Kenmore / Sears Washer Hose Or Tube

Two 5-foot nylon braided hoses connect household water supply to washer inlet valves. Replace cracked, leaking, or aging hoses to prevent water damage.

Contains two, six foot long braided hoses with 90 degree ends.

Connects washer drain hose to extension hose. Includes coupling and clamps. Replace if cracked, broken, or when extending drain hose length to reach pipe.

21-inch drain hose extension for washers. Extends existing drain hose when original is too short to reach standpipe. Includes clamp for secure fit.

This inlet hose carries supply water into the washer during the fill cycle. Replacing a worn or leaking hose restores proper water flow and helps prevent leaks and fill errors that can leave clothes unwashed or floors wet.

• Channels incoming water from the inlet valve into the washer
• Maintains a sealed connection to prevent drips and leaks
• Replaces hoses that are cracked, swollen, kinked, or clogged with mineral deposits
• Common symptoms: water leaking during fill, reduced water flow or fill error codes, visible cracks/splits

• Disconnect power and turn off both water supply valves before servicing
• Keep towels or a container handy; residual water may spill when removing hoses
• Note hose routing; fully seat ends and secure with existing or new clamps as required
• Restore water and power, then run a quick fill to check all connections for leaks

This is a flexible drain hose that connects the washing machine's pump to the household drain standpipe or laundry tub. It channels used wash and rinse water out of the machine during the drain and spin cycles. Replace this hose if you notice leaks at the connections, cracks or splits in the hose material, or if the washer is not draining properly due to a restricted or damaged hose.

Connect hot and cold water faucets to your washer's inlet valves with this 2-pack of 5-foot fill hoses. Replace aging, cracked, or leaking supply lines.

This is a small hose that connects to the dispenser valve assembly inside the washing machine, directing water into the detergent or fabric softener dispenser. It ensures proper water flow to the dispenser during the wash cycle. Replace this hose if you notice leaking near the dispenser area, detergent not being flushed into the drum, or visible cracks and deterioration on the hose.

Replacement flexible hose that routes water inside your washer. Needed when original is cracked, kinked, worn, or leaking. Restores secure flow.

Carries water from home supply to washer inlet valve. Replace if your hose is cracked, worn, leaking, or damaged by pests or age. Restores proper fill.

Pressure tube connects washer tub to water level switch. Replace if cracked, kinked, or clogged to restore proper water level sensing in your laundry center.

5 foot. Package of 2.

Washer air chamber connects the water level pressure switch to the tub. Replace if cracked, kinked, or disconnected causing water level issues.

This hose kit replaces worn or damaged appliance hoses to restore proper water flow and prevent leaks. It's a direct-fit replacement for compatible Whirlpool systems and helps stop visible leaks and restore normal fill/drain operation. What it does

• Replaces cracked, split or leaking hoses to stop water loss and reduce risk of appliance damage
• Restores reliable water flow for filling and draining functions
• Helps eliminate poor draining, intermittent filling, or water pooling near the appliance
• Works with existing clamps and connections when installed correctly

• Disconnect power and shut off the water supply before starting any repair
• Inspect connection fittings and replace clamps if worn; ensure a snug, leak-free fit
• Route hoses without kinks and secure to avoid chafing or strain
• After installation, run a short cycle and check all connections for leaks

Replace your washer's cracked or leaking drain hose. This flexible hose connects the tub to the drain system. Essential when the original is damaged or worn.

Size: 6 foot long. Washers not included. This is one hose, for a set with washers order 285363. For inlet hose screen use 285452A and for inlet hose washers use 285448A