parts

• Element will not heat

Ordered recommended part for GE appliance. Change was very simple. Followed instructions on video and removed one wire at a time. Very easy to change 5 to 10 minutes. Read more

Ordered replacement parts Read more

Well, I gotta say I was happy to find you still had parts for almost 20 year old microwaves. The microwave itself worked fine, so I hated to have to buy a new one, but I just couldn't take being hit in the head anymore; and my fix of using string and wire to tie it to the surrounding cabinets was unsightly to say the least. I'm glad I did some research and found this part - all I had to do was pop it in place and now the vent grill is secure. Problem solved with minimal cost. Read more

I am plagiarizing some info from the techs.. 1. Turn off the electrical supply to the range. 2. Remove the oven door and position it on a protected floor or "truck tailgate".(here I googled, "removing oven door on super capacity 465" ...my model had clips at the hinge that I had to pop out)... lay down the handle and outer door glass facing up. 3. Raise the top of the door and remove the two screws that secure the top of the door trim and the handle to the door liner, then remove the handle and... Read more

• Element will not heat

Replace burner and receptacle. The product arrived promptly after order and the receptacle came in a factory Whirlpool bag, indicating it was a genuine Whirlpool part. The burner did not have such identification, but works very good. I've placed 3 orders with these folks for various broken appliances, and each one has worked as advertised and performs like new. Read more

Replaced with new part Read more

Ordered correct replacement parts (your online form helped to identify correct valves 2 had black dot on inside stem for back small burner 1 had red dot for larger front burner). locked stove, turned off gas, unplugged cord. removed knobs, 5 screws and front plate also removed L shaped plate below knobs for better access to comp. fittings. pulled off ignitior controls loosened compression fittings (hard to get wrench on nut but doable), removed screw holding valve to manifold. reversed order... Read more

Replaced the switch infin by watching the video Read more

Once I watched the video on your site about gas line install, it became apparent why the line bent when I raised the lid.. also discovered those two rods have nest to go into and the lid/top now sets down tight as designed ( and as an added bonus, gas smell disappeared during oven use) I ordered the gas lines with the model number, ordered all four …. it was a bit of a chore one came up when site opened I picked it, but did not know if it was the RH or LH etc.. so reading some of your answers... Read more

• Door won't close

My dryer door would not stay shut because the door strike was stuck in the door catch. I was afraid that when I pulled the strike out, it would damage the catch, so I ordered the door strike and door catch. I got the damaged door strike out with needle nosed pliers in about 15 seconds. The door catch was in perfect condition so I didn't need to use the one I ordered. So then I proceeded to install the new door strike. That took me about 15 minutes because I did not have the manual strength to... Read more

• Element will not heat

Unplug range. Open oven door to gain access to the cook top lock-down screws, located under the front edge of the cook top. Tip the cook top up and carefully remove it by pulling forward. Set aside in a safe place. Remove old, burned-out, element by removing the single lock tab, located on one of the three mounting posts, then lift up. Leave the wiring attached. Flip the element over and remove the three mounting tabs, making note of their numbered locations. Transfer the mounting tabs to... Read more

GE Microwave/Convection Oven. Removed case (carefully). Tested in-line power cord fuse with multi-meter. Fuse was good. Noticed a scorch mark on a wire connected to the oven cavity thermal fuse. The fuse appeared to have been overheated from too much movement in it's mount. Removed part from unit and used number on the part to order a new one. Installed new part, re-assembled, and unit works fine. Read more

• Element will not heat

Ordered a new terminal block kit from Appliance Parts Pros. Shipping was lightening fast. Slapped the new part on my stove and its never worked better. Thanksgiving was saved! I'd replace the rest of my stove's terminal blocks if they weren't $50 a piece...sheesh! Read more

The glass was easily replaced. Just a few screws to remove cover then remove bad glass then i dropped in the replacement glass then reinstalled cover. Ithen put the door back in the stove. 15 minute job!!! I was so surprised to see how easy it was!!! Thanks! Part fit perfectly!!! Read more

Based on internet search and data found on APPLIANCE PARTS PRO, I deduced that the "infinite control " module was most likely bad. Replaced it and all is good. Toughest part was remembering how to disengage cooktop from down draft blower and then pulling the cook top up in within it's opening. Once pulled up, I put short 2x4's across the opening corners to support the cooktop safely while I worked on it. Next issue was figuring out exactly which screws held the glass top in place. As... Read more

Replaced switch with a new one. also replaced the 4 knobs Read more