Your privacy choices: We and our partners use cookies for analytics and ads. Decline all turns them off.
Privacy Policy · Do Not Sell or Share My Personal Information
Need Help?
Call
This is a 9-inch radiant heating element that sits beneath the glass cooktop surface on an electric range. It converts electrical energy into heat to warm pots and pans placed above it. Replace this element if the burner won't heat, heats unevenly, glows only partially, or has visible damage such as cracks or burn spots.
Order the part to ApliancePartsPro and within 3 days I had it delivered to my front door. Looked up in their help page and was guided how to do it. It was so ease . I will recomend all my friend to get their parts at ApliancePartsPro. I am very please with the service and quality. Read more
Fix a microwave that won't start or stops mid-cycle with this door interlock monitor switch. Ensures safe operation when door closes. DIY repair.
Removed and replaced 3 door switches and mounting bar that holds switches plastic gets brittle with age and each switch comes out slightly different from each other, the chances of breaking a mounting pin is very easy. care should be taken when snapping mounting bar back into place to insure top latch and bottom latch locate properly insure bar is proper aligned when tightening screws their is free play in mounting bracket that could affect door properly engaging switches. NOTE that their are... Read more
The Radiant Element is an OEM part for GE ranges and cooktops. This part provides efficient and even heating for cooking. This part uses electricity to heat up and transfer warmth directly to the cookware. The radiant element is encased under the glass surface of the cooktop, offering a sleek and easy-to-clean cooking area while ensuring optimal heat distribution and cooking performance.
Causes of failure might include a burnt-out heating coil, damage to the element's electrical connections, or a malfunction within the control system that regulates power to the element.
Symptoms of a bad Radiant Element include:
This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.
Stove is a GE Adora Model JBP63HH2bb. It took me forever to figure out how the burner was attached to the rails. My glass top was different than any instructions found on the internet for changing out a burner. The burners on this one are held to the bottom of the glass cook top by two rails that cross the bottom of the burner assemblies. In order to get too the burners you must remove 4 Phillips screws to lower the rails and burners from the cooktop. I suggest two people do this because... Read more
Burner not heating? Replace the element receptacle and wire kit. Fixes burned or broken receptacles causing inoperative burners. DIY-friendly repair.
I ordered the recommended Infinite Heat Switch Kit and Element Receptacle and Wire Kit and installed them. The latter was a breeze, appearing to be exactly the same as the original, except for the wire color. The switch, though, was another story. It is a RobertShaw "replacement" part, designed, it seems, for use in the greatest number of original units as possible. The most obvious difference between this switch and the original (besides its comparatively small size) is the long, segmented... Read more
Replace cracked, stained, or worn drip pans that sit beneath burner elements. Catches spills and crumbs during cooking. Easy cosmetic upgrade.
Ordered replacement drip pans Read more
Oven won't heat or bakes unevenly? A failed bake element is likely the cause. This lower heating element replacement typically takes 30 minutes or less.
Turned off the power to the oven, removed the old element and installed a new element that I purchased from Appliance Pros.com. The part was delivered in a timely manner and was packed securely for shipping. Thanks!!!!!! Read more
This gas surface burner valve controls the flow of gas to a 16,000 BTU burner on your range cooktop. It connects to the gas supply line and is operated by the corresponding control knob. Replace this valve if your burner won't light, the flame is uneven or won't adjust properly, or you detect a gas smell when the knob is in the off position.
Ordered correct replacement parts (your online form helped to identify correct valves 2 had black dot on inside stem for back small burner 1 had red dot for larger front burner). locked stove, turned off gas, unplugged cord. removed knobs, 5 screws and front plate also removed L shaped plate below knobs for better access to comp. fittings. pulled off ignitior controls loosened compression fittings (hard to get wrench on nut but doable), removed screw holding valve to manifold. reversed order... Read more
Burner base holds and secures the gas burner assembly on your cooktop. Replace if cracked, warped, or corroded to restore proper burner seating.
Cleaned/ soaked all burners in Ammonia and scraped off the remaining with a pumice stone. Oiled all screws. Replaced (4) ignitors or electrodes and module kit/ right front burner/ burner switch harness. Although this was the third order of switches from 3 different places including the local supplier due to the switches being manufactured upside down and lit on low on the first attempt. (Since I was going to have to open it up again to either repair or remove and return the upside-down harness... Read more
The Large Surface Element is an OEM component for Whirlpool ranges. As a key heat source, it withstands significant thermal stresses each use for cooking tasks. This surface element measures approximately 10” in diameter.
Over time, microfractures may accumulate in the ceramic glass from repetitive heating/cooling cycles. Mineral deposits also build up on the surface, reducing heat transfer effectiveness.
Symptoms involve:
The element is compatible also for select KitchenAid and Maytag appliances.
Replaced the Infinite Switch and that solved the problem. Did not need to replace the Surface Element Read more
Seals oven door to prevent heat loss and improve cooking efficiency. Replace when brittle, frayed, or not sealing properly. Verify fit by model number.
First of all Appliance Parts Pros is the best!! I would not have had the confidence to make this repair myself without their outstanding videos and Q&A sections on their website. And their prices for parts are very competitive. Like many stories on the website, my oven would heat up beyond the temperature set point. When it reached the target temperature, the lower heating element (I think this is the “bake” element) would shutoff, but the top element (“broil” element I believe) would remain on... Read more
Fix an oven that won't light or hold temperature with this gas range igniter. Common repair for clicking sounds without ignition. DIY-friendly, 10-20 min.
Replaced the gas regulator and the oven igniter. It was not a very difficult repair.. most of the parts were easy to get to. The biggest challenge was disconnecting the gas hose from the regulator. It had "pipe dope" (sealant) on the threads. I reconnected with yellow gas pipe tape. Read more
Burner not heating or working intermittently? This surface element receptacle connects your heating element to power. DIY-friendly repair in under 1 hour.
Watched the video when the part came, and 5 minutes later, our 25 year old stove is once again working like a champ. Read more
Broiler not heating or turning red? This broil element restores high-heat broiling. DIY-friendly repair, typically takes 10-15 minutes with basic tools.
With my tools Read more
Oven won't heat after self-cleaning? This high-limit thermostat cuts power when temperatures get too high. Moderately easy DIY repair fix.
Online chat here said that the oven sensor should be replaced. I got the feeling that was a bit off, so I went with my gut and ordered the thermostat as well. Replaced the sensor and that didn't fix it. Replaced the thermostat and it worked like a charm! Disappointed that they were overconfident in their answer and it would have taken me more days to fix - but, the products came in quickly (basically, next day) and were correct. Online video for my particular oven was incorrect - but it's... Read more
This metal bracket provides structural support for range components like burner assemblies or control panels. It securely holds parts in their proper position during normal cooking operations. Replace when range components become loose, sag, or don't align properly.
Watched the appliancepartspro video and changed it out. It took about 15 minutes. I'm sure I saved hundreds. Read more
The Medium Surface Burner is an OEM part for GE ranges and cooktops. This burner is essential for a wide range of cooking tasks, from simmering sauces to sautéing vegetables. The medium surface burner ensures even heat distribution and efficient fuel consumption, contributing to the overall cooking performance of your appliance.
Causes of a bad Medium Surface Burner can range from clogged burner ports, which impede gas flow and affect flame consistency, to wear and tear on the igniter or the burner assembly that prevents proper operation.
Symptoms of a malfunctioning Medium Surface Burner include:
Took off old, replaced with new. Cross reference worked well, all GE parts. Saved a lot of money compared to local supplier. Read more
Opt-Out Request Honored
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.