Kenmore / Sears Wall Oven Parts

Best Seller

Genuine Frigidaire part

Kenmore Heating Element

By: Frigidaire

Part Number: 318255006

The Heating Element is an OEM part for Frigidaire ovens and ranges. It is responsible for providing the heat necessary for baking or broiling. The element converts electrical energy into heat through resistance; this heat is then distributed throughout the oven cavity to cook or bake food evenly.

Common causes of a bad Heating Element can include visible signs of damage like blistering, bulging, or breakage. A burnout may occur when the element overheats and fails, leading to no heat production. Additionally, electrical issues like a blown fuse or faulty wiring can prevent the element from receiving power.

Symptoms of a bad Heating Element include:

The oven does not heat up
Uneven cooking or baking
Longer cooking times than usual
The element not glowing when the oven is turned on

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

This part fixes the following symptoms

Little to no heat when baking
Oven not heating evenly
Won't start

Do-It-Yourself Stories from Customers like You My oven stopped working properly on convection roast setting was was only heating up to about 200 degrees Mark R. • Eastham , MA • May 15, 2015

One day, while trying to roast chicken on the convection roast setting, my Electrolux oven stopped heating properly. I tried the broil setting and the top electric heating element worked fine. I then tried the bake setting and found that the bottom element wasn't working at all. I Googled the problem. The info I found said that the issue was probably that the bake element needed to be replaced. It said to look for a break or burned through spot on the element. If it appeared OK, remove it... Read more

$146.95

Compare At:: $176.34
You Save:: $29.39

IN STOCK

Ships Today Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Kenmore Top Burner Receptacle Kit

4.9 (246)

By: Whirlpool

Part Number: 330031

The Top Burner Receptacle Kit is an OEM part for Whirlpool ranges and cooktops designed to provide a reliable electrical connection between the stove's top burners and the power source. This kit typically includes receptacles, wire terminals, and mounting hardware necessary for the installation, ensuring that each burner receives the proper electrical current to heat efficiently.

Causes of a bad top burner receptacle can include corrosion due to spills or moisture, physical damage from heavy use, or natural wear and tear over time.

Symptoms of a bad Top Burner Receptacle Kit include:

A burner that doesn't heat up
Intermittent heating or fluctuating temperatures
Visible signs of damage or corrosion on the receptacle
Sparks or short circuits when attempting to use a burner

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This part fixes the following symptoms

Element will not heat

Do-It-Yourself Stories from Customers like You Our range needed 4 new range top elements due to wear Dale D. • Orlando , FL • December 05, 2014

Personally I have experience working with electricity and knowing if I bought the part required this would be an easy fix. I got my model number and contacted Appliance Parts Pros and placed my order for the new elements, terminal blocks, and for appearance purposes 4 new Drip Pans. Excellent service and quick shipping. I ordered my parts on Sunday and received them on Tuesday. This was a simple repair that only required a screwdriver to remove the old terminal block from the range hood, wire... Read more

$15.66

Compare At:: $18.79
You Save:: $3.13

IN STOCK

Ships Today Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Kenmore Infinite Switch Top Burner Control Switch

4.9 (41)

By: Whirlpool

Part Number: WP3149404

The Infinite Switch is an OEM part for Whirlpool ranges and cooktops. This part controls the temperature of the small burner on electric ranges and cooktops by regulating the power supplied to the burner. The infinite switch allows for precise temperature settings, providing the flexibility to cook a wide variety of dishes by adjusting the heat level as needed.

Over time, infinite switches can wear out or malfunction, leading to issues with controlling the burner's temperature.

Symptoms of a bad Infinite Switch include:

The burner does not heat or heats intermittently
The burner heats to full power regardless of the setting
Inability to adjust the burner's temperature accurately
Physical damage to the switch, such as cracking or melting

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This part fixes the following symptoms

Element will not heat

Do-It-Yourself Stories from Customers like You Burners were working correctly most of the time but would stay in the on position (high )periodically and would not shut off automatically for the temperature you set the burner for Daryl B. • Gloucester , VA • August 12, 2021

Replaced the burner Infinite switches for the burners having the issue. Here are the latest part numbers for this model Maytag. Left rear (LR) and right rear (RR) burners are both 6" and use the same switch. Part # WP3149404. Left front (LF) is an 11 1/2" burner Part# W10167742. The right front (RF) burner is a double burner 6" center and 9 1/2" outside burner Part #WPW10149355. Very simple repair. Unplug the stove, remove the rear panel, remove the switch knob, remove the 2 switch screws,... Read more

$50.23

Compare At:: $59.77
You Save:: $9.54

IN STOCK

Ships Today Guaranteed

Add to Cart

Best Seller

Genuine Frigidaire part

Kenmore Outer Oven Door Glass

4.8 (43)

By: Frigidaire

Part Number: 316452758

This Outer Oven Door Glass is an OEM replacement part for Frigidaire ranges. It is the outermost glass panel on the oven door. It acts as a barrier to prevent heat from escaping the oven. If the glass is cracked or broken, it can lead to heat escaping and uneven cooking.

A broken outer oven door glass can be caused by a variety of factors, including accidental impact, thermal shock, or improper cleaning.

Symptoms of broken door glass can include:

Cracks or shattered glass
Difficulty maintaining the temperature inside the oven

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Do-It-Yourself Stories from Customers like You The outer door glass shattered when opening the door Robert C. • Lake Ozark , MO • May 21, 2017

I searched for my appliance and the problem. Applianceparts.com was one of the results. There was one fix-it help from a previous customer. I ordered the piece of glass and somehow it arrived at my home the VERY NEXT DAY! I couldn't believe it. So I followed the exact instructions left by the one person that wrote in. I removed 2 screws at the bottom of the door and 4 at the top which enabled me to disassemble the front and back of the door. I then cleaned all the shattered pieces of glass... Read more

$132.95

Compare At:: $158.21
You Save:: $25.26

IN STOCK

Ships Today Guaranteed

Add to Cart

Best Seller

Genuine Ge part

Kenmore Oven Bake Element

4.9 (319)

By: Ge

Part Number: WB44K5012

The Oven Bake Element is an OEM part for GE ovens. This element is located at the bottom of the oven and is primarily responsible for providing the heat necessary for baking. When the oven is turned on, electricity flows through the element, causing it to heat up and glow red-hot. This bake element has ¼” push-on wire terminals. If you are unable to use your old wire connectors, order TJMA02875-1.

Symptoms of a failing oven bake element include:

Oven not heating up properly or taking longer to heat
Uneven cooking or baking
Element not glowing or only partially glowing during operation
Visible signs of blistering, cracks, or holes on the element

Causes of oven bake element failure typically include general wear and tear from regular use, exposure to high temperatures which can weaken the element over time, or electrical issues such as short circuits.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This part fixes the following symptoms

Little to no heat when baking
Oven not heating evenly
Oven is too hot
Won't start

Do-It-Yourself Stories from Customers like You Element burn into Richard D. • Summerville , GA • April 02, 2014

Took out old element,got part number and look for the cheapest price online, Appliance Parts Pro could not be beat... order part be number, easy to match, came in fast and put in element, only needed a 5/16 nutdriver to take it out and put it in,unpluged wires and bent just a little to keep one on left and one right from getting mixed up and pluged up new element and ran in the 2 screws,easy job, dont get no easier.. Thanks again Appliance Parts Pro Read more

$61.64

Compare At:: $73.97
You Save:: $12.33

IN STOCK

Ships Today Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Kenmore Oven Bake Element

4.9 (248)

By: Whirlpool

Part Number: WP74010750

The Oven Bake Element is an OEM part for Whirlpool ovens. This crucial component is responsible for providing the heat necessary for baking. Located at the bottom of the oven, the bake element heats up when electricity passes through it, allowing your oven to reach the desired cooking temperature. This OEM Replacement Part has push-on terminal ends and measures approximately 23-5/8"wide x 15-3/8" long, with 3-3/8" inserts

Symptoms of a failing oven bake element include:

Lack of heat production when the oven is turned on
Uneven baking results
Visible damage to the element such as blistering or splits
A trip in the circuit breaker when the oven is activated

Causes of bake element failure typically include thermal stress causing material fatigue, accidental damage during cleaning, and electrical issues such as short circuits.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

If you are unable to use your old connectors order TJMA02875-1.

This part fixes the following symptoms

Little to no heat when baking
Oven not heating evenly
Element will not heat
Oven is too hot

Do-It-Yourself Stories from Customers like You The baking element was on fire Charles M. • Bandera , TX • March 30, 2014

I finally found the right serial number and found the part at Appliance Parts Pros. I was skeptical that they would send the element that had the correct rear brace fixture. when it came 2 days later i opened the box the Part was correct and it took about 15 minutes to replace since there are only two screws. My oven works fine now. THX Read more

$39.95

Compare At:: $47.14
You Save:: $7.19

IN STOCK

Ships Today Guaranteed

Add to Cart

Best Seller

Genuine Ge part

Kenmore Range Surface Burner Control Switch

4.9 (76)

By: Ge

Part Number: WB24T10029

The Range Surface Burner Control Switch is an OEM part for GE ranges. This switch manages the temperature of the surface burners on your range, providing the ability to adjust the heat level. Whether you're simmering sauces or boiling water, the control switch ensures precise temperature management, enhancing your cooking experience.

The causes of a faulty burner control switch often include prolonged use leading to wear on the electrical contacts, exposure to moisture causing short circuits, or physical damage from impact or excessive force when turning the knob.

Symptoms of a bad surface burner control switch:

The burner not turning on or off
Inability to adjust the heat level, with the burner staying at one temperature regardless of the knob setting.
Intermittent burner function

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This part fixes the following symptoms

Element will not heat

Do-It-Yourself Stories from Customers like You Large dual burner Frederick E. • Athens , AL • September 19, 2014

Stove is a GE Adora Model JBP63HH2bb. It took me forever to figure out how the burner was attached to the rails. My glass top was different than any instructions found on the internet for changing out a burner. The burners on this one are held to the bottom of the glass cook top by two rails that cross the bottom of the burner assemblies. In order to get too the burners you must remove 4 Phillips screws to lower the rails and burners from the cooktop. I suggest two people do this because... Read more

$37.26

Compare At:: $45.52
You Save:: $8.26

IN STOCK

Ships Today Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Kenmore Oven Igniter

4.9 (148)

By: Whirlpool

Part Number: W11596211

The Oven Igniter is an OEM part for Whirlpool ovens. It is responsible for igniting the gas to start the oven heating process. This igniter is crucial for ensuring that the oven reaches and maintains the desired temperature for baking and cooking.

Over time, the igniter can suffer from wear and tear, leading to inefficient ignition or complete failure. Causes of a bad igniter can include repeated heating cycles, electrical issues, or physical damage to the igniter element.

Symptoms of a bad igniter include:

The oven not heating up or taking too long to preheat
A noticeable gas smell due to incomplete ignition
The igniter glowing without igniting the gas

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Do-It-Yourself Stories from Customers like You Baking igniter burned out. Christopher C. • Pittsboro , NC • December 19, 2020

On my Jenn-Air downdraft range, the oven stopped heating. The broiler still worked. So pulled the pan off the bottom so I could see and found the igniter wasn't glowing to start the gas. I had replaced the full electronic control panel using Appliance Parts Pros so knew they had the full breakdown of parts for my model. I found the igniter and ordered. But frankly, I wasn't sure about doing the repair myself. It looked easy enough from videos and discussions here. Still, dealing with the... Read more

$61.95

Compare At:: $73.72
You Save:: $11.77

IN STOCK

Ships Today Guaranteed

Add to Cart

Best Seller

Genuine Ge part

Kenmore Surface Burner Terminal Block Kit

4.8 (88)

By: Ge

Part Number: WB17T10006

The Terminal Block Kit is an OEM replacement part for GE electric ranges. This kit replaces the points of connection delivering power to control circuits and surface coil elements atop the cooktop.

Causes of failure are prolonged heat cycling which slowly breaks down solder joints and insulator coating on terminals conducting power. Liquids spilled can seep into connection areas over time promoting electrical faults.

Symptoms of a faulty terminal block include:

Inability to ignite or regulate specific burners
Burners that glow intermittently or fail to respond
Tripped circuit breakers upon use of problematic zones
Buzzing or cracking noises from under cooktop areas

This genuine GE kit is also compatible with Hotpoint and RCA electric ranges.

This part fixes the following symptoms

Element will not heat
Won't start

Do-It-Yourself Stories from Customers like You THE TERMINAL BLOCK WAS BURN AND IT DOES NOT TURN HOT. Kenny W. • San Jose , CA • April 06, 2014

I ORDER THE TERMINAL BLOCK KIT, AND FOLLOW THE VIDEO HOW TO REPAIRE. IT IS VERY EASY.IT TOOK ME 10 MIN. Read more

$19.54

Compare At:: $25.40
You Save:: $5.86

IN STOCK

Ships Today Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Kenmore Oven Bake Element

4.9 (240)

By: Whirlpool

Part Number: 326791

The Oven Bake Element is an OEM part for Whirlpool ovens. This crucial component is located at the bottom of the oven cavity and is responsible for providing the heat needed for baking. The bake element converts electrical energy into heat, which is then distributed throughout the oven to cook food evenly.

Common causes of a bad bake element include excessive use, accidental damage during cleaning, or a power surge that can burn out the element.

Symptoms of a bad Oven Bake Element include:

The oven not heating up to the set temperature.
Visible damage to the element, such as blistering, cracks, or breaks.
Lack of heat when the oven is turned on
An increase in cooking times

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This part fixes the following symptoms

Oven not heating evenly
Little to no heat when baking
Element will not heat

Do-It-Yourself Stories from Customers like You Bottom coil of oven was not heating Charles W. • Suffolk , VA • February 04, 2017

I googled the model number of the oven and came across AppliancePartsPros.com The coil along with replacing video was right at hand. I ordered the part, got it three days later (standard shipping) and installed it. To sum it up, it was a five minute job. Read more

$57.95

Compare At:: $68.96
You Save:: $11.01

IN STOCK

Ships Today Guaranteed

Add to Cart

Best Seller

Genuine Ge part

Kenmore Oven Bake Element

4.9 (147)

By: Ge

Part Number: WB44K5013

The Oven Bake Element is an OEM part for GE ovens. This component is located at the bottom of the oven cavity and is responsible for generating the heat needed for baking. By converting electrical energy into heat, the bake element ensures even temperature distribution throughout the oven, allowing for consistent cooking results.

Causes of a malfunctioning Oven Bake Element may involve visible signs of wear or damage, like blistering or holes, a break in the element that hinders proper heating, and burnout or malfunctioning resulting from age or excessive use.

Symptoms of a failing Oven Bake Element include:

The oven not heating to the set temperature
Uneven baking results
No visible glow from the element when the oven is turned on
The oven taking longer than usual to preheat

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This part fixes the following symptoms

Little to no heat when baking
Oven not heating evenly

Do-It-Yourself Stories from Customers like You Lower oven bake heating element was broken in half Richard P. • Colleyville , TX • September 19, 2014

Watched the appliancepartspro video and changed it out. It took about 15 minutes. I'm sure I saved hundreds. Read more

$63.95

Compare At:: $76.10
You Save:: $12.15

IN STOCK

Ships Today Guaranteed

Add to Cart

Best Seller

Genuine Ge part

Kenmore Door Switch

4.9 (155)

By: Ge

Part Number: WB24X829

The Microwave Door Switch is an OEM part for GE microwaves, designed to prevent the microwave from operating when the door is open by interrupting the power whenever the door is not securely closed. The door switch is an essential safety feature.

Symptoms of a failing Microwave Door Switch include:

The microwave not starting or heating
Running when the door is opened
Unusual noises when the door is closed

Causes of a bad Microwave Door Switch can result from repeated opening and closing of the door or slamming that can cause the switch to degrade or become misaligned, leading to intermittent or failure.

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.

This part fixes the following symptoms

Doesn't shut off
No heat
Won't start

Do-It-Yourself Stories from Customers like You Ge microwave ran when turned off if door was shut Jason A. • Cary , NC • April 02, 2017

The first symptom was our microwave would continue to run after the time was up. The light would go out, the turn table would stop but you could still hear the microwave running and whatever was in it would continue to cook. The only way to stop it was to open the door. It was intermittent at first but eventually it would always run no matter what as long as the door was closed. Several other posts referenced these switches as the problem. I just replaced both and problem gone. It turns out... Read more

$26.54

Compare At:: $33.56
You Save:: $7.02

IN STOCK

Ships Today Guaranteed

Add to Cart

Best Seller

Genuine Samsung part

Kenmore Microwave Door Latch Hook

4.9 (79)

By: Samsung

Part Number: DE64-00760A

The Microwave Door Latch Hook is an essential component for maintaining the functionality of your Samsung microwave. This genuine OEM part ensures a secure and reliable connection between the microwave door and the main unit, providing peace of mind during every use. Crafted with precision, the Door Latch Hook guarantees a perfect fit for a range of Samsung microwave models, making installation straightforward and hassle-free. By replacing a worn or damaged latch hook with this high-quality part, you can restore the doorGÇÖs ability to stay firmly closed, preventing accidental openings and enhancing safety in your kitchen. Its durable construction is designed to withstand daily use, ensuring long-lasting performance and reliability. Whether your microwave door isnGÇÖt staying shut properly or you need to replace a broken latch, the Microwave Door Latch Hook offers a dependable solution. Invest in this genuine OEM part to keep your Samsung microwave operating smoothly and efficiently, providing you with the dependable performance you expect from your appliance.

This part fixes the following symptoms

Door won't close
Door stuck closed

Do-It-Yourself Stories from Customers like You Broken door latch Peter E. • Loxahatchee , FL • April 04, 2014

This was much easier than expected. I called Appliance Parts Pros with my model # and you told me what part I needed. It was shipped the same day and arrived the next day. I removed the inner door trim with a table knife ( don't rush this or you might crack the trim ). I then unhooked the old door latch disconnected the spring from the door hooked on the spring from the new latch and clipped in the latch to the door. Final step was to reattach the door trim. It was very easy and all I used... Read more

$22.95

Compare At:: $27.54
You Save:: $4.59

IN STOCK

Ships Today Guaranteed

Add to Cart

Best Seller

Genuine Frigidaire part

Kenmore Small Surface Element Switch

4.9 (63)

By: Frigidaire

Part Number: 316436000

The Small Surface Element Switch is an OEM replacement part for Frigidaire electric ranges. It serves as the control knob and circuitry to safely power one of the smaller cooking elements.

Symptoms of a bad surface element switch include:

Inability to ignite or regulate heating for its assigned zone
Switch knob that feels loose, won't click smoothly, or won't stay set
Intermittent or unreliable power to the smaller element coils
Tripped circuit breakers upon use that don't reset

Causes relate to thousands of rotations wearing micro-switches and wiring terminals within the control assembly. Regular cleaning around knobs can prevent accelerated deterioration from baked-on debris conducting excess heat.

This genuine OEM replacement part is compatible with other brands including Electrolux and Kenmore as well.

This part fixes the following symptoms

Element will not heat

Do-It-Yourself Stories from Customers like You Surface switches not operating properly; going from cool to very hot etc Guy G. • Guthrie , OK • October 10, 2014

Replaced all four element switches. Switches arrived within two days of ordering. That's about normal for AppliancePartsPros. They were the correct ones; not generic, and fit the original control knobs perfectly. This kind of service is what I'm used to from ApplicanePartsPros. Read more

$62.64

Compare At:: $73.92
You Save:: $11.28

IN STOCK

Ships Today Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Kenmore Oven Igniter

4.9 (101)

By: Whirlpool

Part Number: WP9758079

The Oven Igniter is an OEM part for Whirlpool ovens. It is designed to ignite the gas in the oven burner, providing the heat necessary for baking or broiling. This igniter is critical for the oven’s functionality, as it must heat up to a specific temperature to open the gas valve and begin the combustion process.

Symptoms of a bad Oven Igniter include:

The oven failing to heat up despite the gas being turned on.
A gas smell indicating that gas is being released without ignition.
Intermittent heating, where the oven fails to maintain a consistent temperature.

Causes of a bad oven igniter can include aging and wear that reduce the igniter’s ability to reach the required temperature, electrical issues such as faulty wiring or connections, or a malfunctioning safety valve that doesn’t open properly.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This part fixes the following symptoms

Won't start

Do-It-Yourself Stories from Customers like You The igniter in my whirlpool gas range needed replacement Thomas B. • Cobleskill , NY • November 24, 2014

There are hex screws keeping the igniter in place. I think they were 5/16...so you have to have a socket wrench. The space is kind of tight, and it's all on the right side, so if you're left handed (like I am) it's going to be a challenge to get the hex screws out without dropping them. Dropping them isn't too bad if they don't fall into the hole the gas pipe is coming through. Unfortunately one of them fell in there, and there's no getting it out of there. I had a machine screw that fit, so I... Read more

$45.95

Compare At:: $54.68
You Save:: $8.73

IN STOCK

Ships Today Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Kenmore Stove Top Drip Pan

4.9 (224)

By: Whirlpool

Part Number: WPW10196405

The Stove Top Drip Pan is an OEM replacement part for Whirlpool ranges. It is the shallow metal pan located below the stove burner elements that collects grease and food particles. The drip pan helps direct spills and drips away from the burner area to the bottom drawer for easy cleanup.

Symptoms of a bad drip pan include:

Grease or food spilling below the burners outside of the pan
Burner elements showing signs of corrosion or damage from drips
The drip pan no longer fitting properly or securely in place

Causes can be warping or damage of the drip pan over time due to exposure to heat. Dents and structural changes compromise its ability to direct drips properly.

This OEM replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

If you require a compatible 6-inch drip bowl, suggest considering our WPW10196406 model for a perfect fit. For a black option include the 6-inch W10290353RW and 8-inch WPW10290350 models.

This part fixes the following symptoms

Element will not heat

Do-It-Yourself Stories from Customers like You Our range needed 4 new range top elements due to wear Dale D. • Orlando , FL • December 05, 2014

$9.95

Compare At:: $11.94
You Save:: $1.99

IN STOCK

Ships Today Guaranteed

Add to Cart

Appliance

Appliance

Lawn & Garden

Need help finding dishwasher parts?

Need help finding dishwasher parts?

Need help finding dishwasher parts?

Kenmore / Sears Wall Oven Parts

Kenmore Heating Element

Kenmore Top Burner Receptacle Kit

Kenmore Infinite Switch Top Burner Control Switch

Kenmore Outer Oven Door Glass

Kenmore Oven Bake Element

Kenmore Oven Bake Element

Kenmore Range Surface Burner Control Switch

Kenmore Oven Igniter

Kenmore Surface Burner Terminal Block Kit

Kenmore Oven Bake Element

Kenmore Oven Bake Element

Kenmore Door Switch

Kenmore Microwave Door Latch Hook

Kenmore Small Surface Element Switch

Kenmore Oven Igniter

Kenmore Stove Top Drip Pan

Related Parts

Popular Kenmore Wall Oven Models