Kenmore / Sears Washer Control Board

This part is an control board for washers. The control board is the part that controls the main functions of a washing machine. It is the main component that sends signals to the washer to perform its intended functions, controlling the desired washer settings. If the washing machine is not filling with water, spinning normally, or draining properly, this might mean it's time for a new control board. While it might seem difficult to replace this part, it's actually a simple process. First, pull the washer forward to access the back panel. Remove the upper back panel. Push the front of the control panel and pry it up with a putty knife removing it from the mounting brackets. Disconnect any wires attached to the old control board and be sure to take note of which wires go where by taking a photo with a phone camera. Then disconnect the air hose. Remove the mounting screws from the control board. Release the locking tabs and pull the control board out of the console. Position the new board in place and pop it into the locking tabs. Reconnect the air hose to the back of the control panel, and reconnect the wires into the back of the new control board. This genuine control board is compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore brand washers.

This oven timer is the control clock used to set and monitor cooking time and signal when baking or roasting cycles end. It restores timed cook functions and audible end-of-cycle alerts on compatible ranges. What it does:

• Controls and displays oven cook time and countdown functions
• Triggers the end-of-cycle tone when the set time completes
• Works with the oven's control circuitry to enable timed bake/roast operations
• Commonly replaced when timers fail to advance, don't keep time, or don't sound the end-of-cycle alert

• One oven timer assembly

• Disconnect power to the appliance before beginning any repair
• Access may require removing the control panel or back cover; handle trim and wiring carefully
• Transfer any knobs or mounting hardware from the old timer unless new hardware is provided

This is a timer that is used on washing machines. It controls the electrical components and the length of time of the washing machine's cycles. Be sure to unplug the appliance from the electrical outlet before beginning repairs. Some people performing the replacement or repair may wish to wear work gloves to protect their hands. The replacement process only takes about ten minutes to complete from start to finish.When the timer will not advance, it is likely that the washing machine cycles will not run at all or won't run consistently. The appliance may not advance through the various cycles like the washing, rinsing, and spinning cycles and may get stuck on one of the cycles. This timer is compatible with washing machines that are manufactured by Kenmore, Gibson, Westinghouse, and Frigidaire. It is sold individually and is sourced directly from the manufacturer and a genuine OEM part.

This electronic control board replaces the oven/range console's main control, restoring user interface and cycle control so the appliance can accept commands and run selected functions. It helps resolve issues caused by a failed control module. What it does:

• Controls front-panel functions, timers, and user inputs for oven/range operation
• Processes commands from the touchpad/knobs and sends signals to relays, bake/broil elements, and lights
• Commonly used when displays are blank, controls are unresponsive, or cycles fail to start
• Works as the main logic board that coordinates heating and timed functions

• One electronic control board

• Disconnect power at the breaker or unplug the appliance before starting
• Handle the board carefully; avoid electrostatic discharge and damage to terminals
• Keep track of wire locations or take photos before disconnecting connectors

This electronic control board replaces the appliance's main logic module to restore keypad/display operation and cycle control. It ensures the unit responds correctly to user inputs and runs programmed cycles when the original board fails. What it does:

• Manages user interface signals, timed cycles, and electronic controls for normal operation
• Resolves symptoms such as unresponsive buttons, blank or erratic display, or appliances that won't start or complete cycles
• Replaces a failed or intermittent main circuit board to stop random resets or control errors
• Works as the primary control for coordinating sensors, timers, and relays

• One electronic control board

• Disconnect power before accessing or replacing the control board to avoid shock or damage
• Handle the board by its edges and avoid touching components or connector pins
• Some models require removing the console or control panel; keep track of screws and grounding straps
• If connectors are tight, gently pry straight out—do not force or bend pins

This washing machine main control board is manufactured by Whirlpool. This board is responsible for monitoring and managing all the functions of the washer, such as filling, agitating, spinning, and draining. A control board can suffer from corrosion and degradation due to exposure to heat, moisture, and other factors.Signs that the main control board may be faulty include erratic operation, failure to finish a cycle, or even complete failure of the appliance. The washer's display may also show error code F1 E1. To get the washer back in working condition the board will need to be replaced. After replacing the main control board, the washing machine will need to be recalibrated.This genuine OEM part is sold individually and is compatible with Whirlpool and Kenmore washing machines.

This electronic control board is the main circuit board that runs a range of appliance functions and the user interface. Replacing a faulty board restores responsive controls, display feedback, and normal programmed cycles. What it does:

• Manages the appliance's user interface, timing, and control signals for cycles and features
• Communicates with sensors and other modules to coordinate operation
• Prevents or causes faults when failing; common symptoms include unresponsive buttons, blank or erratic display, and interrupted cycles
• Helps restore normal operation when intermittent or incorrect control behavior is traced to the main board

• Disconnect power to the appliance before starting work to prevent shock or damage
• Handle the board by the edges and avoid touching component leads or solder joints
• Transfer any required brackets or harnesses from the old board and secure all connectors firmly
• Test the appliance after installation.

This electronic control board regulates oven/dryer functions and user interface so the appliance responds correctly to timer, temperature and cycle commands. Replacing a failed board restores control and display operation when the board is the root cause. What it does

• Receives inputs from the touchpad/knobs and runs the appliance's control logic
• Sends signals to heating, motor and indicator components to start and stop cycles
• Controls the display and status lights so cycle information is shown correctly
• Commonly used when controls are unresponsive, display is blank/flickering, or cycles no longer start

• One electronic control board

• Disconnect power at the breaker or unplug the appliance before starting any work
• Handle the board carefully to avoid electrostatic discharge (ESD) damage; use an anti-static strap if available
• Verify electrical connections and board orientation match the original before reassembly

This electronic control board manages the refrigerator's user interface and appliance functions so the unit responds correctly to commands and cycles. Replacing a faulty board restores normal control and system coordination. What it does:

• Interprets user inputs and runs compressor, fans, lights, defrost and dispenser functions
• Controls timed cycles and temperature regulation logic
• Works with sensors and relays to ensure coordinated appliance operation

• Disconnect power to the appliance before you start any work
• Handle the board by the edges and avoid static discharge; use proper ESD precautions if available
• Label and transfer wire harnesses and mounting hardware exactly as found to ensure proper reconnection

Made to be used on washing machines, this part is a timer. This component controls the electrical parts and the duration of time of the washing machine's cycles. It controls the operation of the washing machine, including each of the cycles.When the timer will not advance, the washing machine could become stuck in a cycle and run constantly without stopping. The washing machine may not advance through the particular cycle like the washing, rinsing, or spinning and could get stuck on one of the cycles. It's important to unplug the washing machine from the electrical outlet before attempting to repair or replace any parts. The replacement process is fairly easy and takes about 15 minutes to complete.This timer is compatible with washing machines that are manufactured by the Frigidaire, Gibson, Kenmore, and White-Westinghouse brands. This part is sold individually and is sourced straight from the manufacturer itself.